Your message dated Mon, 23 Nov 2020 10:41:25 +0000 with message-id <0b90a840471d86834671e45cc6294e4d5f1bf953.camel@decadent.org.uk> and subject line Re: Bug#974939: machine does not boot has caused the Debian Bug report #974939, regarding machine does not boot to be marked as done. This means that you claim that the problem has been dealt with. If this is not the case it is now your responsibility to reopen the Bug report if necessary, and/or fix the problem forthwith. (NB: If you are a system administrator and have no idea what this message is talking about, this may indicate a serious mail system misconfiguration somewhere. Please contact owner@bugs.debian.org immediately.) -- 974939: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=974939 Debian Bug Tracking System Contact owner@bugs.debian.org with problems
--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: machine does not boot
- From: Toni <toni@debian.org>
- Date: Mon, 16 Nov 2020 19:41:05 +0000
- Message-id: <[🔎] 160555566531.21662.12288989478279065715.reportbug@laptop-t.office.oeko.net>
Package: src:linux Version: 4.19.152-1 Severity: critical Hi, with the two latest kernels, linux-image-4.19.0-12-amd64 and linux-image-4.19.0-11-amd64, my machine does not boot, the reason being that something with cryptsetup is amiss. I used to be asked for a passphrase, but using these two kernels, I'm not, and the machine just cycles trying to find the root partition. I am now running the -10 kernel again, which I would like to get off of. I've tried recovery mode without any success. On the console, after dmesg, these three lines repeat ad nauseum: mdadm: No arrays found in config file or automatically Volume group "ev0" not found Cannot process volume group ev0 mdadm: No arrays found in config file or automatically Volume group "ev0" not found Cannot process volume group ev0 I think this bug is critical, since I can't get to anything with this state of the machine. The disk configuration is pretty straightforward: git:(master*)$ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT nvme0n1 259:0 0 953.9G 0 disk ├─nvme0n1p1 259:1 0 238.4M 0 part ├─nvme0n1p2 259:2 0 3.5G 0 part ├─nvme0n1p3 259:3 0 953M 0 part /boot └─nvme0n1p4 259:4 0 949.2G 0 part └─nvme0n1p4_crypt 253:0 0 949.2G 0 crypt ├─ev0-swap 253:1 0 29.8G 0 lvm [SWAP] ├─ev0-root 253:2 0 789.4G 0 lvm / There is one other (data) partition, but that's it for what the system has. Cheers, Toni -- Package-specific info: ** Kernel log: boot messages should be attached ** Model information sys_vendor: Dell Inc. product_name: Precision 5530 product_version: chassis_vendor: Dell Inc. chassis_version: bios_vendor: Dell Inc. bios_version: 1.13.0 board_vendor: Dell Inc. board_name: 0X78C1 board_version: A02 ** PCI devices: 00:00.0 Host bridge [0600]: Intel Corporation 8th Gen Core Processor Host Bridge/DRAM Registers [8086:3ec4] (rev 07) Subsystem: Dell 8th Gen Core Processor Host Bridge/DRAM Registers [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Capabilities: <access denied> Kernel driver in use: skl_uncore 00:01.0 PCI bridge [0604]: Intel Corporation Skylake PCIe Controller (x16) [8086:1901] (rev 07) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 122 Bus: primary=00, secondary=01, subordinate=01, sec-latency=0 I/O behind bridge: 00003000-00003fff Memory behind bridge: ec000000-ed0fffff Prefetchable memory behind bridge: 00000000c0000000-00000000d1ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:02.0 VGA compatible controller [0300]: Intel Corporation UHD Graphics 630 (Mobile) [8086:3e9b] (prog-if 00 [VGA controller]) Subsystem: Dell UHD Graphics 630 (Mobile) [1028:087d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 154 Region 0: Memory at eb000000 (64-bit, non-prefetchable) [size=16M] Region 2: Memory at 80000000 (64-bit, prefetchable) [size=256M] Region 4: I/O ports at 4000 [size=64] [virtual] Expansion ROM at 000c0000 [disabled] [size=128K] Capabilities: <access denied> Kernel driver in use: i915 Kernel modules: i915 00:04.0 Signal processing controller [1180]: Intel Corporation Skylake Processor Thermal Subsystem [8086:1903] (rev 07) Subsystem: Dell Xeon E3-1200 v5/E3-1500 v5/6th Gen Core Processor Thermal Subsystem [1028:087d] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: Memory at ed510000 (64-bit, non-prefetchable) [size=32K] Capabilities: <access denied> Kernel driver in use: proc_thermal Kernel modules: processor_thermal_device 00:08.0 System peripheral [0880]: Intel Corporation Skylake Gaussian Mixture Model [8086:1911] Subsystem: Dell Xeon E3-1200 v5/v6 / E3-1500 v5 / 6th/7th Gen Core Processor Gaussian Mixture Model [1028:087d] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 255 Region 0: Memory at ed528000 (64-bit, non-prefetchable) [disabled] [size=4K] Capabilities: <access denied> 00:12.0 Signal processing controller [1180]: Intel Corporation Cannon Lake PCH Thermal Controller [8086:a379] (rev 10) Subsystem: Dell Cannon Lake PCH Thermal Controller [1028:087d] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: Memory at ed527000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel_pch_thermal Kernel modules: intel_pch_thermal 00:14.0 USB controller [0c03]: Intel Corporation Cannon Lake PCH USB 3.1 xHCI Host Controller [8086:a36d] (rev 10) (prog-if 30 [XHCI]) Subsystem: Dell Cannon Lake PCH USB 3.1 xHCI Host Controller [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 130 Region 0: Memory at ed500000 (64-bit, non-prefetchable) [size=64K] Capabilities: <access denied> Kernel driver in use: xhci_hcd Kernel modules: xhci_pci 00:14.2 RAM memory [0500]: Intel Corporation Cannon Lake PCH Shared SRAM [8086:a36f] (rev 10) Subsystem: Dell Cannon Lake PCH Shared SRAM [1028:087d] Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at ed51e000 (64-bit, non-prefetchable) [disabled] [size=8K] Region 2: Memory at ed526000 (64-bit, non-prefetchable) [disabled] [size=4K] Capabilities: <access denied> 00:15.0 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial IO I2C Controller [8086:a368] (rev 10) Subsystem: Dell Cannon Lake PCH Serial IO I2C Controller [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at 7f800000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel-lpss Kernel modules: intel_lpss_pci 00:15.1 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH Serial IO I2C Controller [8086:a369] (rev 10) Subsystem: Dell Cannon Lake PCH Serial IO I2C Controller [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 17 Region 0: Memory at 7f801000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: intel-lpss Kernel modules: intel_lpss_pci 00:16.0 Communication controller [0780]: Intel Corporation Cannon Lake PCH HECI Controller [8086:a360] (rev 10) Subsystem: Dell Cannon Lake PCH HECI Controller [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 139 Region 0: Memory at ed523000 (64-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: mei_me Kernel modules: mei_me 00:17.0 SATA controller [0106]: Intel Corporation Cannon Lake Mobile PCH SATA AHCI Controller [8086:a353] (rev 10) (prog-if 01 [AHCI 1.0]) Subsystem: Dell Cannon Lake Mobile PCH SATA AHCI Controller [1028:087d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 Interrupt: pin A routed to IRQ 129 Region 0: Memory at ed51c000 (32-bit, non-prefetchable) [size=8K] Region 1: Memory at ed522000 (32-bit, non-prefetchable) [size=256] Region 2: I/O ports at 4090 [size=8] Region 3: I/O ports at 4080 [size=4] Region 4: I/O ports at 4060 [size=32] Region 5: Memory at ed521000 (32-bit, non-prefetchable) [size=2K] Capabilities: <access denied> Kernel driver in use: ahci Kernel modules: ahci 00:1b.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port [8086:a340] (rev f0) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 123 Bus: primary=00, secondary=02, subordinate=3a, sec-latency=0 I/O behind bridge: 00005000-00005fff Memory behind bridge: d4000000-ea0fffff Prefetchable memory behind bridge: 0000000090000000-00000000b1ffffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port [8086:a338] (rev f0) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 124 Bus: primary=00, secondary=3b, subordinate=3b, sec-latency=0 Memory behind bridge: ed400000-ed4fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1c.4 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port [8086:a33c] (rev f0) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 125 Bus: primary=00, secondary=3c, subordinate=3c, sec-latency=0 Memory behind bridge: ed300000-ed3fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1d.0 PCI bridge [0604]: Intel Corporation Cannon Lake PCH PCI Express Root Port [8086:a330] (rev f0) (prog-if 00 [Normal decode]) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 126 Bus: primary=00, secondary=3d, subordinate=3d, sec-latency=0 Memory behind bridge: ed200000-ed2fffff Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR- BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B- PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn- Capabilities: <access denied> Kernel driver in use: pcieport 00:1f.0 ISA bridge [0601]: Intel Corporation Device [8086:a30e] (rev 10) Subsystem: Dell Device [1028:087d] Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0 00:1f.3 Audio device [0403]: Intel Corporation Cannon Lake PCH cAVS [8086:a348] (rev 10) (prog-if 80) Subsystem: Dell Cannon Lake PCH cAVS [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 32, Cache Line Size: 64 bytes Interrupt: pin B routed to IRQ 155 Region 0: Memory at ed518000 (64-bit, non-prefetchable) [size=16K] Region 4: Memory at ed100000 (64-bit, non-prefetchable) [size=1M] Capabilities: <access denied> Kernel driver in use: snd_hda_intel Kernel modules: snd_hda_intel 00:1f.4 SMBus [0c05]: Intel Corporation Cannon Lake PCH SMBus Controller [8086:a323] (rev 10) Subsystem: Dell Cannon Lake PCH SMBus Controller [1028:087d] Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx- Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Interrupt: pin A routed to IRQ 16 Region 0: Memory at ed520000 (64-bit, non-prefetchable) [size=256] Region 4: I/O ports at efa0 [size=32] Kernel driver in use: i801_smbus Kernel modules: i2c_i801 00:1f.5 Serial bus controller [0c80]: Intel Corporation Cannon Lake PCH SPI Controller [8086:a324] (rev 10) Subsystem: Dell Cannon Lake PCH SPI Controller [1028:087d] Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Region 0: Memory at fe010000 (32-bit, non-prefetchable) [size=4K] 01:00.0 3D controller [0302]: NVIDIA Corporation GP107GLM [Quadro P2000 Mobile] [10de:1cba] (rev ff) (prog-if ff) !!! Unknown header type 7f Kernel modules: nvidia 3b:00.0 Network controller [0280]: Intel Corporation Wireless-AC 9260 [8086:2526] (rev 29) Subsystem: Intel Corporation Wireless-AC 9260 [8086:4010] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 Region 0: Memory at ed400000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: iwlwifi Kernel modules: iwlwifi 3c:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS525A PCI Express Card Reader [10ec:525a] (rev 01) Subsystem: Dell RTS525A PCI Express Card Reader [1028:087d] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 127 Region 1: Memory at ed300000 (32-bit, non-prefetchable) [size=4K] Capabilities: <access denied> Kernel driver in use: rtsx_pci Kernel modules: rtsx_pci 3d:00.0 Non-Volatile memory controller [0108]: Toshiba America Info Systems Device [1179:0116] (prog-if 02 [NVM Express]) Subsystem: Toshiba America Info Systems Device [1179:0001] Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+ Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx- Latency: 0, Cache Line Size: 64 bytes Interrupt: pin A routed to IRQ 16 NUMA node: 0 Region 0: Memory at ed200000 (64-bit, non-prefetchable) [size=16K] Capabilities: <access denied> Kernel driver in use: nvme Kernel modules: nvme ** USB devices: Bus 002 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub Bus 001 Device 004: ID 046d:c08b Logitech, Inc. Bus 001 Device 003: ID 0c45:671d Microdia Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub -- System Information: Debian Release: 10.6 APT prefers stable APT policy: (990, 'stable'), (500, 'proposed-updates'), (90, 'testing'), (70, 'unstable') Architecture: amd64 (x86_64) Foreign Architectures: i386 Kernel: Linux 4.19.0-10-amd64 (SMP w/12 CPU cores) Kernel taint flags: TAINT_OOT_MODULE, TAINT_UNSIGNED_MODULE Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.utf8 (charmap=UTF-8), LANGUAGE=en_US:en (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Init: systemd (via /run/systemd/system) LSM: AppArmor: enabled Versions of packages linux-image-4.19.0-12-amd64 depends on: ii initramfs-tools [linux-initramfs-tool] 0.133+deb10u1 ii kmod 26-1 ii linux-base 4.6 Versions of packages linux-image-4.19.0-12-amd64 recommends: ii apparmor 2.13.2-10 ii firmware-linux-free 3.4 Versions of packages linux-image-4.19.0-12-amd64 suggests: pn debian-kernel-handbook <none> ii extlinux 3:6.04~git20190206.bf6db5b4+dfsg1-1 ii grub-efi-amd64 2.02+dfsg1-20+deb10u2 pn linux-doc-4.19 <none> Versions of packages linux-image-4.19.0-12-amd64 is related to: ii firmware-amd-graphics 20190114-2 pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-cavium <none> pn firmware-intel-sound <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> ii firmware-iwlwifi 20190114-2 pn firmware-libertas <none> ii firmware-linux-nonfree 20190114-2 ii firmware-misc-nonfree 20190114-2 pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-realtek <none> pn firmware-samsung <none> pn firmware-siano <none> pn firmware-ti-connectivity <none> pn xen-hypervisor <none> -- no debconf information
--- End Message ---
--- Begin Message ---
- To: 974939-done@bugs.debian.org
- Subject: Re: Bug#974939: machine does not boot
- From: Ben Hutchings <ben@decadent.org.uk>
- Date: Mon, 23 Nov 2020 10:41:25 +0000
- Message-id: <0b90a840471d86834671e45cc6294e4d5f1bf953.camel@decadent.org.uk>
- In-reply-to: <[🔎] 20201123102617.GB4450@laptop-t.office.oeko.net>
- References: <[🔎] 160555566531.21662.12288989478279065715.reportbug@laptop-t.office.oeko.net> <[🔎] deeeec269a6ccb0ddc19f1b1a222e669843e98c8.camel@decadent.org.uk> <[🔎] 20201123100449.GA4450@laptop-t.office.oeko.net> <[🔎] 765d1fea8e011f5fef9dec5a6d19d8275cee8420.camel@decadent.org.uk> <[🔎] 20201123102617.GB4450@laptop-t.office.oeko.net>
On Mon, 2020-11-23 at 10:26 +0000, Toni Mueller wrote: > Hi Ben, > > On Mon, Nov 23, 2020 at 10:12:01AM +0000, Ben Hutchings wrote: > > On Mon, 2020-11-23 at 10:04 +0000, Toni Mueller wrote: > > > I agree, but I can only file a bug report against the kernel package. > > > Please find the output of this command attached. > > cryptsetup support is not included in the newer initramfs images. > > I saw that, but was not aware of this package: > > > Did you remove cryptsetup-initramfs by accident? > > Not that I am aware of, and definitely not intentionally. Until now, I > had no idea that it even existed. But I can now see that it was removed > in a dist-upgrade run on the 9th of May last year (huh?!?). But there > seems to be a problem to re-install it: I recommend that you always check the list of packages to be removed in a dist-upgrade, if you have some packages installed from testing/unstable. > # apt install cryptsetup-initramfs -y > > ... > > The following packages will be REMOVED: > libgcc-s1 > The following NEW packages will be installed: > cryptsetup-initramfs > WARNING: The following essential packages will be removed. > This should NOT be done unless you know exactly what you are doing! > libgcc-s1 > 0 upgraded, 1 newly installed, 1 to remove and 2 not upgraded. > E: Essential packages were removed and -y was used without --allow-remove-essential. > > > > Since libgcc-s1 is being provided by libgcc1, I am inclined to run with > --allow-remove-essential. But this is still quite scary! > > (I wasn't aware of libgcc-s1, either. :( ) It doesn't exist in stable. Perhaps you installed something from testing/unstable that required it? libgcc-s1 breaks the stable version of cryptsetup-initramfs. Ben. -- Ben Hutchings For every complex problem there is a solution that is simple, neat, and wrong.Attachment: signature.asc
Description: This is a digitally signed message part
--- End Message ---