--- Begin Message ---
- To: Debian Bug Tracking System <submit@bugs.debian.org>
- Subject: linux-image-2.6.26-2-amd64/686: reloads b43-phy0
- From: Andres Cimmarusti <acimmarusti@gmail.com>
- Date: Tue, 21 Jul 2009 10:21:19 -0400
- Message-id: <20090721142119.3314.75949.reportbug@debturion>
Package: linux-image-2.6.26-2-amd64
Version: 2.6.26-17
Severity: normal
This doesn't happen everytime, but it happens often. My wireless device
is based on a broadcom 4318 as can be evidenced below. When I boot, the
firmware is loaded correctly and the LED turns on, but just as I log in
the LED turns off and this causes Network-Manager to fail to
automatically connect to my wireless network. A minute goes by and then
the LED turns back on. This causes me to have to manually connect.
I did the following:
# grep -i b43 /var/log/*
/var/log/syslog:Jul 21 08:40:11 debturion kernel: [ 9.571373]
b43-phy0: Broadcom 4318 WLAN found
/var/log/syslog:Jul 21 08:40:18 debturion kernel: [ 23.580452] input:
b43-phy0 as /class/input/input9
/var/log/syslog:Jul 21 08:40:18 debturion kernel: [ 23.716055]
firmware: requesting b43/ucode5.fw
/var/log/syslog:Jul 21 08:40:18 debturion kernel: [ 23.776608]
firmware: requesting b43/pcm5.fw
/var/log/syslog:Jul 21 08:40:18 debturion kernel: [ 23.848264]
firmware: requesting b43/b0g0initvals5.fw
/var/log/syslog:Jul 21 08:40:19 debturion kernel: [ 23.914947]
firmware: requesting b43/b0g0bsinitvals5.fw
/var/log/syslog:Jul 21 08:40:19 debturion kernel: [ 24.152040]
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
/var/log/syslog:Jul 21 08:40:20 debturion kernel: [ 25.512200]
Registered led device: b43-phy0::radio
/var/log/syslog:Jul 21 08:40:20 debturion NetworkManager: <info> wlan0:
Device is fully-supported using driver 'b43-pci-bridge'.
/var/log/syslog:Jul 21 08:41:22 debturion kernel: [ 86.940911] input:
b43-phy0 as /class/input/input10
/var/log/syslog:Jul 21 08:41:22 debturion kernel: [ 87.144504]
b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
/var/log/syslog:Jul 21 08:41:23 debturion kernel: [ 88.336181]
Registered led device: b43-phy0::radio
It can be seen from this output that b43-phy0 is reloaded automatically
after a minute of being shut off (for reasons that elude me). It is also
assigned to a different input.
This didn't happen to my computer when I was using kernel 2.6.24 (Ubuntu
8.04) or 2.6.27 (Ubuntu 8.10 / OpenSuSe 11.1). This has happened to me
using both 32-bit and 64-bit versions of Lenny and using also 2.6.26-1
version.
-- Package-specific info:
** Version:
Linux version 2.6.26-2-amd64 (Debian 2.6.26-17) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Sun Jun 21 04:47:08 UTC 2009
** Command line:
root=/dev/hda1 ro quiet
** Tainted: P (1)
** Kernel log:
[ 4.747946] PM: Starting manual resume from disk
[ 4.813042] kjournald starting. Commit interval 5 seconds
[ 4.813054] EXT3-fs: mounted filesystem with ordered data mode.
[ 6.576209] udevd version 125 started
[ 7.548881] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 7.563838] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 7.659634] input: Power Button (FF) as /class/input/input2
[ 7.687730] ACPI: Power Button (FF) [PWRF]
[ 7.687815] input: Sleep Button (FF) as /class/input/input3
[ 7.720905] ACPI: Sleep Button (FF) [SLPF]
[ 7.720985] input: Lid Switch as /class/input/input4
[ 7.736175] ACPI: Lid Switch [LID]
[ 7.736249] input: Power Button (CM) as /class/input/input5
[ 7.768076] ACPI: Power Button (CM) [PWRB]
[ 7.871788] ACPI: WMI: Mapper loaded
[ 7.980339] ACPI: AC Adapter [ACAD] (on-line)
[ 8.230314] ACPI: Battery Slot [BAT1] (battery present)
[ 8.290103] input: Video Bus as /class/input/input6
[ 8.316101] ACPI: Video Device [VGA] (multi-head: yes rom: no post: no)
[ 8.371767] piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device
[ 8.918463] ACPI: PCI Interrupt 0000:00:14.6[B] -> GSI 17 (level, low) -> IRQ 17
[ 9.028056] MC'97 0 converters and GPIO not ready (0x1)
[ 9.029251] ACPI: PCI Interrupt 0000:00:14.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 9.037630] Yenta: CardBus bridge found at 0000:06:04.0 [103c:30a4]
[ 9.037658] PCI: Bus 7, cardbus bridge: 0000:06:04.0
[ 9.037660] IO window: 0x0000a400-0x0000a4ff
[ 9.037665] IO window: 0x0000a800-0x0000a8ff
[ 9.037671] PREFETCH window: 0x8c000000-0x8c3fffff
[ 9.037676] MEM window: 0x88000000-0x8bffffff
[ 9.037684] Yenta: Enabling burst memory read transactions
[ 9.037690] Yenta: Using INTVAL to route CSC interrupts to PCI
[ 9.037692] Yenta: Routing CardBus interrupts to ISA
[ 9.037698] Yenta TI: socket 0000:06:04.0, mfunc 0x00a61b22, devctl 0x64
[ 9.233871] input: PC Speaker as /class/input/input7
[ 9.269328] Yenta: ISA IRQ mask 0x0ef8, PCI irq 20
[ 9.269333] Socket status: 30000006
[ 9.269338] pcmcia: parent PCI bridge I/O window: 0xa000 - 0xafff
[ 9.269341] pcmcia: parent PCI bridge Memory window: 0xc0200000 - 0xc02fffff
[ 9.468375] b43-phy0: Broadcom 4318 WLAN found
[ 9.536532] phy0: Selected rate control algorithm 'pid'
[ 9.641823] Broadcom 43xx driver loaded [ Features: PMLR, Firmware-ID: FW13 ]
[ 9.642318] ACPI: PCI Interrupt 0000:06:04.3[B] -> GSI 23 (level, low) -> IRQ 23
[ 9.963110] Synaptics Touchpad, model: 1, fw: 6.2, id: 0x1a0b1, caps: 0xa04713/0x200000
[ 10.025861] input: SynPS/2 Synaptics TouchPad as /class/input/input8
[ 11.575773] Adding 3012148k swap on /dev/hda5. Priority:-1 extents:1 across:3012148k
[ 11.996464] EXT3 FS on hda1, internal journal
[ 12.594580] loop: module loaded
[ 12.814334] fglrx: module license 'Proprietary. (C) 2002 - ATI Technologies, Starnberg, GERMANY' taints kernel.
[ 12.840328] [fglrx] Maximum main memory to use for locked dma buffers: 1886 MBytes.
[ 12.840358] [fglrx] vendor: 1002 device: 5955 count: 1
[ 12.840717] [fglrx] ioport: bar 1, base 0x9000, size: 0x100
[ 12.840742] ACPI: PCI Interrupt 0000:01:05.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 12.841557] [fglrx] Driver built-in PAT support is enabled successfully
[ 12.841602] [fglrx] module loaded - fglrx 8.56.4 [Dec 1 2008] with 1 minors
[ 15.677911] powernow-k8: Found 1 AMD Turion(tm) 64 Mobile Technology ML-40 processors (1 cpu cores) (version 2.20.00)
[ 15.677954] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x4
[ 15.677956] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0x6
[ 15.677958] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0x8
[ 15.677960] powernow-k8: 3 : fid 0x8 (1600 MHz), vid 0xa
[ 15.677962] powernow-k8: 4 : fid 0x0 (800 MHz), vid 0x16
[ 15.677990] powernow-k8: ph2 null fid transition 0xe
[ 17.303684] NET: Registered protocol family 10
[ 17.304211] lo: Disabled Privacy Extensions
[ 17.647533] pnp: the driver 'parport_pc' has been registered
[ 17.648116] lp: driver loaded but no devices found
[ 17.671382] ppdev: user-space parallel port driver
[ 18.792035] Clocksource tsc unstable (delta = -318182810 ns)
[ 22.641386] Bluetooth: Core ver 2.11
[ 22.645178] NET: Registered protocol family 31
[ 22.645183] Bluetooth: HCI device and connection manager initialized
[ 22.645186] Bluetooth: HCI socket layer initialized
[ 22.772244] Bluetooth: L2CAP ver 2.9
[ 22.772248] Bluetooth: L2CAP socket layer initialized
[ 22.840652] Bluetooth: RFCOMM socket layer initialized
[ 22.840665] Bluetooth: RFCOMM TTY layer initialized
[ 22.840667] Bluetooth: RFCOMM ver 1.8
[ 23.098822] input: b43-phy0 as /class/input/input9
[ 23.216066] firmware: requesting b43/ucode5.fw
[ 23.294558] firmware: requesting b43/pcm5.fw
[ 23.345124] firmware: requesting b43/b0g0initvals5.fw
[ 23.376281] firmware: requesting b43/b0g0bsinitvals5.fw
[ 23.532042] b43-phy0: Loading firmware version 410.2160 (2007-05-26 15:32:10)
[ 24.844397] Registered led device: b43-phy0::radio
[ 24.904824] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 24.961342] eth0: link down
[ 24.961988] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 29.152300] [fglrx] Gart USWC size:192 M.
[ 29.152308] [fglrx] Gart cacheable size:60 M.
[ 29.152313] [fglrx] Reserved FB block: Shared offset:0, size:40000
[ 29.152316] [fglrx] Reserved FB block: Unshared offset:7ff5000, size:b000
[ 70.420821] wlan0: Initial auth_alg=0
[ 70.420831] wlan0: authenticate with AP 00:15:2c:48:a5:d0
[ 70.422132] wlan0: RX authentication from 00:15:2c:48:a5:d0 (alg=0 transaction=2 status=0)
[ 70.422138] wlan0: authenticated
[ 70.422141] wlan0: associate with AP 00:15:2c:48:a5:d0
[ 70.424472] wlan0: RX AssocResp from 00:15:2c:48:a5:d0 (capab=0x421 status=0 aid=4)
[ 70.424481] wlan0: associated
[ 70.424493] wlan0: switched to short barker preamble (BSSID=00:15:2c:48:a5:d0)
[ 70.425293] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 85.504029] wlan0: no IPv6 routers present
** Loaded modules:
Module Size Used by
rfkill_input 8576 0
rfcomm 38176 0
l2cap 23936 5 rfcomm
bluetooth 57124 4 rfcomm,l2cap
ppdev 11656 0
parport_pc 31016 0
lp 14724 0
parport 41776 3 ppdev,parport_pc,lp
ipv6 288328 14
powernow_k8 17156 0
cpufreq_stats 9120 0
cpufreq_userspace 8452 0
cpufreq_ondemand 11792 1
cpufreq_powersave 6400 0
freq_table 9344 3 powernow_k8,cpufreq_stats,cpufreq_ondemand
cpufreq_conservative 11784 0
fglrx 2231064 23
sbp2 25356 0
loop 19468 0
joydev 14848 0
arc4 6272 2
ecb 7296 2
crypto_blkcipher 21636 1 ecb
b43 126504 0
rfkill 11168 3 rfkill_input,b43
rng_core 8968 1 b43
mac80211 162736 1 b43
cfg80211 30096 1 mac80211
pcspkr 7040 0
led_class 8968 1 b43
psmouse 42268 0
input_polldev 8720 1 b43
serio_raw 9860 0
tifm_7xx1 10368 0
tifm_core 13640 1 tifm_7xx1
yenta_socket 27916 1
snd_atiixp 21268 3
snd_atiixp_modem 17292 0
snd_ac97_codec 115416 2 snd_atiixp,snd_atiixp_modem
rsrc_nonstatic 14080 1 yenta_socket
ac97_bus 6272 1 snd_ac97_codec
snd_pcm 81672 4 snd_atiixp,snd_atiixp_modem,snd_ac97_codec
snd_seq 54304 0
snd_timer 25744 3 snd_pcm,snd_seq
snd_seq_device 11668 1 snd_seq
k8temp 9216 0
snd 63688 11 snd_atiixp,snd_atiixp_modem,snd_ac97_codec,snd_pcm,snd_seq,snd_timer,snd_seq_device
soundcore 12064 1 snd
snd_page_alloc 13072 3 snd_atiixp,snd_atiixp_modem,snd_pcm
i2c_piix4 13072 0
i2c_core 27936 1 i2c_piix4
video 24084 0
output 7808 1 video
battery 16776 0
ac 9352 0
wmi 11712 0
button 11680 0
shpchp 34208 0
pci_hotplug 32056 1 shpchp
evdev 14208 9
ext3 124944 1
jbd 51240 1 ext3
mbcache 12804 1 ext3
ide_cd_mod 36360 0
cdrom 37928 1 ide_cd_mod
ide_disk 16512 3
atiixp 8324 0 [permanent]
8139cp 23808 0
ide_pci_generic 9220 0 [permanent]
ide_core 128284 4 ide_cd_mod,ide_disk,atiixp,ide_pci_generic
8139too 28288 0
mii 9856 2 8139cp,8139too
sdhci 19460 0
mmc_core 52448 1 sdhci
ohci1394 32692 0
ieee1394 93816 2 sbp2,ohci1394
ssb 43140 1 b43
pcmcia 38680 2 b43,ssb
pcmcia_core 41508 5 b43,yenta_socket,rsrc_nonstatic,ssb,pcmcia
firmware_class 12544 2 b43,pcmcia
ata_generic 10116 0
libata 165600 1 ata_generic
scsi_mod 160760 2 sbp2,libata
dock 14112 1 libata
ehci_hcd 35980 0
ohci_hcd 25092 0
thermal 22816 0
processor 42304 3 powernow_k8,thermal
fan 9352 0
thermal_sys 17728 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc RS480 Host Bridge [1002:5950] (rev 01)
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 64
00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 00009000-00009fff
Memory behind bridge: c0100000-c01fffff
Prefetchable memory behind bridge: 00000000c8000000-00000000cfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel modules: shpchp
00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a37] (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
Kernel modules: shpchp
00:13.0 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4374] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4374]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c0000000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.1 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4375] (prog-if 10 [OHCI])
Subsystem: ATI Technologies Inc IXP SB400 USB Host Controller [1002:4375]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c0001000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ohci_hcd
Kernel modules: ohci-hcd
00:13.2 USB Controller [0c03]: ATI Technologies Inc IXP SB400 USB2 Host Controller [1002:4373] (prog-if 20 [EHCI])
Subsystem: ATI Technologies Inc IXP SB400 USB2 Host Controller [1002:4373]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 19
Region 0: Memory at c0002000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
Kernel modules: ehci-hcd
00:14.0 SMBus [0c05]: ATI Technologies Inc IXP SB400 SMBus Controller [1002:4372] (rev 11)
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Region 0: I/O ports at 8400 [size=16]
Region 1: Memory at c0003000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: piix4_smbus
Kernel modules: i2c-piix4
00:14.1 IDE interface [0101]: ATI Technologies Inc IXP SB400 IDE Controller [1002:4376] (prog-if 8a [Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 8410 [size=16]
Capabilities: <access denied>
Kernel driver in use: ATIIXP_IDE
Kernel modules: ata_generic, ide-pci-generic, atiixp
00:14.3 ISA bridge [0601]: ATI Technologies Inc IXP SB400 PCI-ISA Bridge [1002:4377]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:14.4 PCI bridge [0604]: ATI Technologies Inc IXP SB400 PCI-PCI Bridge [1002:4371] (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Bus: primary=00, secondary=06, subordinate=08, sec-latency=64
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: c0200000-c02fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:14.5 Multimedia audio controller [0401]: ATI Technologies Inc IXP SB400 AC'97 Audio Controller [1002:4370] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at c0003400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ATI IXP AC97 controller
Kernel modules: snd-atiixp
00:14.6 Modem [0703]: ATI Technologies Inc SB400 AC'97 Modem Controller [1002:4378] (rev 02) (prog-if 00 [Generic])
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 17
Region 0: Memory at c0003800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: ATI IXP MC97 controller
Kernel modules: snd-atiixp-modem
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Kernel driver in use: k8temp
Kernel modules: k8temp
01:05.0 VGA compatible controller [0300]: ATI Technologies Inc Radeon XPRESS 200M 5955 (PCIE) [1002:5955] (prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 255 (2000ns min), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at c8000000 (32-bit, prefetchable) [size=128M]
Region 1: I/O ports at 9000 [size=256]
Region 2: Memory at c0100000 (32-bit, non-prefetchable) [size=64K]
[virtual] Expansion ROM at c0120000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: fglrx_pci
Kernel modules: radeonfb, fglrx
06:02.0 Network controller [0280]: Broadcom Corporation BCM4318 [AirForce One 54g] 802.11g Wireless LAN Controller [14e4:4318] (rev 02)
Subsystem: Hewlett-Packard Company Broadcom 802.11b/g WLAN [103c:1355]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64
Interrupt: pin A routed to IRQ 21
Region 0: Memory at c0204000 (32-bit, non-prefetchable) [size=8K]
Kernel driver in use: b43-pci-bridge
Kernel modules: ssb
06:04.0 CardBus bridge [0607]: Texas Instruments PCIxx21/x515 Cardbus Controller [104c:8031]
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 168, Cache Line Size: 128 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c0208000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=06, secondary=07, subordinate=07, sec-latency=176
Memory window 0: 8c000000-8c3ff000 (prefetchable)
Memory window 1: 88000000-8bfff000
I/O window 0: 0000a400-0000a4ff
I/O window 1: 0000a800-0000a8ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt+ PostWrite+
16-bit legacy interface ports at 0001
Kernel driver in use: yenta_cardbus
Kernel modules: yenta_socket
06:04.2 FireWire (IEEE 1394) [0c00]: Texas Instruments OHCI Compliant IEEE 1394 Host Controller [104c:8032] (prog-if 10 [OHCI])
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (500ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin C routed to IRQ 23
Region 0: Memory at c0209000 (32-bit, non-prefetchable) [size=2K]
Region 1: Memory at c0200000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: ohci1394
Kernel modules: ohci1394
06:04.3 Mass storage controller [0180]: Texas Instruments PCIxx21 Integrated FlashMedia Controller [104c:8033]
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 23
Region 0: Memory at c0206000 (32-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: tifm_7xx1
Kernel modules: tifm_7xx1
06:04.4 SD Host controller [0805]: Texas Instruments PCI6411/6421/6611/6621/7411/7421/7611/7621 Secure Digital Controller [104c:8034]
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 64 (1750ns min, 1000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 20
Region 0: Memory at c020a000 (32-bit, non-prefetchable) [size=256]
Region 1: Memory at c0209c00 (32-bit, non-prefetchable) [size=256]
Region 2: Memory at c0209800 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: sdhci
Kernel modules: sdhci
06:06.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ [10ec:8139] (rev 10)
Subsystem: Hewlett-Packard Company Device [103c:30a4]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128 (8000ns min, 16000ns max)
Interrupt: pin A routed to IRQ 22
Region 0: I/O ports at a000 [size=256]
Region 1: Memory at c020a400 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
Kernel driver in use: 8139too
Kernel modules: 8139too, 8139cp
-- System Information:
Debian Release: 5.0.2
APT prefers stable
APT policy: (500, 'stable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.26-2-amd64 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-amd64 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
linux-image-2.6.26-2-amd64 recommends no packages.
Versions of packages linux-image-2.6.26-2-amd64 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-amd64/postinst/bootloader-error-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/lilo-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/depmod-error-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/postinst/old-dir-initrd-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/create-kimage-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/initrd-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-amd64/preinst/abort-install-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/postinst/old-initrd-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/depmod-error-initrd-2.6.26-2-amd64: false
linux-image-2.6.26-2-amd64/postinst/bootloader-test-error-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/overwriting-modules-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-amd64/preinst/failed-to-move-modules-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/prerm/would-invalidate-boot-loader-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/postinst/old-system-map-link-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/abort-overwrite-2.6.26-2-amd64:
linux-image-2.6.26-2-amd64/preinst/bootloader-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/preinst/elilo-initrd-2.6.26-2-amd64: true
linux-image-2.6.26-2-amd64/prerm/removing-running-kernel-2.6.26-2-amd64: true
--- End Message ---