Bug#648766: [sparc] BUG: NMI Watchdog detected LOCKUP on CPU0
I am right now testing one major kernel version at a time, and on the
3.0.0-1 I got an interesting error when I ran my brutality test on the
system.
"sd 0:0:0:0: ABORT operation complete."
I wonder if this is some symptom of the problem as well. It canceled the
cat /dev/sda > /dev/null process on a segfault after this error popped
up. I have included the entire output from dmesg. Still looking for the
kernel version that causes the panic.
On 04/05/2012 11:00 PM, Jonathan Nieder wrote:
found 648766 linux-2.6/3.2.13-1
found 648766 linux-2.6/3.2.14-1
# 3.3.1
found 648766 linux-2.6/3.3-1~experimental.1
tags 648766 + upstream
quit
Kieron Gillespie wrote:
Now with that said I can't seem to crash the 2.6.32 kernel in the
same way with SMP off, haven't tried with SMP on yet, but I have a
feeling that will work fine as well. So this seems like it's some
sort of regression in the linux kernel.
Thanks, Kieron. Just for reference: if you want to bisect through
pre-compiled kernels to narrow down which version introduced trouble,
you can find some at<http://snapshot.debian.org/package/linux-2.6/>.
Ciao,
Jonathan
[ 0.000000] PROMLIB: Sun IEEE Boot Prom 'OBP 4.9.7 2004/05/27 07:31'
[ 0.000000] PROMLIB: Root node compatible:
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.0.0 (root@BigRed) (gcc version 4.4.5 (Debian 4.4.5-8) ) #1 SMP Fri Apr 6 00:19:17 EDT 2012
[ 0.000000] bootconsole [earlyprom0] enabled
[ 0.000000] ARCH: SUN4U
[ 0.000000] Ethernet address: 00:03:ba:44:d1:39
[ 0.000000] Kernel: Using 2 locked TLB entries for main kernel image.
[ 0.000000] Remapping the kernel... done.
[ 0.000000] OF stdout device is: /pci@1f,700000/SUNW,XVR-600@2
[ 0.000000] PROM: Built device tree with 95808 bytes of memory.
[ 0.000000] Top of RAM: 0x121feb2000, Total RAM: 0x3fd8e000
[ 0.000000] Memory hole size: 73217MB
[ 0.000000] [0000010004000000-fffff80200400000] page_structs=131072 node=0 entry=16/8192
[ 0.000000] [0000010004000000-fffff80200800000] page_structs=131072 node=0 entry=17/8192
[ 0.000000] [0000010024000000-fffff80200c00000] page_structs=131072 node=0 entry=144/8192
[ 0.000000] [0000010024000000-fffff80201000000] page_structs=131072 node=0 entry=145/8192
[ 0.000000] Zone PFN ranges:
[ 0.000000] Normal 0x00100000 -> 0x0090ff59
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[8] active PFN ranges
[ 0.000000] 0: 0x00100000 -> 0x00110000
[ 0.000000] 0: 0x00900000 -> 0x0090f7ff
[ 0.000000] 0: 0x0090f800 -> 0x0090fe64
[ 0.000000] 0: 0x0090fee6 -> 0x0090feea
[ 0.000000] 0: 0x0090feed -> 0x0090fef1
[ 0.000000] 0: 0x0090fef3 -> 0x0090fef5
[ 0.000000] 0: 0x0090fef7 -> 0x0090ff45
[ 0.000000] 0: 0x0090ff4d -> 0x0090ff59
[ 0.000000] On node 0 totalpages: 130759
[ 0.000000] Normal zone: 66047 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 64712 pages, LIFO batch:15
[ 0.000000] Booting Linux...
[ 0.000000] PERCPU: Embedded 5 pages/cpu @fffff80201400000 s11840 r8192 d20928 u2097152
[ 0.000000] pcpu-alloc: s11840 r8192 d20928 u2097152 alloc=1*4194304
[ 0.000000] pcpu-alloc: [0] 0 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64712
[ 0.000000] Kernel command line: root=/dev/sda2 ro
[ 0.000000] PID hash table entries: 2048 (order: 1, 16384 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 524288 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 262144 bytes)
[ 0.000000] Memory: 1012624k available (3592k kernel code, 1368k data, 224k init) [fffff80000000000,000000121feb2000]
[ 0.000000] SLUB: Genslabs=16, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] CONFIG_RCU_FANOUT set to non-default value of 32
[ 0.000000] NR_IRQS:255
[ 0.000000] clocksource: mult[53555555] shift[24]
[ 0.000000] clockevent: mult[3126e98] shift[32]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 42.069076] Calibrating delay using timer specific routine.. 24.00 BogoMIPS (lpj=48002)
[ 42.069093] pid_max: default: 32768 minimum: 301
[ 42.069222] Security Framework initialized
[ 42.069241] SELinux: Disabled at boot.
[ 42.069286] Mount-cache hash table entries: 512
[ 42.069792] Initializing cgroup subsys cpuacct
[ 42.069843] Initializing cgroup subsys devices
[ 42.069852] Initializing cgroup subsys freezer
[ 42.069860] Initializing cgroup subsys net_cls
[ 42.070062] Performance events: Supported PMU type is 'ultra3i'
[ 42.071682] CPU 0: synchronized TICK with master CPU (last diff 0 cycles, maxerr 6 cycles)
[ 42.071692] Brought up 2 CPUs
[ 42.071722] Testing NMI watchdog ... OK.
[ 42.152193] devtmpfs: initialized
[ 42.152688] print_constraints: dummy:
[ 42.152826] NET: Registered protocol family 16
[ 42.156708] /pci@1c,600000: TOMATILLO PCI Bus Module ver[4:0]
[ 42.156726] /pci@1c,600000: PCI IO[7ce01000000] MEM[7cf00000000]
[ 42.158679] PCI: Scanning PBM /pci@1c,600000
[ 42.158823] pci 0000:00:03.0: PME# supported from D3hot
[ 42.158833] pci 0000:00:03.0: PME# disabled
[ 42.159022] /pci@1d,700000: TOMATILLO PCI Bus Module ver[4:0]
[ 42.159037] /pci@1d,700000: PCI IO[7c601000000] MEM[7c700000000]
[ 42.160969] PCI: Scanning PBM /pci@1d,700000
[ 42.161130] pci 0001:00:04.0: supports D1 D2
[ 42.161180] pci 0001:00:04.1: supports D1 D2
[ 42.161364] /pci@1e,600000: TOMATILLO PCI Bus Module ver[4:0]
[ 42.161385] /pci@1e,600000: PCI IO[7fe01000000] MEM[7ff00000000]
[ 42.163328] PCI: Scanning PBM /pci@1e,600000
[ 42.163514] pci 0002:00:06.0: quirk: [io 0x7fe01000800-0x7fe0100083f] claimed by ali7101 ACPI
[ 42.163544] pci 0002:00:06.0: quirk: [io 0x7fe01000600-0x7fe0100061f] claimed by ali7101 SMB
[ 42.163620] pci 0002:00:08.0: supports D1 D2
[ 42.163627] pci 0002:00:08.0: PME# supported from D2 D3hot D3cold
[ 42.163635] pci 0002:00:08.0: PME# disabled
[ 42.163690] pci 0002:00:0a.0: PME# supported from D3cold
[ 42.163696] pci 0002:00:0a.0: PME# disabled
[ 42.163754] pci 0002:00:0b.0: PME# supported from D3cold
[ 42.163761] pci 0002:00:0b.0: PME# disabled
[ 42.163950] pci 0002:01:08.0: supports D1 D2
[ 42.163956] pci 0002:01:08.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 42.163964] pci 0002:01:08.0: PME# disabled
[ 42.164034] pci 0002:01:08.1: supports D1 D2
[ 42.164040] pci 0002:01:08.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 42.164048] pci 0002:01:08.1: PME# disabled
[ 42.164117] pci 0002:01:08.2: supports D1 D2
[ 42.164123] pci 0002:01:08.2: PME# supported from D0 D1 D2 D3hot
[ 42.164131] pci 0002:01:08.2: PME# disabled
[ 42.164200] pci 0002:01:0b.0: supports D1 D2
[ 42.164206] pci 0002:01:0b.0: PME# supported from D0 D1 D2 D3hot
[ 42.164214] pci 0002:01:0b.0: PME# disabled
[ 42.165051] /pci@1f,700000: TOMATILLO PCI Bus Module ver[4:0]
[ 42.165071] /pci@1f,700000: PCI IO[7f601000000] MEM[7f700000000]
[ 42.167014] PCI: Scanning PBM /pci@1f,700000
[ 42.167178] pci 0003:00:02.0: supports D2
[ 42.169200] bio: create slab <bio-0> at 0
[ 42.169521] vgaarb: loaded
[ 42.170021] /pci@1e,600000/isa@7/rtc@0,70: RTC regs at 0x7fe01000070
[ 42.170519] Switching to clocksource stick
[ 42.171318] Switched to NOHz mode on CPU #0
[ 42.173039] Switched to NOHz mode on CPU #1
[ 42.177422] NET: Registered protocol family 2
[ 42.177624] IP route cache hash table entries: 4096 (order: 2, 32768 bytes)
[ 42.178172] TCP established hash table entries: 16384 (order: 5, 262144 bytes)
[ 42.179001] TCP bind hash table entries: 16384 (order: 5, 262144 bytes)
[ 42.179796] TCP: Hash tables configured (established 16384 bind 16384)
[ 42.179812] TCP reno registered
[ 42.179829] UDP hash table entries: 256 (order: 0, 8192 bytes)
[ 42.179871] UDP-Lite hash table entries: 256 (order: 0, 8192 bytes)
[ 42.180190] NET: Registered protocol family 1
[ 42.180257] pci 0002:00:07.0: Activating ISA DMA hang workarounds
[ 42.180338] PCI: CLS 64 bytes, default 64
[ 42.180450] Unpacking initramfs...
[ 42.760636] Freeing initrd memory: 9823k freed
[ 42.761478] power: Control reg at 7fe01000800
[ 42.761845] chmc: UltraSPARC-IIIi memory controller at /memory-controller@0,0
[ 42.761878] chmc: UltraSPARC-IIIi memory controller at /memory-controller@1,0
[ 42.762217] audit: initializing netlink socket (disabled)
[ 42.762256] type=2000 audit(0.772:1): initialized
[ 42.808149] HugeTLB registered 4 MB page size, pre-allocated 0 pages
[ 42.812594] VFS: Disk quotas dquot_6.5.2
[ 42.812820] Dquot-cache hash table entries: 1024 (order 0, 8192 bytes)
[ 42.813102] msgmni has been set to 1996
[ 42.813683] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 42.813709] io scheduler noop registered
[ 42.813722] io scheduler deadline registered
[ 42.813838] io scheduler cfq registered (default)
[ 42.814374] e3d: Found device at 0003:00:02.0
[ 42.814527] fbcon: e3d (fb0) is primary device
[ 42.875062] Console: switching to colour frame buffer device 160x64
[ 42.933479] f008fc3c: ttyS0 at MMIO 0x7fe010003f8 (irq = 23) is a 16550A
[ 42.934086] f0091678: ttyS1 at MMIO 0x7fe010002e8 (irq = 23) is a 16550A
[ 42.934936] [drm] Initialized drm 1.1.0 20060810
[ 42.935906] Uniform Multi-Platform E-IDE driver
[ 42.936296] ide-gd driver 1.18
[ 42.936749] mousedev: PS/2 mouse device common for all mice
[ 42.937691] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 42.938148] rtc0: no alarms, 114 bytes nvram
[ 42.939179] TCP cubic registered
[ 42.939704] NET: Registered protocol family 10
[ 42.941337] Mobile IPv6
[ 42.941515] NET: Registered protocol family 17
[ 42.941831] Registering the dns_resolver key type
[ 42.942363] registered taskstats version 1
[ 42.943108] rtc_cmos rtc_cmos: setting system clock to 2012-04-06 14:18:59 UTC (1333721939)
[ 42.943687] Initializing network drop monitor service
[ 42.986758] udev[44]: starting version 164
[ 43.148051] SCSI subsystem initialized
[ 43.149483] tg3.c:v3.119 (May 18, 2011)
[ 43.149830] PCI: Enabling device: (0000:00:03.0), cmd 2
[ 43.160764] alim15x3 0002:00:0d.0: IDE controller (0x10b9:0x5229 rev 0xc4)
[ 43.161279] PCI: Enabling device: (0002:00:0d.0), cmd 5
[ 43.161342] alim15x3 0002:00:0d.0: 100% native mode on irq 29
[ 43.161750] ide0: BM-DMA at 0x7fe01000a20-0x7fe01000a27
[ 43.162156] ide1: BM-DMA at 0x7fe01000a28-0x7fe01000a2f
[ 43.162587] Probing IDE interface ide0...
[ 43.198759] PCI: Enabling device: (0002:01:0b.0), cmd 2
[ 43.199053] usbcore: registered new interface driver usbfs
[ 43.199515] usbcore: registered new interface driver hub
[ 43.201129] PCI: Enabling device: (0001:00:04.0), cmd 147
[ 43.201710] sym0: <1010-66> rev 0x1 at pci 0001:00:04.0 irq 12
[ 43.205740] usbcore: registered new device driver usb
[ 43.209185] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 43.219097] sym0: No NVRAM, ID 7, Fast-80, LVD, parity checking
[ 43.260916] sym0: SCSI BUS has been reset.
[ 43.261278] scsi0 : sym-2.2.3
[ 43.261588] firewire_ohci: Added fw-ohci device 0002:01:0b.0, OHCI v1.10, 4 IR + 8 IT contexts, quirks 0x2
[ 43.262933] PCI: Enabling device: (0002:01:08.2), cmd 2
[ 43.262956] ehci_hcd 0002:01:08.2: EHCI Host Controller
[ 43.280120] ehci_hcd 0002:01:08.2: new USB bus registered, assigned bus number 1
[ 43.294547] tg3 0000:00:03.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
[ 43.296958] PCI: Enabling device: (0001:00:04.1), cmd 147
[ 43.297531] sym1: <1010-66> rev 0x1 at pci 0001:00:04.1 irq 13
[ 43.316770] sym1: No NVRAM, ID 7, Fast-80, LVD, parity checking
[ 43.354552] tg3 0000:00:03.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
[ 43.368138] ehci_hcd 0002:01:08.2: irq 32, io mem 0x7ff03004000
[ 43.391707] sym1: SCSI BUS has been reset.
[ 43.408268] scsi1 : sym-2.2.3
[ 43.414549] tg3 0000:00:03.0: vpd r/w failed. This is likely a firmware bug on this device. Contact the card vendor for a firmware update.
[ 43.417568] tg3 0000:00:03.0: eth0: Tigon3 [partno(none) rev 1002] (PCI:66MHz:64-bit) MAC address 00:03:ba:44:d1:39
[ 43.417580] tg3 0000:00:03.0: eth0: attached PHY is 5703 (10/100/1000Base-T Ethernet) (WireSpeed[1], EEE[0])
[ 43.417590] tg3 0000:00:03.0: eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
[ 43.417598] tg3 0000:00:03.0: eth0: dma_rwctrl[763f0000] dma_mask[32-bit]
[ 43.430557] ehci_hcd 0002:01:08.2: USB 2.0 started, EHCI 1.00
[ 43.430629] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 43.430637] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 43.430643] usb usb1: Product: EHCI Host Controller
[ 43.430649] usb usb1: Manufacturer: Linux 3.0.0 ehci_hcd
[ 43.430654] usb usb1: SerialNumber: 0002:01:08.2
[ 43.431154] hub 1-0:1.0: USB hub found
[ 43.431169] hub 1-0:1.0: 5 ports detected
[ 43.433097] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 43.779014] firewire_core: created device fw0: GUID 000516000040a1e6, S400
[ 43.982608] Probing IDE interface ide1...
[ 44.382751] hdc: JLMS XJ-HD166S, ATAPI CD/DVD-ROM drive
[ 44.734714] hdc: host max PIO5 wanted PIO255(auto-tune) selected PIO4
[ 44.734777] hdc: UDMA/33 mode selected
[ 44.752061] ide0 at 0x7fe01000a00-0x7fe01000a07,0x7fe01000a1a on irq 29
[ 44.769955] ide1 at 0x7fe01000a10-0x7fe01000a17,0x7fe01000a0a on irq 29
[ 44.787541] ohci_hcd 0002:00:0a.0: OHCI Host Controller
[ 44.805531] ohci_hcd 0002:00:0a.0: new USB bus registered, assigned bus number 2
[ 44.823384] ohci_hcd 0002:00:0a.0: irq 27, io mem 0x7ff01000000
[ 44.898638] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 44.916188] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 44.933754] usb usb2: Product: OHCI Host Controller
[ 44.951250] usb usb2: Manufacturer: Linux 3.0.0 ohci_hcd
[ 44.968653] usb usb2: SerialNumber: 0002:00:0a.0
[ 44.986414] hub 2-0:1.0: USB hub found
[ 45.003825] hub 2-0:1.0: 2 ports detected
[ 45.023019] PCI: Enabling device: (0002:00:0b.0), cmd 2
[ 45.023042] ohci_hcd 0002:00:0b.0: OHCI Host Controller
[ 45.040565] ohci_hcd 0002:00:0b.0: new USB bus registered, assigned bus number 3
[ 45.041737] libata version 3.00 loaded.
[ 45.058151] ohci_hcd 0002:00:0b.0: irq 28, io mem 0x7ff02000000
[ 45.134599] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 45.152299] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 45.169845] usb usb3: Product: OHCI Host Controller
[ 45.187125] usb usb3: Manufacturer: Linux 3.0.0 ohci_hcd
[ 45.204350] usb usb3: SerialNumber: 0002:00:0b.0
[ 45.222017] hub 3-0:1.0: USB hub found
[ 45.239201] hub 3-0:1.0: 2 ports detected
[ 45.256430] PCI: Enabling device: (0002:01:08.0), cmd 2
[ 45.256446] ohci_hcd 0002:01:08.0: OHCI Host Controller
[ 45.264020] ide-cd driver 5.00
[ 45.264472] ide-cd: hdc: ATAPI 48X DVD-ROM drive, 512kB Cache
[ 45.264483] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 45.324840] ohci_hcd 0002:01:08.0: new USB bus registered, assigned bus number 4
[ 45.342479] ohci_hcd 0002:01:08.0: irq 30, io mem 0x7ff03000000
[ 45.346558] usb 2-1: new full speed USB device number 2 using ohci_hcd
[ 45.464625] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 45.482514] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 45.500347] usb usb4: Product: OHCI Host Controller
[ 45.518195] usb usb4: Manufacturer: Linux 3.0.0 ohci_hcd
[ 45.520463] usb 2-1: New USB device found, idVendor=046d, idProduct=c52f
[ 45.520473] usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 45.520479] usb 2-1: Product: USB Receiver
[ 45.520484] usb 2-1: Manufacturer: Logitech
[ 45.605267] usb usb4: SerialNumber: 0002:01:08.0
[ 45.622871] hub 4-0:1.0: USB hub found
[ 45.640321] hub 4-0:1.0: 3 ports detected
[ 45.657338] usb 2-2: new low speed USB device number 3 using ohci_hcd
[ 45.674283] PCI: Enabling device: (0002:01:08.1), cmd 2
[ 45.674302] ohci_hcd 0002:01:08.1: OHCI Host Controller
[ 45.691365] ohci_hcd 0002:01:08.1: new USB bus registered, assigned bus number 5
[ 45.708156] ohci_hcd 0002:01:08.1: irq 31, io mem 0x7ff03002000
[ 45.808609] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 45.825194] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 45.841692] usb usb5: Product: OHCI Host Controller
[ 45.858132] usb usb5: Manufacturer: Linux 3.0.0 ohci_hcd
[ 45.874479] usb usb5: SerialNumber: 0002:01:08.1
[ 45.891220] hub 5-0:1.0: USB hub found
[ 45.907547] hub 5-0:1.0: 2 ports detected
[ 45.930406] usb 2-2: New USB device found, idVendor=0b38, idProduct=0010
[ 45.947118] usb 2-2: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 45.992085] input: Logitech USB Receiver as /devices/root/f007134c/pci0002:00/0002:00:0a.0/usb2/2-1/2-1:1.0/input/input0
[ 46.010087] generic-usb 0003:046D:C52F.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0002:00:0a.0-1/input0
[ 46.038680] input: Logitech USB Receiver as /devices/root/f007134c/pci0002:00/0002:00:0a.0/usb2/2-1/2-1:1.1/input/input1
[ 46.058246] generic-usb 0003:046D:C52F.0002: input,hiddev0,hidraw1: USB HID v1.11 Device [Logitech USB Receiver] on usb-0002:00:0a.0-1/input1
[ 46.083952] input: HID 0b38:0010 as /devices/root/f007134c/pci0002:00/0002:00:0a.0/usb2/2-2/2-2:1.0/input/input2
[ 46.103364] generic-usb 0003:0B38:0010.0003: input,hidraw2: USB HID v1.10 Keyboard [HID 0b38:0010] on usb-0002:00:0a.0-2/input0
[ 46.134710] input: HID 0b38:0010 as /devices/root/f007134c/pci0002:00/0002:00:0a.0/usb2/2-2/2-2:1.1/input/input3
[ 46.154765] generic-usb 0003:0B38:0010.0004: input,hidraw3: USB HID v1.10 Device [HID 0b38:0010] on usb-0002:00:0a.0-2/input1
[ 46.175270] usbcore: registered new interface driver usbhid
[ 46.195415] usbhid: USB HID core driver
[ 46.339454] scsi 0:0:0:0: Direct-Access ModusLnk MXJ3735SC800600P M108 PQ: 0 ANSI: 3
[ 46.339481] scsi target0:0:0: tagged command queuing enabled, command queue depth 16.
[ 46.339502] scsi target0:0:0: Beginning Domain Validation
[ 46.344030] scsi target0:0:0: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
[ 46.352225] scsi target0:0:0: Ending Domain Validation
[ 46.353493] scsi 0:0:1:0: Direct-Access ModusLnk MXJ3735SC800600P M108 PQ: 0 ANSI: 3
[ 46.353504] scsi target0:0:1: tagged command queuing enabled, command queue depth 16.
[ 46.353519] scsi target0:0:1: Beginning Domain Validation
[ 46.358019] scsi target0:0:1: FAST-80 WIDE SCSI 160.0 MB/s DT (12.5 ns, offset 31)
[ 46.366508] scsi target0:0:1: Ending Domain Validation
[ 50.235497] sd 0:0:1:0: [sdb] 143571316 512-byte logical blocks: (73.5 GB/68.4 GiB)
[ 50.257371] sd 0:0:0:0: [sda] 143571316 512-byte logical blocks: (73.5 GB/68.4 GiB)
[ 50.259530] sd 0:0:1:0: [sdb] Write Protect is off
[ 50.259540] sd 0:0:1:0: [sdb] Mode Sense: b3 00 00 08
[ 50.260839] sd 0:0:1:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 50.272837] sdb: sdb1 sdb3
[ 50.349696] sd 0:0:0:0: [sda] Write Protect is off
[ 50.372214] sd 0:0:0:0: [sda] Mode Sense: b3 00 00 08
[ 50.373476] sd 0:0:1:0: [sdb] Attached SCSI disk
[ 50.395654] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 50.432564] sda: sda1 sda2 sda3 sda4
[ 50.463327] sd 0:0:0:0: [sda] Attached SCSI disk
[ 50.690562] EXT3-fs: barriers not enabled
[ 50.813667] kjournald starting. Commit interval 5 seconds
[ 50.813788] EXT3-fs (sda2): mounted filesystem with ordered data mode
[ 51.861601] udev[334]: starting version 164
[ 52.395991] PCI: Enabling device: (0002:00:08.0), cmd 3
[ 55.954502] AC'97 1 does not respond - RESET
[ 55.990505] AC'97 1 access is not valid [0xffffffff], removing mixer.
[ 56.013704] ali mixer 1 creating error.
[ 56.503799] Adding 2996112k swap on /dev/sda4. Priority:-1 extents:1 across:2996112k
[ 56.796695] EXT3-fs (sda2): using internal journal
[ 56.938409] loop: module loaded
[ 58.307505] EXT3-fs: barriers not enabled
[ 58.337349] kjournald starting. Commit interval 5 seconds
[ 58.357947] EXT3-fs (sdb1): using internal journal
[ 58.377874] EXT3-fs (sdb1): mounted filesystem with ordered data mode
[ 59.164654] tg3 0000:00:03.0: eth0: Failed to load firmware "tigon/tg3_tso.bin"
[ 59.184272] tg3 0000:00:03.0: eth0: TSO capability disabled
[ 60.489830] tg3 0000:00:03.0: eth0: No firmware running
[ 60.545984] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 62.082103] tg3 0000:00:03.0: eth0: Link is up at 100 Mbps, full duplex
[ 62.101803] tg3 0000:00:03.0: eth0: Flow control is on for TX and on for RX
[ 62.121351] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 62.415094] sshd (1128): /proc/1128/oom_adj is deprecated, please use /proc/1128/oom_score_adj instead.
[ 72.618433] eth0: no IPv6 routers present
[ 463.780930] sd 0:0:0:0: [sda] ABORT operation started
[ 463.957621] scsi target0:0:0: control msgout: 80 20 23 d.
[ 463.967404] sd 0:0:0:0: ABORT operation complete.
[ 463.976539] sd 0:0:0:0: [sda] ABORT operation started
[ 463.985664] sd 0:0:0:0: ABORT operation failed.
[ 463.994629] sd 0:0:0:0: [sda] ABORT operation started
[ 464.002878] sd 0:0:0:0: ABORT operation failed.
[ 464.010359] sd 0:0:0:0: [sda] ABORT operation started
[ 464.018031] sd 0:0:0:0: ABORT operation failed.
[ 464.025813] sd 0:0:0:0: [sda] ABORT operation started
[ 464.033793] sd 0:0:0:0: ABORT operation failed.
[ 464.041894] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050182] sd 0:0:0:0: ABORT operation failed.
[ 464.050188] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050194] sd 0:0:0:0: ABORT operation failed.
[ 464.050199] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050204] sd 0:0:0:0: ABORT operation failed.
[ 464.050210] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050215] sd 0:0:0:0: ABORT operation failed.
[ 464.050220] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050225] sd 0:0:0:0: ABORT operation failed.
[ 464.050230] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050235] sd 0:0:0:0: ABORT operation failed.
[ 464.050240] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050245] sd 0:0:0:0: ABORT operation failed.
[ 464.050251] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050256] sd 0:0:0:0: ABORT operation failed.
[ 464.050261] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050266] sd 0:0:0:0: ABORT operation failed.
[ 464.050271] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050276] sd 0:0:0:0: ABORT operation failed.
[ 464.050281] sd 0:0:0:0: [sda] ABORT operation started
[ 464.050286] sd 0:0:0:0: ABORT operation failed.
[ 474.048873] sd 0:0:0:0: [sda] ABORT operation started
[ 474.219132] scsi target0:0:0: control msgout: 80 20 7b d.
[ 474.229785] sd 0:0:0:0: ABORT operation complete.
[ 474.240310] sd 0:0:0:0: [sda] DEVICE RESET operation started
[ 474.251039] sd 0:0:0:0: DEVICE RESET operation complete.
[ 474.479644] scsi target0:0:0: control msgout: c.
[ 474.490834] scsi target0:0:0: has been reset
[ 474.501823] sd 0:0:0:0: [sda] BUS RESET operation started
[ 474.515257] sym0: SCSI BUS reset detected.
[ 474.531042] sym0: SCSI BUS has been reset.
[ 474.542381] sd 0:0:0:0: BUS RESET operation complete.
Reply to: