--- Begin Message ---
Package: linux-image-2.6.26-2-openvz-686
Version: 2.6.26-19lenny2
Severity: critical
Justification: causes serious data loss
[hope my translation was good]
sda1 boot scsi (sdb1 if sda fail) is / 1.9Go
md0 [sda3/sdc3] : raid1 linux (mdadm) & lvm /usr, /var 9Go
md1 [sdd1/sde1] : raid1 & lvm /var/www, /vz, ... 250Go
lvm on md1
/var/www 20Go in reality, but :
# df -h | grep www
/dev/mapper/satavol1-lvm--www
1,9G 1,2G 626M 65% /mnt/satavol1/lvm-www
It's critical, there's nothing in syslog to explain, and some directory in /mnt/satavol1/lvm-www
aren't accessible until umount/mount !!
# umount /mnt/satavol1/lvm-www
umount: /dev/mapper/satavol1-lvm--www: not mounted
umount: /dev/mapper/satavol1-lvm--www: not mounted
# mount /mnt/satavol1/lvm-www
# df -h | grep www
/dev/mapper/satavol1-lvm--www
20G 8,7G 12G 44% /mnt/satavol1/lvm-www
since June 2009, df -h report 4 times 1.9G for my lv partition (note that 1.9 is the size of my sda1
partition instead more (40Go for example)
-- Package-specific info:
** Version:
Linux version 2.6.26-2-openvz-686 (Debian 2.6.26-19lenny2) (dannf@debian.org) (gcc version 4.1.3 20080704 (prerelease) (Debian 4.1.2-25)) #1 SMP Wed Nov 4 22:06:32 UTC 2009
** Command line:
root=/dev/sda1 ro quiet vga=773
** Not tainted
** Kernel log:
[ 27.508319] pci_hotplug: PCI Hot Plug PCI Core version: 0.5
[ 27.557229] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
[ 27.753647] Linux agpgart interface v0.103
[ 27.789506] parport_pc: VIA 686A/8231 detected
[ 27.789519] parport_pc: probing current configuration
[ 27.789545] parport_pc: Current parallel port base: 0x0
[ 27.789555] parport_pc: VIA parallel port disabled in BIOS
[ 27.810101] agpgart: Detected VIA Twister-K/KT133x/KM133 chipset
[ 27.816692] agpgart: AGP aperture is 64M @ 0xe0000000
[ 28.821295] input: Power Button (FF) as /class/input/input1
[ 28.855381] ACPI: Power Button (FF) [PWRF]
[ 28.855555] input: Power Button (CM) as /class/input/input2
[ 28.880288] ACPI: Power Button (CM) [PWRB]
[ 28.880470] input: Sleep Button (CM) as /class/input/input3
[ 28.915944] ACPI: Sleep Button (CM) [SLPB]
[ 29.093211] input: PC Speaker as /class/input/input4
[ 29.284272] ACPI: PCI Interrupt 0000:00:07.5[C] -> Link [LNKD] -> GSI 15 (level, low) -> IRQ 15
[ 29.284439] PCI: Setting latency timer of device 0000:00:07.5 to 64
[ 29.889735] input: ImPS/2 Generic Wheel Mouse as /class/input/input5
[ 31.905295] Adding 489972k swap on /dev/sda2. Priority:-1 extents:1 across:489972k
[ 31.929984] Adding 489972k swap on /dev/sdb2. Priority:-2 extents:1 across:489972k
[ 32.089661] EXT3 FS on sda1, internal journal
[ 32.720016] loop: module loaded
[ 32.845080] md: faulty personality registered for level -5
[ 33.036467] md: bind<sdc3>
[ 33.138892] raid1: raid set md1 active with 1 out of 2 mirrors
[ 56.544042] ReiserFS: dm-10: found reiserfs format "3.6" with standard journal
[ 56.544042] ReiserFS: dm-10: using ordered data mode
[ 56.544042] ReiserFS: dm-10: journal params: device dm-10, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.562380] ReiserFS: dm-10: checking transaction log (dm-10)
[ 56.584048] ReiserFS: dm-10: Using r5 hash to sort names
[ 56.584048] kjournald starting. Commit interval 5 seconds
[ 56.685624] EXT3 FS on sdb1, internal journal
[ 56.685637] EXT3-fs: mounted filesystem with ordered data mode.
[ 56.709934] ReiserFS: dm-9: found reiserfs format "3.6" with standard journal
[ 56.709981] ReiserFS: dm-9: using ordered data mode
[ 56.714787] ReiserFS: dm-9: journal params: device dm-9, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.719487] ReiserFS: dm-9: checking transaction log (dm-9)
[ 56.760840] ReiserFS: dm-9: Using r5 hash to sort names
[ 56.808483] ReiserFS: dm-8: found reiserfs format "3.6" with standard journal
[ 56.808483] ReiserFS: dm-8: using ordered data mode
[ 56.818488] ReiserFS: dm-8: journal params: device dm-8, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.823131] ReiserFS: dm-8: checking transaction log (dm-8)
[ 56.853309] ReiserFS: dm-8: Using r5 hash to sort names
[ 56.869739] ReiserFS: dm-6: found reiserfs format "3.6" with standard journal
[ 56.869739] ReiserFS: dm-6: using ordered data mode
[ 56.872028] ReiserFS: dm-6: journal params: device dm-6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 56.885369] ReiserFS: dm-6: checking transaction log (dm-6)
[ 56.952017] ReiserFS: dm-6: Using r5 hash to sort names
[ 56.952017] ReiserFS: dm-7: found reiserfs format "3.6" with standard journal
[ 56.952017] ReiserFS: dm-7: using ordered data mode
[ 56.952017] ReiserFS: dm-7: journal params: device dm-7, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 57.035230] ReiserFS: dm-7: checking transaction log (dm-7)
[ 57.065802] ReiserFS: dm-7: Using r5 hash to sort names
[ 57.088033] ReiserFS: dm-5: found reiserfs format "3.6" with standard journal
[ 57.088033] ReiserFS: dm-5: using ordered data mode
[ 57.088033] ReiserFS: dm-5: journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 57.106075] ReiserFS: dm-5: checking transaction log (dm-5)
[ 57.145513] ReiserFS: dm-5: Using r5 hash to sort names
[ 57.160369] ReiserFS: dm-2: found reiserfs format "3.6" with standard journal
[ 57.160422] ReiserFS: dm-2: using ordered data mode
[ 57.160756] ReiserFS: dm-2: journal params: device dm-2, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 57.165381] ReiserFS: dm-2: checking transaction log (dm-2)
[ 57.165984] ReiserFS: dm-2: Using r5 hash to sort names
[ 58.580292] e100: eth0: e100_watchdog: link up, 100Mbps, full-duplex
[ 62.637352] NET: Registered protocol family 10
[ 68.412701] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 69.777629] tun: Universal TUN/TAP device driver, 1.6
[ 69.777646] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 70.773675] warning: `vzctl' uses 32-bit capabilities (legacy support in use)
[ 70.781236] CT: 101: started
[ 72.906478] CT: 202: started
[ 72.912075] eth0: no IPv6 routers present
[ 75.309838] CT: 203: started
[ 78.187972] CT: 204: started
[ 82.007536] CT: 205: started
[ 83.220100] veth101.0: no IPv6 routers present
[ 86.844284] CT: 206: started
[ 950.506385] RPC: Registered udp transport module.
[ 950.506404] RPC: Registered tcp transport module.
[ 950.628155] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 1014.631993] CT: 202: stopped
[ 1027.207757] CT: 202: started
[ 3646.764834] CT: 202: stopped
[ 3733.954352] ReiserFS: dm-5: found reiserfs format "3.6" with standard journal
[ 3733.954352] ReiserFS: dm-5: using ordered data mode
[ 3733.961435] ReiserFS: dm-5: journal params: device dm-5, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 3733.966057] ReiserFS: dm-5: checking transaction log (dm-5)
[ 3734.044018] ReiserFS: dm-5: Using r5 hash to sort names
[ 3742.742649] ReiserFS: dm-6: found reiserfs format "3.6" with standard journal
[ 3742.742649] ReiserFS: dm-6: using ordered data mode
[ 3742.753589] ReiserFS: dm-6: journal params: device dm-6, size 8192, journal first block 18, max trans len 1024, max batch 900, max commit age 30, max trans age 30
[ 3742.758288] ReiserFS: dm-6: checking transaction log (dm-6)
[ 3742.804022] ReiserFS: dm-6: Using r5 hash to sort names
[ 3762.396698] CT: 202: started
[ 3824.348628] CT: 202: stopped
[ 3870.124075] CT: 202: started
[ 4106.977823] CT: 202: stopped
[ 4107.512128] CT: 202: started
[27764.999886] CT: 202: started
** Loaded modules:
Module Size Used by
nfsd 188752 0
lockd 56456 1 nfsd
nfs_acl 3680 1 nfsd
auth_rpcgss 34752 1 nfsd
sunrpc 166880 6 nfsd,lockd,nfs_acl,auth_rpcgss
exportfs 4832 1 nfsd
vzethdev 9184 0
vznetdev 14564 10
simfs 4756 5
vzrst 116532 0
vzcpt 97892 0
tun 10148 2 vzrst,vzcpt
vzdquota 32796 5 [permanent]
vzmon 23176 11 vzethdev,vznetdev,vzrst,vzcpt
vzdev 3624 4 vzethdev,vznetdev,vzdquota,vzmon
xt_tcpudp 3584 0
xt_length 2528 0
ipt_ttl 2368 0
xt_tcpmss 2752 0
xt_TCPMSS 4448 0
iptable_mangle 4640 0
iptable_filter 4288 0
xt_multiport 3584 0
xt_limit 2948 0
xt_dscp 3136 0
ipt_REJECT 3552 0
ip_tables 11056 2 iptable_mangle,iptable_filter
x_tables 14404 10 xt_tcpudp,xt_length,ipt_ttl,xt_tcpmss,xt_TCPMSS,xt_multiport,xt_limit,xt_dscp,ipt_REJECT,ip_tables
ipv6 242240 73 vzrst,vzcpt,vzmon
reiserfs 191232 5
faulty 4096 0
loop 13548 0
snd_via82xx 21464 0
gameport 11500 1 snd_via82xx
psmouse 33104 0
snd_ac97_codec 89220 1 snd_via82xx
ac97_bus 2496 1 snd_ac97_codec
pcspkr 3200 0
serio_raw 5508 0
snd_pcm 63492 2 snd_via82xx,snd_ac97_codec
snd_timer 18568 1 snd_pcm
snd_page_alloc 8648 2 snd_via82xx,snd_pcm
snd_mpu401_uart 7168 1 snd_via82xx
button 6864 0
snd_rawmidi 19264 1 snd_mpu401_uart
snd_seq_device 7148 1 snd_rawmidi
snd 46436 7 snd_via82xx,snd_ac97_codec,snd_pcm,snd_timer,snd_mpu401_uart,snd_rawmidi,snd_seq_device
soundcore 7136 1 snd
via686a 12748 0
i2c_viapro 7604 0
i2c_core 20596 1 i2c_viapro
via_agp 8512 1
parport_pc 23396 0
parport 31756 1 parport_pc
agpgart 29576 1 via_agp
shpchp 26360 0
pci_hotplug 24260 1 shpchp
evdev 8736 0
ext3 106120 2
jbd 40276 1 ext3
mbcache 7876 1 ext3
dm_mirror 15904 0
dm_log 9220 1 dm_mirror
dm_snapshot 15108 0
dm_mod 47016 20 dm_mirror,dm_log,dm_snapshot
raid1 18688 2
md_mod 67900 4 faulty,raid1
sd_mod 22968 10
ata_generic 5444 0
sata_promise 10596 2
aic7xxx 118808 6
scsi_transport_spi 20608 1 aic7xxx
libata 141376 2 ata_generic,sata_promise
e100 29900 0
mii 5664 1 e100
dock 9072 1 libata
scsi_mod 130444 4 sd_mod,aic7xxx,scsi_transport_spi,libata
uhci_hcd 19504 0
usbcore 119280 2 uhci_hcd
via82cxxx 7716 0 [permanent]
ide_pci_generic 4676 0 [permanent]
ide_core 97000 2 via82cxxx,ide_pci_generic
thermal 15996 0
processor 33568 1 thermal
fan 4964 0
thermal_sys 11624 3 thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133] [1106:0305] (rev 03)
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 8
Region 0: Memory at e0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: agpgart-via
Kernel modules: via-agp
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP] [1106:8305] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e4000000-e5ffffff
Prefetchable memory behind bridge: d0000000-dfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: shpchp
00:07.0 ISA bridge [0601]: VIA Technologies, Inc. VT82C686 [Apollo Super South] [1106:0686] (rev 40)
Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge [1106:0000]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: parport_pc
Kernel modules: parport_pc
00:07.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at c000 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA_IDE
Kernel modules: via82cxxx
00:07.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 16) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at c400 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:07.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 16) (prog-if 00 [UHCI])
Subsystem: First International Computer, Inc. VA-502 Mainboard [0925:1234]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin D routed to IRQ 7
Region 4: I/O ports at c800 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: uhci_hcd
Kernel modules: uhci-hcd
00:07.4 Host bridge [0600]: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] [1106:3057] (rev 40)
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin ? routed to IRQ 3
Capabilities: [68] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel modules: via686a, i2c-viapro
00:07.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT82C686 AC97 Audio Controller [1106:3058] (rev 50)
Subsystem: Micro-Star International Co., Ltd. MS-6330 Onboard Audio [1462:3300]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 15
Region 0: I/O ports at cc00 [size=256]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at d400 [size=4]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: VIA 82xx Audio
Kernel modules: snd-via82xx
00:09.0 SCSI storage controller [0100]: Adaptec AIC-7892A U160/m [9005:0080] (rev 02)
Subsystem: Adaptec 29160N Ultra160 SCSI Controller [9005:62a0]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (10000ns min, 6250ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 11
BIST result: 00
Region 0: I/O ports at d800 [disabled] [size=256]
Region 1: Memory at e7120000 (64-bit, non-prefetchable) [size=4K]
[virtual] Expansion ROM at 50000000 [disabled] [size=128K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: aic7xxx
Kernel modules: aic7xxx
00:0c.0 Mass storage controller [0180]: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) [105a:3375] (rev 02)
Subsystem: Promise Technology, Inc. PDC20375 (SATA150 TX2plus) [105a:3375]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 96 (1000ns min, 4500ns max), Cache Line Size: 576 bytes
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at dc00 [size=64]
Region 1: I/O ports at e000 [size=16]
Region 2: I/O ports at e400 [size=128]
Region 3: Memory at e7122000 (32-bit, non-prefetchable) [size=4K]
Region 4: Memory at e7100000 (32-bit, non-prefetchable) [size=128K]
[virtual] Expansion ROM at 50020000 [disabled] [size=16K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: sata_promise
Kernel modules: sata_promise
00:0e.0 Ethernet controller [0200]: Intel Corporation 82557/8/9/0/1 Ethernet Pro 100 [8086:1229] (rev 08)
Subsystem: Hewlett-Packard Company NetServer 10/100TX [103c:10cb]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (2000ns min, 14000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 15
Region 0: Memory at e7121000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at e800 [size=64]
Region 2: Memory at e7000000 (32-bit, non-prefetchable) [size=1M]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
Kernel driver in use: e100
Kernel modules: e100, eepro100
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV17 [GeForce4 MX 440] [10de:0171] (rev a3) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 7
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at d0000000 (32-bit, prefetchable) [size=128M]
Region 2: Memory at d8000000 (32-bit, prefetchable) [size=512K]
[virtual] Expansion ROM at d8080000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [44] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64- HTrans- 64bit- FW+ AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>
Kernel modules: nvidiafb
-- System Information:
Debian Release: 5.0.3
APT prefers stable
APT policy: (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 2.6.26-2-openvz-686 (SMP w/1 CPU core)
Locale: LANG=fr_FR.UTF-8, LC_CTYPE=fr_FR.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.26-2-openvz-686 depends on:
ii debconf [debconf-2.0] 1.5.24 Debian configuration management sy
ii initramfs-tools [linux-initra 0.92o tools for generating an initramfs
ii module-init-tools 3.4-1 tools for managing Linux kernel mo
ii vzctl 3.0.22-14 server virtualization solution - c
Versions of packages linux-image-2.6.26-2-openvz-686 recommends:
ii libc6-i686 2.7-18 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.26-2-openvz-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.26 <none> (no description available)
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.26-2-openvz-686/preinst/lilo-has-ramdisk:
linux-image-2.6.26-2-openvz-686/preinst/overwriting-modules-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/preinst/abort-overwrite-2.6.26-2-openvz-686:
linux-image-2.6.26-2-openvz-686/preinst/failed-to-move-modules-2.6.26-2-openvz-686:
linux-image-2.6.26-2-openvz-686/preinst/initrd-2.6.26-2-openvz-686:
linux-image-2.6.26-2-openvz-686/prerm/removing-running-kernel-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/postinst/bootloader-test-error-2.6.26-2-openvz-686:
linux-image-2.6.26-2-openvz-686/prerm/would-invalidate-boot-loader-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/postinst/old-system-map-link-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/preinst/elilo-initrd-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/postinst/old-initrd-link-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/postinst/create-kimage-link-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/postinst/depmod-error-2.6.26-2-openvz-686: false
linux-image-2.6.26-2-openvz-686/postinst/old-dir-initrd-link-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/preinst/abort-install-2.6.26-2-openvz-686:
linux-image-2.6.26-2-openvz-686/postinst/kimage-is-a-directory:
linux-image-2.6.26-2-openvz-686/preinst/lilo-initrd-2.6.26-2-openvz-686: true
linux-image-2.6.26-2-openvz-686/postinst/bootloader-error-2.6.26-2-openvz-686:
linux-image-2.6.26-2-openvz-686/postinst/depmod-error-initrd-2.6.26-2-openvz-686: false
linux-image-2.6.26-2-openvz-686/preinst/bootloader-initrd-2.6.26-2-openvz-686: true
--- End Message ---