Bug#696505: linux-image-3.2.0-4-amd64: saa7146 based DVB-C card causes repeated error messages
Package: src:linux
Version: 3.2.32-1
Severity: normal
Dear Maintainer,
I have some problems getting my system running stable after upgrading it to wheezy.
My system is used as a vdr and is equipped with multiple DVB cards.
It seems that the 2 installed Terratec Cinergy 1200 DVB-C (saa-7146) cards cause some problems when running an actual kernel.
The same system including these DVB cards is running stable with Squeeze on a homebrew 2.6.33 kernel with extra DVB drivers (dvb-s2api-liplianin-0~2010-06-11.hg15345)
When booting wheezy – system usually comes up ok
all DVB cards are usable until programs like update-grub2 are executed (seems like it has to do with HDD access) .
Often while update-grub2 is detecting the other installations the system starts showing error messages like:
[ 528.416023] DVB: TDA10023(3): tda10023_readreg: readreg error (reg == 0x1c, ret == -1)
[ 528.428071] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 528.428081] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 528.428088] saa7146: interrupt_hw: disabling interrupt source(s)!
I tried to compile and install a new kernel (3.7.1)- but I could not see any change compared to the installed debian kernel.
I also tried a similar kernel (2.6.33 ) and driver combination than the one in used by my squeeze installation. I could not reproduce the error but did not succeed getting all hardware running.
After removing the two Cinergy (saa-7146) cards from the system I could not reproduce the problem anymore.
p_body
-- Package-specific info:
** Version:
Linux version 3.2.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-12) ) #1 SMP Debian 3.2.32-1
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-4-amd64 root=UUID=c361d309-f014-460d-aa29-63cb9a8fa73d ro irqpoll
** Tainted: PO (4097)
* Proprietary module has been loaded.
* Out-of-tree module has been loaded.
** Kernel log:
[ 1780.518620] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.538602] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.538610] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.538618] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.558602] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.558611] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.558619] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.578603] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.578612] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.578620] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.598601] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.598610] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.598617] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.618601] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.618610] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.618618] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.638600] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.638609] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.638618] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.658603] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.658611] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.658619] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.678600] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.678609] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.678616] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.698597] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.698606] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.698614] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.718596] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.718606] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.718613] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.738600] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.738609] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.738616] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.758599] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.758608] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.758616] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.778597] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.778605] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.778613] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.798596] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.798605] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.798613] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.818596] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.818605] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.818612] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.838607] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.838616] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.838624] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.858598] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.858607] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.858615] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.878596] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.878604] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.878612] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.898596] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.898605] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.898612] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.918595] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.918604] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.918611] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.937767] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.937776] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.937784] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.938589] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.938597] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.938605] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.958596] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.958604] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.958612] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.972835] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.972844] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.972851] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.978593] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.978601] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.978609] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1780.998594] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1780.998602] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1780.998610] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.018599] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.018607] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.018615] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.038638] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.038652] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.038659] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.058657] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.058672] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.058680] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.078650] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.078665] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.078673] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.098654] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.098670] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.098678] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.118654] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.118669] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.118677] saa7146: interrupt_hw: disabling interrupt source(s)!
[ 1781.138645] saa7146: saa7146 (1): unexpected i2c irq: isr e7fffbff psr ffffffff ssr ffffffff
[ 1781.138660] saa7146: interrupt_hw: warning: interrupt enabled, but not handled properly.(0xe7fcfbff)
[ 1781.138668] saa7146: interrupt_hw: disabling interrupt source(s)!
** Model information
sys_vendor: System manufacturer
product_name: System Product Name
product_version: System Version
chassis_vendor: Chassis Manufacture
chassis_version: Chassis Version
bios_vendor: American Megatrends Inc.
bios_version: 1303
board_vendor: ASUSTeK Computer INC.
board_name: M4N78 PRO
board_version: Rev 1.xx
** Loaded modules:
ngene
budget_av
budget_core
videobuf_dvb
dvb_core
fuse
btrfs
crc32c
libcrc32c
zlib_deflate
ufs
qnx4
hfsplus
hfs
minix
ntfs
vfat
msdos
fat
jfs
xfs
reiserfs
ext2
dm_mod
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
ext3
jbd
loop
isl6421
cx24116
cx88_vp3054_i2c
rc_hauppauge
tuner
snd_hda_codec_hdmi
snd_hda_codec_via
tda10023
stv6110x
nvidia(P)
lnbp21
cx8800
cx88_alsa
cx8802
ttpci_eeprom
cx88xx
saa7146_vv
ir_lirc_codec
lirc_dev
btcx_risc
stv090x
snd_hda_intel
ir_mce_kbd_decoder
saa7146
ir_sony_decoder
tveeprom
videobuf_dma_sg
videobuf_core
v4l2_common
snd_hda_codec
snd_seq
ir_jvc_decoder
snd_hwdep
joydev
snd_pcm
videodev
snd_seq_device
snd_page_alloc
ir_rc6_decoder
rc_imon_pad
ir_rc5_decoder
usbhid
hid
v4l2_compat_ioctl32
pcspkr
snd_timer
k8temp
imon
ir_nec_decoder
rc_medion_x10
media
powernow_k8
evdev
i2c_algo_bit
i2c_nforce2
psmouse
i2c_core
edac_mce_amd
mperf
video
serio_raw
edac_core
shpchp
asus_atk0110
wmi
ati_remote
rc_core
snd
button
processor
thermal_sys
soundcore
ext4
crc16
jbd2
mbcache
sr_mod
cdrom
sg
sd_mod
crc_t10dif
ata_generic
floppy
ohci_hcd
ahci
libahci
pata_amd
ehci_hcd
libata
scsi_mod
forcedeth
usbcore
usb_common
** PCI devices:
00:00.0 RAM memory [0500]: NVIDIA Corporation MCP78S [GeForce 8200] Memory Controller [10de:0754] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 ISA bridge [0601]: NVIDIA Corporation MCP78S [GeForce 8200] LPC Bridge [10de:075c] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: I/O ports at 2f00 [size=256]
00:01.1 SMBus [0c05]: NVIDIA Corporation MCP78S [GeForce 8200] SMBus [10de:0752] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 2900 [size=64]
Region 4: I/O ports at 2d00 [size=64]
Region 5: I/O ports at 2e00 [size=64]
Capabilities: <access denied>
Kernel driver in use: nForce2_smbus
00:01.2 RAM memory [0500]: NVIDIA Corporation MCP78S [GeForce 8200] Memory Controller [10de:0751] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.3 Co-processor [0b40]: NVIDIA Corporation MCP78S [GeForce 8200] Co-Processor [10de:0753] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 7
Region 0: Memory at f3f80000 (32-bit, non-prefetchable) [size=512K]
00:01.4 RAM memory [0500]: NVIDIA Corporation MCP78S [GeForce 8200] Memory Controller [10de:0568] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:02.0 USB controller [0c03]: NVIDIA Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller [10de:077b] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f3f7e000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:02.1 USB controller [0c03]: NVIDIA Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller [10de:077c] (rev a1) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at f3f7fc00 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 USB controller [0c03]: NVIDIA Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller [10de:077d] (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f3f7d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
00:04.1 USB controller [0c03]: NVIDIA Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller [10de:077e] (rev a1) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at f3f7f800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:06.0 IDE interface [0101]: NVIDIA Corporation MCP78S [GeForce 8200] IDE [10de:0759] (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_amd
00:07.0 Audio device [0403]: NVIDIA Corporation MCP72XE/MCP72P/MCP78U/MCP78S High Definition Audio [10de:0774] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:836c]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at f3f78000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:08.0 PCI bridge [0604]: NVIDIA Corporation MCP78S [GeForce 8200] PCI Bridge [10de:075a] (rev a1) (prog-if 01 [Subtractive decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
Memory behind bridge: f4000000-f8efffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat+ DiscTmrSERREn-
Capabilities: <access denied>
00:09.0 IDE interface [0101]: NVIDIA Corporation MCP78S [GeForce 8200] SATA Controller (non-AHCI mode) [10de:0ad0] (rev a2) (prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at c480 [size=8]
Region 1: I/O ports at c400 [size=4]
Region 2: I/O ports at c080 [size=8]
Region 3: I/O ports at c000 [size=4]
Region 4: I/O ports at bc00 [size=16]
Region 5: Memory at f3f76000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:0a.0 Ethernet controller [0200]: NVIDIA Corporation MCP77 Ethernet [10de:0760] (rev a2)
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 42
Region 0: Memory at f3f7c000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at b880 [size=8]
Region 2: Memory at f3f7f400 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at f3f7f000 (32-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: forcedeth
00:0b.0 PCI bridge [0604]: NVIDIA Corporation MCP78S [GeForce 8200] PCI Express Bridge [10de:0569] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f8f00000-f9ffffff
Prefetchable memory behind bridge: 00000000c8000000-00000000d5ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:10.0 PCI bridge [0604]: NVIDIA Corporation MCP78S [GeForce 8200] PCI Express Bridge [10de:0778] (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fa000000-fbefffff
Prefetchable memory behind bridge: 00000000d6000000-00000000dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:13.0 PCI bridge [0604]: NVIDIA Corporation MCP78S [GeForce 8200] PCI Bridge [10de:077a] (rev a1) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Memory behind bridge: fbf00000-fbffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:14.0 PCI bridge [0604]: NVIDIA Corporation MCP78S [GeForce 8200] PCI Bridge [10de:077a] (rev a1) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
Kernel driver in use: k8temp
01:05.0 Multimedia video controller [0400]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [14f1:8800] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: cx8800
01:05.1 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [Audio Port] [14f1:8811] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: cx88_audio
01:05.2 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [MPEG Port] [14f1:8802] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: cx88-mpeg driver manager
01:05.4 Multimedia controller [0480]: Conexant Systems, Inc. CX23880/1/2/3 PCI Video and Audio Decoder [IR Port] [14f1:8804] (rev ff) (prog-if ff)
!!! Unknown header type 7f
01:06.0 Multimedia controller [0480]: Philips Semiconductors SAA7146 [1131:7146] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: budget_av
01:07.0 Multimedia controller [0480]: Philips Semiconductors SAA7146 [1131:7146] (rev ff) (prog-if ff)
!!! Unknown header type 7f
Kernel driver in use: budget_av
02:00.0 VGA compatible controller [0300]: NVIDIA Corporation C77 [GeForce 8300] [10de:0848] (rev a2) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:82e2]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f9000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at d4000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at dc00 [size=128]
[virtual] Expansion ROM at f8fe0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: nvidia
03:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF119 [GeForce GT 520] [10de:1040] (rev a1) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:83a0]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fa000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d8000000 (64-bit, prefetchable) [size=128M]
Region 3: Memory at d6000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at ec00 [size=128]
[virtual] Expansion ROM at fbe00000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nvidia
03:00.1 Audio device [0403]: NVIDIA Corporation GF119 HDMI Audio Controller [10de:0e08] (rev a1)
Subsystem: ASUSTeK Computer Inc. Device [1043:83a0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at fbefc000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
04:00.0 Multimedia video controller [0400]: Micronas Semiconductor Holding AG nGene PCI-Express Multimedia Controller [18c3:0720] (rev ff) (prog-if ff)
!!! Unknown header type 7f
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 002: ID 0bc7:0006 X10 Wireless Technology, Inc. Wireless Transceiver (ACPI-compliant)
Bus 003 Device 002: ID 046d:0b02 Logitech, Inc. BT Mini-Receiver (HID proxy mode)
Bus 003 Device 003: ID 15c2:0034 SoundGraph Inc.
Bus 003 Device 004: ID 04d9:1400 Holtek Semiconductor, Inc. PS/2 keyboard + mouse controller
Bus 003 Device 005: ID 046d:c70e Logitech, Inc. MX1000 Bluetooth Laser Mouse
Bus 003 Device 006: ID 046d:c70a Logitech, Inc. MX5000 Cordless Desktop
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (600, 'testing')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-4-amd64 (SMP w/2 CPU cores)
Locale: LANG=de_DE.UTF-8, LC_CTYPE=de_DE.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.46
ii initramfs-tools [linux-initramfs-tool] 0.109
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-4-amd64 recommends:
pn firmware-linux-free <none>
Versions of packages linux-image-3.2.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 1.99-23.1
pn linux-doc-3.2 <none>
Versions of packages linux-image-3.2.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-4-amd64/postinst/depmod-error-initrd-3.2.0-4-amd64: false
linux-image-3.2.0-4-amd64/prerm/removing-running-kernel-3.2.0-4-amd64: true
linux-image-3.2.0-4-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-4-amd64/postinst/missing-firmware-3.2.0-4-amd64:
Reply to: