Package: src:linux Version: 3.5-1~experimental.1 Severity: normal Usertags: pca.it-boot Hi there! The Samsung NP-Q1u [1] has on-device (slightly difficult for everyday usage) and USB-external keyboards. Starting from 3.5-1~experimental.1 this latter is no more available at the cryptsetup prompt, while it works as expected in GRUB-2 and GNOME-3. [1] <http://bugs.debian.org/682737> The same behavior happens with 3.5.2-1~experimental.1, but it did not with 3.4.4-1~experimental.1 or 3.2.23-1. However, the differences in the initrd content does not seem relevant: --8<---------------cut here---------------start------------->8--- --- initrd.img-3.4-trunk-686-pae_files.find.sed 2012-09-11 16:08:21.960755897 +0200 +++ initrd.img-3.5-trunk-686-pae_files.find.sed 2012-09-11 16:08:09.800695591 +0200 @@ -140,9 +140,11 @@ ./usr/share/plymouth/themes/joy/background.png ./usr/share/plymouth/themes/joy/progress_dot_off.png ./usr/share/plymouth/themes/joy/debian_logo.png +./usr/share/plymouth/themes/joy/password_dot16.png ./usr/share/plymouth/themes/joy/joy.plymouth ./usr/share/plymouth/themes/joy/password_field.png ./usr/share/plymouth/themes/joy/progress_dot_off16.png +./usr/share/plymouth/themes/joy/password_dot.png ./usr/share/plymouth/debian-logo.png ./usr/share/plymouth/plymouthd.defaults ./usr/share/fonts @@ -543,6 +545,7 @@ ./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/team/team.ko ./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/team/team_mode_activebackup.ko ./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/team/team_mode_roundrobin.ko +./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/team/team_mode_loadbalance.ko ./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/phy ./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/phy/lxt.ko ./lib/modules/linuxtrunk-686-pae/kernel/drivers/net/phy/micrel.ko @@ -824,8 +827,6 @@ ./lib/modules/linuxtrunk-686-pae/kernel/drivers/ssb/ssb.ko ./lib/modules/linuxtrunk-686-pae/kernel/drivers/thermal ./lib/modules/linuxtrunk-686-pae/kernel/drivers/thermal/thermal_sys.ko -./lib/modules/linuxtrunk-686-pae/kernel/drivers/power -./lib/modules/linuxtrunk-686-pae/kernel/drivers/power/power_supply.ko ./lib/modules/linuxtrunk-686-pae/kernel/drivers/misc ./lib/modules/linuxtrunk-686-pae/kernel/drivers/misc/cb710 ./lib/modules/linuxtrunk-686-pae/kernel/drivers/misc/cb710/cb710.ko --8<---------------cut here---------------end--------------->8--- --8<---------------cut here---------------start------------->8--- diff -Naur initrd.img-3.4-trunk-686-pae_files/conf/modules initrd.img-3.5-trunk-686-pae_files/conf/modules --- initrd.img-3.4-trunk-686-pae_files/conf/modules 2012-09-11 16:04:11.035511620 +0200 +++ initrd.img-3.5-trunk-686-pae_files/conf/modules 2012-09-11 15:58:24.825794859 +0200 @@ -1,2 +1 @@ i915 modeset=1 -unix diff -Naur initrd.img-3.4-trunk-686-pae_files/etc/udev/udev.conf initrd.img-3.5-trunk-686-pae_files/etc/udev/udev.conf --- initrd.img-3.4-trunk-686-pae_files/etc/udev/udev.conf 2012-09-11 16:04:11.031511607 +0200 +++ initrd.img-3.5-trunk-686-pae_files/etc/udev/udev.conf 2012-09-11 15:58:24.821794836 +0200 @@ -1,4 +1,7 @@ # The initial syslog(3) priority: "err", "info", "debug" or its # numerical equivalent. For runtime debugging, the daemons internal # state can be changed with: "udevadm control --log-priority=<value>". +# +# udevd is started in the initramfs, so when this file is modified the +# initramfs should be rebuilt. udev_log="err" --8<---------------cut here---------------end--------------->8--- I also tried to add usbhid to /etc/initramfs-tools/modules, but nothing changed. Any ideas? Thx, bye, Gismo / Luca -- Package-specific info:
** Version:
Linux version 3.5-trunk-686-pae (Debian 3.5-1~experimental.1) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-8) ) #1 SMP Thu Aug 2 17:56:18 UTC 2012
** Command line:
BOOT_IMAGE=/vmlinuz-3.5-trunk-686-pae root=/dev/mapper/kappei-root ro quiet splash
** Not tainted
** Kernel log:
[ 47.551797] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: (null)
[ 50.917672] udevd[381]: starting version 175
[ 52.377713] ACPI: AC Adapter [ADP1] (off-line)
[ 52.395135] ACPI: Requesting acpi_cpufreq
[ 52.397318] ACPI: Battery Slot [BAT1] (battery present)
[ 52.406151] Marking TSC unstable due to TSC halts in idle
[ 52.406185] ACPI: acpi_idle registered with cpuidle
[ 52.427336] Switching to clocksource hpet
[ 52.789087] input: PC Speaker as /devices/platform/pcspkr/input/input5
[ 53.758238] cfg80211: Calling CRDA to update world regulatory domain
[ 53.791360] Bluetooth: Core ver 2.16
[ 53.791416] NET: Registered protocol family 31
[ 53.791422] Bluetooth: HCI device and connection manager initialized
[ 53.791910] Bluetooth: HCI socket layer initialized
[ 53.791917] Bluetooth: L2CAP socket layer initialized
[ 53.791931] Bluetooth: SCO socket layer initialized
[ 53.806275] ACPI Warning: 0x000018a0-0x000018bf SystemIO conflicts with Region \_SB_.PCI0.SBUS.SMBI 1 (20120320/utaddress-251)
[ 53.806295] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 53.909047] microcode: CPU0 sig=0x6d8, pf=0x8, revision=0x21
[ 54.139036] intel_rng: FWH not detected
[ 54.143697] input: PS/2 Generic Mouse as /devices/platform/i8042/serio4/input/input6
[ 54.197159] ACPI Warning: 0x00001060-0x0000107f SystemIO conflicts with Region \PMIO 1 (20120320/utaddress-251)
[ 54.197186] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 54.197195] lpc_ich: Resource conflict(s) found affecting iTCO_wdt
[ 54.197203] ACPI Warning: 0x00001028-0x0000102f SystemIO conflicts with Region \PMIO 1 (20120320/utaddress-251)
[ 54.197221] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 54.197230] ACPI Warning: 0x00001180-0x000011bf SystemIO conflicts with Region \GPIO 1 (20120320/utaddress-251)
[ 54.197248] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 54.197255] lpc_ich: Resource conflict(s) found affecting gpio_ich
[ 54.298867] usbcore: registered new interface driver btusb
[ 54.427395] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 54.676686] snd_hda_intel 0000:00:1b.0: irq 41 for MSI/MSI-X
[ 54.776337] leds_ss4200: no LED devices found
[ 54.831262] ath5k 0000:01:00.0: registered as 'phy0'
[ 55.195267] input: Touchkit Touch as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input7
[ 55.199648] input: Touchkit Touch as /devices/pci0000:00/0000:00:1d.1/usb3/3-1/3-1:1.0/input/input8
[ 55.200489] hid-generic 0003:0EEF:0001.0001: input,hidraw0: USB HID v1.12 Pointer [Touchkit Touch] on usb-0000:00:1d.1-1/input0
[ 55.210705] input: HDA Digital PCBeep as /devices/pci0000:00/0000:00:1b.0/input/input10
[ 55.218912] input: HID 070a:0025 as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.2/2-2.2:1.0/input/input9
[ 55.231984] hid-generic 0003:070A:0025.000B: input,hidraw1: USB HID v1.00 Mouse [HID 070a:0025] on usb-0000:00:1d.0-2.2/input0
[ 55.239234] input: HDA Intel Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card0/input12
[ 55.239839] input: HID 070a:0025 as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.4/2-2.4:1.0/input/input11
[ 55.253028] hid-generic 0003:070A:0025.000C: input,hidraw2: USB HID v1.10 Keyboard [HID 070a:0025] on usb-0000:00:1d.0-2.4/input0
[ 55.275016] input: HID 070a:0025 as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2.4/2-2.4:1.1/input/input13
[ 55.275379] hid-generic 0003:070A:0025.000D: input,hiddev0,hidraw3: USB HID v1.10 Device [HID 070a:0025] on usb-0000:00:1d.0-2.4/input1
[ 55.407731] usbcore: registered new interface driver usbserial
[ 55.408501] usbcore: registered new interface driver usbserial_generic
[ 55.409193] USB Serial support registered for generic
[ 55.409220] usbserial: USB Serial Driver core
[ 55.483813] usbcore: registered new interface driver option
[ 55.484687] USB Serial support registered for GSM modem (1-port)
[ 55.485822] option 1-8.3:1.0: GSM modem (1-port) converter detected
[ 55.486357] usb 1-8.3: GSM modem (1-port) converter now attached to ttyUSB0
[ 55.486426] option 1-8.3:1.1: GSM modem (1-port) converter detected
[ 55.489506] usb 1-8.3: GSM modem (1-port) converter now attached to ttyUSB1
[ 55.491734] option 1-8.3:1.2: GSM modem (1-port) converter detected
[ 55.492352] usb 1-8.3: GSM modem (1-port) converter now attached to ttyUSB2
[ 55.686563] ath: EEPROM regdomain: 0x65
[ 55.686572] ath: EEPROM indicates we should expect a direct regpair map
[ 55.686580] ath: Country alpha2 being used: 00
[ 55.686585] ath: Regpair used: 0x65
[ 55.747697] Linux media interface: v0.10
[ 55.783666] Linux video capture interface: v2.00
[ 55.905073] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 55.905861] ath5k: phy0: Atheros AR5414 chip found (MAC: 0xa0, PHY: 0x61)
[ 56.196762] gspca_main: v2.14.0 registered
[ 56.286532] gspca_main: vc032x-2.14.0 probing 0ac8:c301
[ 56.400276] gspca_vc032x: Unknown sensor...
[ 56.400314] vc032x: probe of 1-8.2:1.0 failed with error -22
[ 56.401266] usbcore: registered new interface driver vc032x
[ 57.614914] cfg80211: World regulatory domain updated:
[ 57.614927] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 57.614938] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 57.614948] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 57.614957] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 57.614966] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 57.614976] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 59.600417] EXT4-fs (dm-2): re-mounted. Opts: (null)
[ 60.098349] EXT4-fs (dm-2): re-mounted. Opts: errors=remount-ro
[ 60.522794] loop: module loaded
[ 62.389965] Adding 2928636k swap on /dev/mapper/kappei-swap. Priority:-1 extents:1 across:2928636k
[ 65.502693] RPC: Registered named UNIX socket transport module.
[ 65.502703] RPC: Registered udp transport module.
[ 65.502707] RPC: Registered tcp transport module.
[ 65.502712] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 65.589960] FS-Cache: Loaded
[ 65.733414] NFS: Registering the id_resolver key type
[ 65.733447] Key type id_resolver registered
[ 65.733472] FS-Cache: Netfs 'nfs' registered for caching
[ 65.776271] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 75.216274] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 75.462190] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input14
[ 76.057501] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 82.034633] Bluetooth: RFCOMM TTY layer initialized
[ 82.034651] Bluetooth: RFCOMM socket layer initialized
[ 82.034657] Bluetooth: RFCOMM ver 1.11
[ 82.090477] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 82.090486] Bluetooth: BNEP filters: protocol multicast
[ 83.515304] lp: driver loaded but no devices found
[ 83.551336] ppdev: user-space parallel port driver
** Model information
not available
** Loaded modules:
parport_pc
ppdev
lp
parport
bnep
rfcomm
binfmt_misc
uinput
nfsd
nfs
nfs_acl
auth_rpcgss
fscache
lockd
sunrpc
ext2
loop
gspca_vc032x
gspca_main
arc4
videodev
media
option
usb_wwan
usbserial
joydev
snd_hda_codec_realtek
hid_generic
ath5k
ath
snd_hda_intel
mac80211
snd_hda_codec
snd_hwdep
btusb
lpc_ich
mfd_core
snd_pcm
snd_page_alloc
microcode
i2c_i801
bluetooth
cfg80211
snd_seq
snd_seq_device
rng_core
snd_timer
snd
soundcore
rfkill
acpi_cpufreq
psmouse
serio_raw
pcspkr
mperf
processor
battery
ac
evdev
ext4
crc16
jbd2
mbcache
sha256_generic
cryptd
aes_i586
aes_generic
cbc
dm_crypt
dm_mod
usbhid
hid
sd_mod
crc_t10dif
ata_generic
ata_piix
libata
b44
ssb
mmc_core
scsi_mod
mii
pcmcia
pcmcia_core
i915
uhci_hcd
fan
i2c_algo_bit
video
thermal
drm_kms_helper
ehci_hcd
drm
usbcore
button
usb_common
i2c_core
thermal_sys
** Network interface configuration:
auto lo
iface lo inet loopback
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN qlen 1000
link/ether 00:13:77:68:37:90 brd ff:ff:ff:ff:ff:ff
3: wlan0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc mq state DOWN qlen 1000
link/ether 00:1b:9e:70:ab:30 brd ff:ff:ff:ff:ff:ff
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
wlan0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
lo: 1184 16 0 0 0 0 0 0 1184 16 0 0 0 0 0 0
eth0: 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
*** Protocol statistics:
Ip:
16 total packets received
0 forwarded
0 incoming packets discarded
16 incoming packets delivered
16 requests sent out
8 outgoing packets dropped
8 dropped because of missing route
Icmp:
8 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
destination unreachable: 8
8 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 8
IcmpMsg:
InType3: 8
OutType3: 8
Tcp:
0 active connections openings
0 passive connection openings
0 failed connection attempts
0 connection resets received
0 connections established
0 segments received
0 segments send out
0 segments retransmited
0 bad segments received.
0 resets sent
Udp:
0 packets received
8 packets to unknown port received.
0 packet receive errors
8 packets sent
UdpLite:
TcpExt:
0 packet headers predicted
IpExt:
InOctets: 1184
OutOctets: 1184
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express Memory Controller Hub [8086:27a0] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation Mobile 945GM/PM/GMS, 943/940GML and 945GT Express PCI Express Root Port [8086:27a1] (rev 03) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f0100000-f01fffff
Prefetchable memory behind bridge: 0000000040000000-00000000401fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GM/GMS, 943/940GML Express Integrated Graphics Controller [8086:27a2] (rev 03) (prog-if 00 [VGA controller])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at 1800 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f0300000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f0080000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation N10/ICH 7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: Memory at f0340000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1d.0 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at 1820 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 1840 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at 1860 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at 1880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation N10/ICH 7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f0544000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=02, sec-latency=32
Memory behind bridge: f0200000-f02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.1 IDE interface [0101]: Intel Corporation 82801G (ICH7 Family) IDE Controller [8086:27df] (rev 02) (prog-if 8a [Master SecP PriP])
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1810 [size=16]
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation N10/ICH 7 Family SMBus Controller [8086:27da] (rev 02)
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 18a0 [size=32]
01:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x / AR542x Wireless Network Adapter (PCI-Express) [168c:001c] (rev 01)
Subsystem: Askey Computer Corp. Device [144f:7108]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f0100000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k
02:05.0 Ethernet controller [0200]: Broadcom Corporation BCM4401-B0 100Base-TX [14e4:170c] (rev 02)
Subsystem: Samsung Electronics Co Ltd Device [144d:c032]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 22
Region 0: Memory at f0200000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: b44
** USB devices:
Bus 001 Device 005: ID 144d:c032
Bus 002 Device 011: ID 058f:9254 Alcor Micro Corp. Hub
Bus 003 Device 002: ID 0eef:0001 D-WAV Scientific Co., Ltd eGalax TouchScreen
Bus 004 Device 002: ID 0a5c:2101 Broadcom Corp. BCM2045 Bluetooth
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 006: ID 0ac8:c301 Z-Star Microelectronics Corp.
Bus 001 Device 007: ID 0af0:6901 Option
Bus 002 Device 012: ID 070a:0025 Oki Electric Industry Co., Ltd
Bus 002 Device 013: ID 070a:0025 Oki Electric Industry Co., Ltd
-- System Information: Debian Release: wheezy/sid APT prefers testing APT policy: (500, 'testing') Architecture: i386 (i686) Kernel: Linux 3.5-trunk-686-pae (SMP w/1 CPU core) Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8) Shell: /bin/sh linked to /bin/dash Versions of packages linux-image-3.5-trunk-686-pae depends on: ii debconf [debconf-2.0] 1.5.44 ii initramfs-tools [linux-initramfs-tool] 0.107 ii kmod 8-2 ii linux-base 3.5 ii module-init-tools 8-2 Versions of packages linux-image-3.5-trunk-686-pae recommends: pn firmware-linux-free <none> ii libc6-i686 2.13-33 Versions of packages linux-image-3.5-trunk-686-pae suggests: pn debian-kernel-handbook <none> ii grub-pc 1.99-22.1 pn linux-doc-3.5 <none> Versions of packages linux-image-3.5-trunk-686-pae is related to: pn firmware-atheros <none> pn firmware-bnx2 <none> pn firmware-bnx2x <none> pn firmware-brcm80211 <none> pn firmware-intelwimax <none> pn firmware-ipw2x00 <none> pn firmware-ivtv <none> pn firmware-iwlwifi <none> pn firmware-libertas <none> pn firmware-linux <none> pn firmware-linux-nonfree <none> pn firmware-myricom <none> pn firmware-netxen <none> pn firmware-qlogic <none> pn firmware-ralink <none> pn firmware-realtek <none> pn xen-hypervisor <none> -- debconf information: linux-image-3.5-trunk-686-pae/prerm/removing-running-kernel-3.5-trunk-686-pae: true linux-image-3.5-trunk-686-pae/postinst/depmod-error-initrd-3.5-trunk-686-pae: false linux-image-3.5-trunk-686-pae/postinst/ignoring-ramdisk: linux-image-3.5-trunk-686-pae/postinst/missing-firmware-3.5-trunk-686-pae:
Attachment:
pgpHnkbXfOBXM.pgp
Description: PGP signature