--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-3.10-3-amd64: Network adapter (Intel 82579V) hangs during TX, causing reset and undetected data corruption at the other side
- From: "T.A. van Roermund" <timo@van-roermund.nl>
- Date: Tue, 22 Oct 2013 20:02:22 +0200
- Message-id: <20131022180222.11009.92211.reportbug@server-timo.van-roermund.nl>
Package: src:linux
Version: 3.10.11-1
Severity: critical
Justification: causes serious data loss
Dear Maintainer,
Since the upgrade from kernel version 3.2.0-4 to 3.10-3 I get serious data corruption on the network connection between my server and my desktop PC. The server has the Intel Corporation 82579V Gigabit Network Connection (rev 04) network adapter installed, which is connected via a Conceptronic gigabit switch to my desktop PC. The server is (via a second network interface) also connected to the internet and acts as a router/firewall to my internal network. When I download a large file on my desktop PC, it can happen that the data that is downloaded is corrupted without being detected by the desktop PC. It doesn't always happen, but it is quite likely that it happens when downloading a large file. And if this happens, the syslog on my server shows the following entries:
kernel: [198328.514116] e1000e 0000:00:19.0 eth2: Detected Hardware Unit Hang:
kernel: [198328.514116] TDH <0>
kernel: [198328.514116] TDT <2>
kernel: [198328.514116] next_to_use <2>
kernel: [198328.514116] next_to_clean <0>
kernel: [198328.514116] buffer_info[next_to_clean]:
kernel: [198328.514116] time_stamp <102f3a7d0>
kernel: [198328.514116] next_to_watch <1>
kernel: [198328.514116] jiffies <102f3a90b>
kernel: [198328.514116] next_to_watch.status <0>
kernel: [198328.514116] MAC Status <40080083>
kernel: [198328.514116] PHY Status <796d>
kernel: [198328.514116] PHY 1000BASE-T Status <3800>
kernel: [198328.514116] PHY Extended Status <3000>
kernel: [198328.514116] PCI Status <10>
The MAC/PHY/PCI status (last 5 lines) is always the same.
In the mean time I have found a solution to this problem: if I disable TCP segmentation offload using the command 'ethtool -K eth2 tso off', the problem does no longer occur.
This is a very serious bug, especially since the receiving side (my desktop PC) cannot detect that the data transmitted over the network is corrupt.
-- Package-specific info:
** Version:
Linux version 3.10-3-amd64 (debian-kernel@lists.debian.org) (gcc version 4.7.3 (Debian 4.7.3-7) ) #1 SMP Debian 3.10.11-1 (2013-09-10)
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.10-3-amd64 root=UUID=42e365d5-330b-438b-8948-82308bd455a1 ro quiet
** Not tainted
** Kernel log:
[ 1.426887] usb 2-1: New USB device found, idVendor=8087, idProduct=0024
[ 1.426892] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.427304] hub 2-1:1.0: USB hub found
[ 1.427482] hub 2-1:1.0: 6 ports detected
[ 1.450724] PM: Starting manual resume from disk
[ 1.450729] PM: Hibernation image partition 8:3 present
[ 1.450730] PM: Looking for hibernation image.
[ 1.450855] PM: Image not found (code -22)
[ 1.450858] PM: Hibernation image not present or could not be loaded.
[ 1.566552] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.152495] systemd-udevd[327]: starting version 204
[ 3.636012] ACPI Warning: 0x000000000000f040-0x000000000000f05f SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20130328/utaddress-251)
[ 3.636019] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.663370] ACPI Warning: 0x0000000000000428-0x000000000000042f SystemIO conflicts with Region \PMIO 1 (20130328/utaddress-251)
[ 3.663377] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.663381] ACPI Warning: 0x0000000000000530-0x000000000000053f SystemIO conflicts with Region \GPIO 1 (20130328/utaddress-251)
[ 3.663384] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.663385] ACPI Warning: 0x0000000000000500-0x000000000000052f SystemIO conflicts with Region \GPIO 1 (20130328/utaddress-251)
[ 3.663388] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 3.663389] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 3.767693] mei_me 0000:00:16.0: setting latency timer to 64
[ 3.767736] mei_me 0000:00:16.0: irq 43 for MSI/MSI-X
[ 3.808660] input: PC Speaker as /devices/platform/pcspkr/input/input1
[ 3.838116] ACPI: Requesting acpi_cpufreq
[ 3.878944] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input2
[ 3.879006] ACPI: Power Button [PWRB]
[ 3.879057] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 3.879082] ACPI: Power Button [PWRF]
[ 3.897465] parport_pc 00:09: reported by Plug and Play ACPI
[ 3.897523] parport0: PC-style at 0x378, irq 5 [PCSPP,TRISTATE]
[ 3.947049] microcode: CPU0 sig=0x206a7, pf=0x2, revision=0x28
[ 4.004052] platform microcode: firmware: agent aborted loading intel-ucode/06-2a-07 (not found?)
[ 4.004132] microcode: CPU1 sig=0x206a7, pf=0x2, revision=0x28
[ 4.007609] platform microcode: firmware: agent aborted loading intel-ucode/06-2a-07 (not found?)
[ 4.007747] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 4.060458] [drm] Initialized drm 1.1.0 20060810
[ 4.117804] systemd-udevd[374]: renamed network interface eth1 to rename3
[ 4.122612] iTCO_vendor_support: vendor-support=0
[ 4.122934] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.10
[ 4.122962] iTCO_wdt: Found a Panther Point TCO device (Version=2, TCOBASE=0x0460)
[ 4.123024] iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
[ 4.169761] systemd-udevd[371]: renamed network interface eth0 to eth1
[ 4.193728] systemd-udevd[374]: renamed network interface rename3 to eth0
[ 4.283153] [drm] Memory usable by graphics device = 2048M
[ 4.283160] i915 0000:00:02.0: setting latency timer to 64
[ 4.301047] i915 0000:00:02.0: irq 44 for MSI/MSI-X
[ 4.301057] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 4.301059] [drm] Driver supports precise vblank timestamp query.
[ 4.301158] vgaarb: device changed decodes: PCI:0000:00:02.0,olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 4.309506] [drm] Wrong MCH_SSKPD value: 0x16040307
[ 4.309509] [drm] This can cause pipe underruns and display issues.
[ 4.309510] [drm] Please upgrade your BIOS to fix this.
[ 4.340391] fbcon: inteldrmfb (fb0) is primary device
[ 4.585695] Console: switching to colour frame buffer device 210x65
[ 4.593657] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 4.593659] i915 0000:00:02.0: registered panic notifier
[ 4.618066] acpi device:5e: registered as cooling_device7
[ 4.618351] acpi device:5f: registered as cooling_device8
[ 4.618646] acpi device:60: registered as cooling_device9
[ 4.618902] acpi device:61: registered as cooling_device10
[ 4.619175] acpi device:62: registered as cooling_device11
[ 4.619453] acpi device:63: registered as cooling_device12
[ 4.619729] acpi device:64: registered as cooling_device13
[ 4.620008] acpi device:65: registered as cooling_device14
[ 4.620047] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 4.620097] input: Video Bus as /devices/LNXSYSTM:00/device:00/PNP0A08:00/LNXVIDEO:00/input/input4
[ 4.621164] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
[ 4.682296] snd_hda_intel 0000:00:1b.0: irq 45 for MSI/MSI-X
[ 4.730924] input: HDA Intel PCH Line Out as /devices/pci0000:00/0000:00:1b.0/sound/card0/input5
[ 4.730999] input: HDA Intel PCH Line as /devices/pci0000:00/0000:00:1b.0/sound/card0/input6
[ 4.731052] input: HDA Intel PCH Rear Mic as /devices/pci0000:00/0000:00:1b.0/sound/card0/input7
[ 5.813453] [drm] Enabling RC6 states: RC6 on, RC6p off, RC6pp off
[ 5.919521] Adding 16396284k swap on /dev/sda3. Priority:-1 extents:1 across:16396284k
[ 5.965094] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 6.144385] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 6.464900] fuse init (API version 7.22)
[ 6.500360] loop: module loaded
[ 6.613711] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 7.422730] 8139too 0000:01:00.0 eth1: link up, 100Mbps, full-duplex, lpa 0x41E1
[ 7.609112] e1000e 0000:00:19.0: irq 40 for MSI/MSI-X
[ 7.712515] e1000e 0000:00:19.0: irq 40 for MSI/MSI-X
[ 7.712663] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready
[ 8.036985] r8169 0000:01:02.0 eth0: link down
[ 8.037012] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 8.037041] r8169 0000:01:02.0 eth0: link down
[ 10.586420] r8169 0000:01:02.0 eth0: link up
[ 10.586430] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 11.204326] e1000e: eth2 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: Rx/Tx
[ 11.204360] IPv6: ADDRCONF(NETDEV_CHANGE): eth2: link becomes ready
[ 15.431398] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 16.300618] RPC: Registered named UNIX socket transport module.
[ 16.300622] RPC: Registered udp transport module.
[ 16.300624] RPC: Registered tcp transport module.
[ 16.300625] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 16.340094] FS-Cache: Loaded
[ 16.340535] Key type dns_resolver registered
[ 16.390864] FS-Cache: Netfs 'nfs' registered for caching
[ 16.476035] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 48.866569] ip6_tables: (C) 2000-2006 Netfilter Core Team
[32346.022565] nf_conntrack: automatic helper assignment is deprecated and it will be removed soon. Use the iptables CT target to attach helpers instead.
** Model information
sys_vendor:
product_name:
product_version:
chassis_vendor:
chassis_version:
bios_vendor: Intel Corp.
bios_version: ENB7510H.86A.0046.2013.0704.1354
board_vendor: Intel Corporation
board_name: DB75EN
board_version: AAG39650-302
** Loaded modules:
ip6table_filter
ip6_tables
nfsd
auth_rpcgss
oid_registry
nfs_acl
nfs
lockd
dns_resolver
fscache
sunrpc
xt_nat
xt_REDIRECT
ipt_MASQUERADE
xt_conntrack
xt_tcpudp
iptable_mangle
iptable_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_nat_ipv4
nf_nat
iptable_filter
ip_tables
x_tables
nf_conntrack_ftp
nf_conntrack
loop
fuse
snd_hda_codec_realtek
snd_hda_intel
coretemp
snd_hda_codec
kvm_intel
kvm
crc32c_intel
snd_hwdep
i915
ghash_clmulni_intel
snd_pcm
cryptd
iTCO_wdt
iTCO_vendor_support
drm_kms_helper
drm
microcode
snd_page_alloc
parport_pc
parport
video
button
mperf
processor
i2c_algo_bit
pcspkr
mei_me
snd_seq
snd_seq_device
snd_timer
mei
snd
evdev
lpc_ich
mfd_core
i2c_i801
i2c_core
soundcore
ext4
crc16
jbd2
mbcache
sg
sd_mod
crc_t10dif
thermal
fan
thermal_sys
ahci
libahci
ehci_pci
xhci_hcd
ehci_hcd
libata
scsi_mod
r8169
8139too
8139cp
mii
e1000e
usbcore
usb_common
ptp
pps_core
** Network interface configuration:
auto lo
iface lo inet loopback
auto eth1
iface eth1 inet static
address 192.168.10.1
network 192.168.10.0
netmask 255.255.255.0
broadcast 192.168.10.255
auto eth2
iface eth2 inet static
address 192.168.11.1
network 192.168.11.0
netmask 255.255.255.0
broadcast 192.168.11.255
post-up /sbin/ethtool -K eth2 tso off
auto eth0
iface eth0 inet dhcp
post-up /root/scripts/cron/set_iptables_rules.sh
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
valid_lft forever preferred_lft forever
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN group default qlen 1000
link/ether 00:0e:2e:03:c5:e4 brd ff:ff:ff:ff:ff:ff
inet 192.168.10.1/24 brd 192.168.10.255 scope global eth1
valid_lft forever preferred_lft forever
inet6 fe80::20e:2eff:fe03:c5e4/64 scope link
valid_lft forever preferred_lft forever
3: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:c0:49:f2:7c:11 brd ff:ff:ff:ff:ff:ff
inet 77.249.127.162/24 brd 255.255.255.255 scope global eth0
valid_lft forever preferred_lft forever
inet6 fe80::2c0:49ff:fef2:7c11/64 scope link
valid_lft forever preferred_lft forever
4: eth2: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:1e:8c:f1:7a:cd brd ff:ff:ff:ff:ff:ff
inet 192.168.11.1/24 brd 192.168.11.255 scope global eth2
valid_lft forever preferred_lft forever
inet6 fe80::21e:8cff:fef1:7acd/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
eth0: 1748829594 1702226 0 0 0 0 0 0 44466040 499043 0 0 0 0 0 0
eth1: 4678182 24524 0 7 0 0 0 0 30335501 30491 0 0 3 0 0 0
eth2: 2612746153 2241810 0 0 0 0 0 2770 1796617099 1620531 0 0 0 0 0 0
lo: 334815 2089 0 0 0 0 0 0 334815 2089 0 0 0 0 0 0
*** Protocol statistics:
Ip:
1896374 total packets received
1370257 forwarded
0 incoming packets discarded
476127 incoming packets delivered
1861746 requests sent out
1 fragments dropped after timeout
9 reassemblies required
4 packets reassembled ok
1 packet reassembles failed
3 fragments received ok
8 fragments created
Icmp:
3386 ICMP messages received
6 input ICMP message failed.
InCsumErrors: 4
ICMP input histogram:
destination unreachable: 3293
timeout in transit: 41
redirects: 1
echo requests: 47
1170 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 1122
time exceeded: 1
echo replies: 47
IcmpMsg:
InType3: 3293
InType5: 1
InType8: 47
InType11: 41
OutType0: 47
OutType3: 1122
OutType11: 1
Tcp:
214 active connections openings
172 passive connection openings
118 failed connection attempts
42 connection resets received
12 connections established
399893 segments received
487463 segments send out
652 segments retransmited
0 bad segments received.
152 resets sent
Udp:
75840 packets received
241 packets to unknown port received.
0 packet receive errors
52423 packets sent
UdpLite:
TcpExt:
7 resets received for embryonic SYN_RECV sockets
92 TCP sockets finished time wait in fast timer
298 delayed acks sent
Quick ack mode was activated 2 times
176023 packets directly queued to recvmsg prequeue.
19052668 bytes directly in process context from backlog
1437439311 bytes directly received in process context from prequeue
148742 packet headers predicted
187492 packets header predicted and directly queued to user
14861 acknowledgments not containing data payload received
75467 predicted acknowledgments
2 congestion windows recovered without slow start after partial ack
1 timeouts in loss state
18 other TCP timeouts
TCPLossProbes: 93
TCPLossProbeRecovery: 58
2 DSACKs sent for old packets
85 DSACKs received
23 connections reset due to unexpected data
1 connections reset due to early user close
5 connections aborted due to timeout
TCPDSACKIgnoredNoUndo: 59
TCPSackShiftFallback: 4
TCPDeferAcceptDrop: 28
IPReversePathFilter: 5
TCPRcvCoalesce: 51657
TCPOFOQueue: 41
TCPSpuriousRtxHostQueues: 213
IpExt:
InNoRoutes: 6
InMcastPkts: 2077
OutMcastPkts: 250
InBcastPkts: 52606
OutBcastPkts: 1208
InOctets: -78348503
OutOctets: -776949915
InMcastOctets: 924452
OutMcastOctets: 89055
InBcastOctets: 17232643
OutBcastOctets: 172146
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0100] (rev 09)
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0102] (rev 09) (prog-if 00 [VGA controller])
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 44
Region 0: Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at f000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:14.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB xHCI Host Controller [8086:1e31] (rev 04) (prog-if 30 [XHCI])
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f7d20000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
00:16.0 Communication controller [0780]: Intel Corporation 7 Series/C210 Series Chipset Family MEI Controller #1 [8086:1e3a] (rev 04)
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f7d3c000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:19.0 Ethernet controller [0200]: Intel Corporation 82579V Gigabit Network Connection [8086:1503] (rev 04)
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 40
Region 0: Memory at f7d00000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f7d39000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at f080 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #2 [8086:1e2d] (rev 04) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7d38000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 7 Series/C210 Series Chipset Family High Definition Audio Controller [8086:1e20] (rev 04)
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 45
Region 0: Memory at f7d30000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1d.0 USB controller [0c03]: Intel Corporation 7 Series/C210 Series Chipset Family USB Enhanced Host Controller #1 [8086:1e26] (rev 04) (prog-if 20 [EHCI])
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7d37000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge [8086:244e] (rev a4) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7c00000-f7cfffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation B75 Express Chipset LPC Controller [8086:1e49] (rev 04)
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 7 Series/C210 Series Chipset Family 6-port SATA Controller [AHCI mode] [8086:1e02] (rev 04) (prog-if 01 [AHCI 1.0])
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 42
Region 0: I/O ports at f0d0 [size=8]
Region 1: I/O ports at f0c0 [size=4]
Region 2: I/O ports at f0b0 [size=8]
Region 3: I/O ports at f0a0 [size=4]
Region 4: I/O ports at f060 [size=32]
Region 5: Memory at f7d36000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 7 Series/C210 Series Chipset Family SMBus Controller [8086:1e22] (rev 04)
Subsystem: Intel Corporation Device [8086:2041]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at f7d35000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at f040 [size=32]
01:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at e100 [size=256]
Region 1: Memory at f7c31000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at f7c20000 [disabled] [size=64K]
Capabilities: <access denied>
Kernel driver in use: 8139too
01:02.0 Ethernet controller [0200]: U.S. Robotics USR997902 10/100/1000 Mbps PCI Network Card [16ec:0116] (rev 10)
Subsystem: U.S. Robotics USR997902 10/100/1000 Mbps PCI Network Card [16ec:0116]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (8000ns min, 16000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at e000 [size=256]
Region 1: Memory at f7c30000 (32-bit, non-prefetchable) [size=256]
Expansion ROM at f7c00000 [disabled] [size=128K]
Kernel driver in use: r8169
** USB devices:
Bus 002 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: jessie/sid
APT prefers testing
APT policy: (990, 'testing'), (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 3.10-3-amd64 (SMP w/2 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.10-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.51
ii initramfs-tools [linux-initramfs-tool] 0.114
ii kmod 9-3
ii linux-base 3.5
ii module-init-tools 9-3
Versions of packages linux-image-3.10-3-amd64 recommends:
ii firmware-linux-free 3.2
Versions of packages linux-image-3.10-3-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-27+deb7u2
pn linux-doc-3.10 <none>
Versions of packages linux-image-3.10-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.40
pn xen-hypervisor <none>
-- debconf information excluded
--- End Message ---