Bug#617756: linux-image-2.6.32-5-686: NMI received for unknown reason 3d on CPU 0.
Package: linux-2.6
Version: 2.6.32-30
Severity: normal
*** Please type your report below this line ***
Hi,
I don't know whether this is a hardware problem or a kernel problem
but figured I'd report it. I just upgraded to squeeze and am getting
these messages on the console and in dmesg:
[31934.320083] Uhhuh. NMI received for unknown reason 3d on CPU 0.
[31934.320109] Do you have a strange power saving mode enabled?
[31934.320125] Dazed and confused, but trying to continue
[36364.673879] Uhhuh. NMI received for unknown reason 2d on CPU 0.
[36364.673905] Do you have a strange power saving mode enabled?
[36364.673922] Dazed and confused, but trying to continue
I first noticed a problem, related or not, a month or so ago after the
box crashed, twice over the course of a week, while still
running lenny (stock kernel). I've not had a crash before or
since but went looking and found (lenny kernel) messages in
/var/log/kern.log like:
Mar 6 06:41:34 gabby kernel: [2057246.866534] APIC error on CPU0: 04(02)
Mar 6 06:42:14 gabby kernel: [2057286.761093] APIC error on CPU0: 02(02)
Mar 6 06:42:15 gabby kernel: [2057287.933099] APIC error on CPU0: 02(02)
Mar 6 07:15:27 gabby kernel: [2059280.046999] APIC error on CPU0: 02(08)
Mar 6 18:56:26 gabby kernel: [2101339.542267] APIC error on CPU0: 08(02)
Mar 6 20:09:24 gabby kernel: [2105716.940076] APIC error on CPU0: 02(02)
Mar 6 21:51:51 gabby kernel: [2111863.940268] APIC error on CPU0: 02(02)
Mar 6 23:56:45 gabby kernel: [2119358.238512] APIC error on CPU0: 02(04)
Mar 7 00:05:31 gabby kernel: [2119883.748038] APIC error on CPU0: 04(02)
Mar 7 00:08:33 gabby kernel: [2120066.165826] APIC error on CPU0: 02(04)
Mar 7 00:08:39 gabby kernel: [2120071.596018] APIC error on CPU0: 04(04)
Mar 7 00:09:57 gabby kernel: [2120149.586813] APIC error on CPU0: 04(04)
Mar 7 00:10:33 gabby kernel: [2120185.756067] APIC error on CPU0: 04(08)
Mar 7 00:14:01 gabby kernel: [2120393.772139] APIC error on CPU0: 08(02)
Mar 7 00:19:24 gabby kernel: [2120716.844046] APIC error on CPU0: 02(08)
Mar 7 00:23:48 gabby kernel: [2120980.711715] APIC error on CPU0: 08(04)
Mar 7 00:24:01 gabby kernel: [2120993.752039] APIC error on CPU0: 04(02)
Mar 7 00:24:18 gabby kernel: [2121010.620038] APIC error on CPU0: 02(02)
I don't know how long this has been going on.
Right around the time of the crash my asterisk setup stopped giving me
dial tone -- a problem I've ignored since I'm not using it.
I've a card with 4 regular phone jacks in the box.
(And now that I've updated to squeeze asterisk has changed
the name of the zaptel drivers and the configs are frobbed
as a result and I've no time to straighten the problem out.)
I don't know if this is related or not.
FWIW I googled and came up with this url
https://bugzilla.redhat.com/show_bug.cgi?id=676881
claiming that RH has fixed something similar for old 686
chips in 'kernel-2.6.38-0.rc6.git6.1.fc15'.
I'm hoping that by reporting early this might get fixed
in squeeze.
FYI, network addresses and netmask obsfuscated.
Thanks for the help.
-- Package-specific info:
** Version:
Linux version 2.6.32-5-686 (Debian 2.6.32-30) (ben@decadent.org.uk) (gcc version 4.3.5 (Debian 4.3.5-4) ) #1 SMP Wed Jan 12 04:01:41 UTC 2011
** Command line:
BOOT_IMAGE=/vmlinuz-2.6.32-5-686 root=/dev/mapper/vg00-root ro quiet
** Not tainted
** Kernel log:
[ 1.383369] usb usb2: Product: UHCI Host Controller
[ 1.383372] usb usb2: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.383376] usb usb2: SerialNumber: 0000:00:10.0
[ 1.383693] usb usb2: configuration #1 chosen from 1 choice
[ 1.383811] hub 2-0:1.0: USB hub found
[ 1.383832] hub 2-0:1.0: 2 ports detected
[ 1.383921] uhci_hcd 0000:00:10.1: PCI INT B -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.383932] uhci_hcd 0000:00:10.1: UHCI Host Controller
[ 1.383947] uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 3
[ 1.383973] uhci_hcd 0000:00:10.1: irq 21, io base 0x0000d800
[ 1.384075] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.384080] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.384084] usb usb3: Product: UHCI Host Controller
[ 1.384088] usb usb3: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.384091] usb usb3: SerialNumber: 0000:00:10.1
[ 1.384289] usb usb3: configuration #1 chosen from 1 choice
[ 1.384399] hub 3-0:1.0: USB hub found
[ 1.384418] hub 3-0:1.0: 2 ports detected
[ 1.384506] uhci_hcd 0000:00:10.2: PCI INT C -> Link[ALKB] -> GSI 21 (level, low) -> IRQ 21
[ 1.384518] uhci_hcd 0000:00:10.2: UHCI Host Controller
[ 1.384531] uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 4
[ 1.384559] uhci_hcd 0000:00:10.2: irq 21, io base 0x0000dc00
[ 1.384625] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.384630] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.384634] usb usb4: Product: UHCI Host Controller
[ 1.384638] usb usb4: Manufacturer: Linux 2.6.32-5-686 uhci_hcd
[ 1.384641] usb usb4: SerialNumber: 0000:00:10.2
[ 1.384820] usb usb4: configuration #1 chosen from 1 choice
[ 1.384928] hub 4-0:1.0: USB hub found
[ 1.384946] hub 4-0:1.0: 2 ports detected
[ 1.544474] ata1.00: ATA-7: SAMSUNG SP0411N, TW100-13, max UDMA/100
[ 1.544482] ata1.00: 78242976 sectors, multi 16: LBA48
[ 1.552323] ata1.00: configured for UDMA/100
[ 1.552540] scsi 0:0:0:0: Direct-Access ATA SAMSUNG SP0411N TW10 PQ: 0 ANSI: 5
[ 1.716359] ata2.00: ATAPI: LITE-ON CD-ROM LTN-529S, 7S56, max UDMA/33
[ 1.732236] ata2.00: configured for UDMA/33
[ 1.732735] scsi 1:0:0:0: CD-ROM LITE-ON CD-ROM LTN-529S 7S56 PQ: 0 ANSI: 5
[ 1.767960] sd 0:0:0:0: [sda] 78242976 512-byte logical blocks: (40.0 GB/37.3 GiB)
[ 1.768090] sd 0:0:0:0: [sda] Write Protect is off
[ 1.768096] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.768136] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.768387] sda:sr0: scsi3-mmc drive: 52x/52x cd/rw xa/form2 cdda tray
[ 1.771910] Uniform CD-ROM driver Revision: 3.20
[ 1.772595] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 1.773391] sda1 sda2 < sda5 >
[ 1.779402] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.808111] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.808963] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 2.076085] device-mapper: uevent: version 1.0.3
[ 2.077159] device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@redhat.com
[ 2.461882] PM: Starting manual resume from disk
[ 2.461892] PM: Resume from partition 254:1
[ 2.461895] PM: Checking hibernation image.
[ 2.462212] PM: Error -22 checking image file
[ 2.462216] PM: Resume from disk failed.
[ 2.501976] kjournald starting. Commit interval 5 seconds
[ 2.501996] EXT3-fs: mounted filesystem with ordered data mode.
[ 4.098700] udev[302]: starting version 164
[ 4.629324] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input1
[ 4.629340] ACPI: Power Button [PWRB]
[ 4.629445] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input2
[ 4.629458] ACPI: Sleep Button [SLPB]
[ 4.629591] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 4.629597] ACPI: Power Button [PWRF]
[ 4.629785] processor LNXCPU:00: registered as cooling_device1
[ 4.658336] input: PC Speaker as /devices/platform/pcspkr/input/input4
[ 4.659688] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 4.826696] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 4.923932] NET: Registered protocol family 23
[ 4.926074] parport_pc 00:09: reported by Plug and Play ACPI
[ 4.926191] parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE,EPP]
[ 5.666583] Error: Driver 'pcspkr' is already registered, aborting...
[ 5.739550] ACPI: PCI Interrupt Link [ALKC] BIOS reported IRQ 0, using IRQ 22
[ 5.739557] ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
[ 5.739575] VIA 82xx Audio 0000:00:11.5: PCI INT C -> Link[ALKC] -> GSI 22 (level, low) -> IRQ 22
[ 5.739745] VIA 82xx Audio 0000:00:11.5: setting latency timer to 64
[ 7.064735] EXT3 FS on dm-0, internal journal
[ 7.237627] loop: module loaded
[ 7.714911] Adding 1642488k swap on /dev/mapper/vg00-swap_1. Priority:-1 extents:1 across:1642488k
[ 8.019769] kjournald starting. Commit interval 5 seconds
[ 8.019927] EXT3 FS on sda1, internal journal
[ 8.019936] EXT3-fs: mounted filesystem with ordered data mode.
[ 8.631104] eth0: link up, 100Mbps, half-duplex, lpa 0x40A1
[ 18.856014] eth0: no IPv6 routers present
[ 542.745186] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 542.747910] SGI XFS Quota Management subsystem
[ 542.773865] JFS: nTxBlock = 4906, nTxLock = 39252
[ 542.851425] NTFS driver 2.1.29 [Flags: R/W MODULE].
[ 542.937625] QNX4 filesystem 0.2.3 registered.
[ 543.030370] Btrfs loaded
[ 1504.000079] ata1: lost interrupt (Status 0x50)
[ 1504.000132] sd 0:0:0:0: [sda] Unhandled error code
[ 1504.000136] sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_TIMEOUT
[ 1504.000142] sd 0:0:0:0: [sda] CDB: Write(10): 2a 00 00 0e 1e 7e 00 00 08 00
[ 1504.000156] end_request: I/O error, dev sda, sector 925310
[ 1504.000219] Buffer I/O error on device dm-0, logical block 53356
[ 1504.000264] lost page write due to I/O error on dm-0
[31934.320083] Uhhuh. NMI received for unknown reason 3d on CPU 0.
[31934.320109] Do you have a strange power saving mode enabled?
[31934.320125] Dazed and confused, but trying to continue
** Model information
not available
** Loaded modules:
Module Size Used by
btrfs 366823 0
zlib_deflate 15822 1 btrfs
crc32c 2172 1
libcrc32c 762 1 btrfs
ufs 56158 0
qnx4 5118 0
hfsplus 61001 0
hfs 33093 0
minix 17814 0
ntfs 163909 0
vfat 6570 0
msdos 5118 0
fat 34912 2 vfat,msdos
jfs 134664 0
xfs 417005 0
exportfs 2618 1 xfs
reiserfs 176190 0
ext4 257803 0
jbd2 56155 1 ext4
crc16 1027 1 ext4
ext2 46293 0
loop 9765 0
snd_via82xx 15256 0
gameport 6061 1 snd_via82xx
snd_ac97_codec 79148 1 snd_via82xx
ac97_bus 710 1 snd_ac97_codec
snd_mpu401_uart 4067 1 snd_via82xx
snd_pcm 47226 2 snd_via82xx,snd_ac97_codec
snd_rawmidi 12513 1 snd_mpu401_uart
snd_seq_device 3673 1 snd_rawmidi
snd_timer 12258 1 snd_pcm
snd 34375 7 snd_via82xx,snd_ac97_codec,snd_mpu401_uart,snd_pcm,snd_rawmidi,snd_seq_device,snd_timer
soundcore 3450 1 snd
i2c_viapro 4419 0
i2c_core 12696 1 i2c_viapro
snd_page_alloc 5045 2 snd_via82xx,snd_pcm
via_ircc 13311 0
parport_pc 15799 0
irda 75956 1 via_ircc
shpchp 21220 0
evdev 5609 4
parport 22554 1 parport_pc
pcspkr 1207 0
pci_hotplug 18065 1 shpchp
crc_ccitt 1039 1 irda
button 3598 0
processor 26327 0
ext3 94212 2
jbd 32169 1 ext3
mbcache 3762 3 ext4,ext2,ext3
dm_mod 46082 6
sg 15968 0
sr_mod 10770 0
sd_mod 25977 3
crc_t10dif 1012 1 sd_mod
cdrom 26487 1 sr_mod
ata_generic 2067 0
uhci_hcd 16057 0
fan 2586 0
pata_via 5701 3
ehci_hcd 27851 0
thermal 9206 0
libata 115753 2 ata_generic,pata_via
via_rhine 14627 0
thermal_sys 9378 3 processor,fan,thermal
usbcore 98453 3 uhci_hcd,ehci_hcd
mii 2714 1 via_rhine
nls_base 4541 7 hfsplus,hfs,ntfs,vfat,fat,jfs,usbcore
scsi_mod 101429 4 sg,sr_mod,sd_mod,libata
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
allow-hotplug eth0
iface eth0 inet static
address xxx.xxx.xxx.xxx
netmask 255.255.255.0
network xxx.xxx.xxx.xxx
broadcast xxx.xxx.xxx.xxx
gateway xxx.xxx.xxx.xxx
# dns-* options are implemented by the resolvconf package, if installed
dns-nameservers xxx.xxx.xxx.xxx
dns-search meme.com
** Network status:
*** IP interfaces and addresses:
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
inet 127.0.0.1/8 scope host lo
inet6 ::1/128 scope host
valid_lft forever preferred_lft forever
2: eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UNKNOWN qlen 1000
link/ether 00:e0:4c:e0:7a:8c brd ff:ff:ff:ff:ff:ff
inet xxx.xxx.xxx.xxx/yy brd xxx.xxx.xxx.xxx scope global eth0
inet6 fe80::2e0:4cff:fee0:7a8c/64 scope link
valid_lft forever preferred_lft forever
*** Device statistics:
Inter-| Receive | Transmit
face |bytes packets errs drop fifo frame compressed multicast|bytes packets errs drop fifo colls carrier compressed
lo: 8842 74 0 0 0 0 0 0 8842 74 0 0 0 0 0 0
eth0: 9847457 15943 0 0 0 0 0 0 1399666 10114 22 0 0 2645 22 0
*** Protocol statistics:
Ip:
15676 total packets received
0 forwarded
0 incoming packets discarded
15662 incoming packets delivered
9915 requests sent out
28 reassemblies required
14 packets reassembled ok
Icmp:
193 ICMP messages received
0 input ICMP message failed.
ICMP input histogram:
echo requests: 193
195 ICMP messages sent
0 ICMP messages failed
ICMP output histogram:
destination unreachable: 2
echo replies: 193
IcmpMsg:
InType8: 193
OutType0: 193
OutType3: 2
Tcp:
22 active connections openings
5 passive connection openings
4 failed connection attempts
0 connection resets received
1 connections established
15065 segments received
9313 segments send out
0 segments retransmited
0 bad segments received.
26 resets sent
Udp:
402 packets received
2 packets to unknown port received.
0 packet receive errors
407 packets sent
UdpLite:
TcpExt:
2 TCP sockets finished time wait in fast timer
28 delayed acks sent
5 packets directly queued to recvmsg prequeue.
8650 packet headers predicted
149 acknowledgments not containing data payload received
5265 predicted acknowledgments
5 connections reset due to unexpected data
IpExt:
InOctets: 9617411
OutOctets: 1259804
*** Device features:
eth0: 0x0
lo: 0x13865
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8378 [KM400/A] Chipset Host Bridge [1106:3205]
Subsystem: VIA Technologies, Inc. VT8378 [KM400/A] Chipset Host Bridge [1106:3205]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Capabilities: <access denied>
Kernel driver in use: agpgart-via
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237/VX700 PCI Bridge [1106:b198] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: dc000000-ddffffff
Prefetchable memory behind bridge: d8000000-dbffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR+
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:08.0 Communication controller [0780]: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface [e159:0001]
Subsystem: Device [b119:0003]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (250ns min, 32000ns max)
Interrupt: pin A routed to IRQ 11
Region 0: I/O ports at d000 [size=256]
Region 1: Memory at de000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: Biostar Microtech Int'l Corp Device [1565:3204]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 21
Region 4: I/O ports at d400 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: Biostar Microtech Int'l Corp Device [1565:3204]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at d800 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 80) (prog-if 00 [UHCI])
Subsystem: Biostar Microtech Int'l Corp Device [1565:3204]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 21
Region 4: I/O ports at dc00 [size=32]
Capabilities: <access denied>
Kernel driver in use: uhci_hcd
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 82) (prog-if 20 [EHCI])
Subsystem: Biostar Microtech Int'l Corp Device [1565:3204]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin D routed to IRQ 21
Region 0: Memory at de001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177]
Subsystem: VIA Technologies, Inc. VT8235 ISA Bridge [1106:3177]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:11.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Biostar Microtech Int'l Corp Device [1565:3204]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 20
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at e000 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_via
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 50)
Subsystem: Biostar Microtech Int'l Corp Device [1565:8714]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 22
Region 0: I/O ports at e400 [size=256]
Capabilities: <access denied>
Kernel driver in use: VIA 82xx Audio
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 74)
Subsystem: Biostar Microtech Int'l Corp Device [1565:2200]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 23
Region 0: I/O ports at e800 [size=256]
Region 1: Memory at de002000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: via-rhine
01:00.0 VGA compatible controller [0300]: VIA Technologies, Inc. KM400/KN400/P4M800 [S3 UniChrome] [1106:7205] (rev 01) (prog-if 00 [VGA controller])
Subsystem: Biostar Microtech Int'l Corp Device [1565:1200]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (500ns min)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at d8000000 (32-bit, prefetchable) [size=64M]
Region 1: Memory at dc000000 (32-bit, non-prefetchable) [size=16M]
[virtual] Expansion ROM at dd000000 [disabled] [size=64K]
Capabilities: <access denied>
** USB devices:
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 6.0
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.32-5-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.32-5-686 depends on:
ii debconf [debconf-2.0] 1.5.36.1 Debian configuration management sy
ii initramfs-tools [linux-initra 0.98.8 tools for generating an initramfs
ii linux-base 2.6.32-30 Linux image base package
ii module-init-tools 3.12-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.32-5-686 recommends:
ii firmware-linux-free 2.6.32-30 Binary firmware for various driver
ii libc6-i686 2.11.2-10 Embedded GNU C Library: Shared lib
Versions of packages linux-image-2.6.32-5-686 suggests:
ii grub 0.97-64 GRand Unified Bootloader (dummy pa
pn linux-doc-2.6.32 <none> (no description available)
Versions of packages linux-image-2.6.32-5-686 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-2.6.32-5-686/prerm/removing-running-kernel-2.6.32-5-686: true
linux-image-2.6.32-5-686/postinst/depmod-error-initrd-2.6.32-5-686: false
linux-image-2.6.32-5-686/postinst/ignoring-do-bootloader-2.6.32-5-686:
linux-image-2.6.32-5-686/postinst/missing-firmware-2.6.32-5-686:
Reply to: