Hi David,
On Mon, Jan 02, 2006 at 09:19:45PM +0100, David Schmitt wrote:
> Hi Florian!
>
> Can you reproduce the problem with a current kernel (testing: 2.6.12,
> unstable: 2.6.14)?
well, things have changed a little bit, but just a bit...
using either kernel, I now get an error message with rec/sox:
flo@tigerbay:~$ rec alsa14.wav
Send break (control-c) to end recording
sox: Failed reading /dev/dsp: Invalid audio buffer size 0
I then tried 'cat /dev/dsp > rec.file'; the first time with 2.6.14-2-686
the system froze just like before, but then when I tried with 2.6.12 and
later again with 2.6.14 I get the message "cat: /dev/dsp: Input/output
error" on stdout and there are a few lines in /var/log/syslog:
Jan 5 00:40:32 localhost kernel: sound: DMA buffer(2) == NULL
Jan 5 00:40:32 localhost kernel: Device NM256, chn=out
Jan 5 00:40:32 localhost kernel: NM256: Read request too small; 0
Jan 5 00:40:32 localhost kernel: Sound: DMA (input) timed out - IRQ/DRQ
config error?
Jan 5 00:40:37 localhost last message repeated 9 times
(this is the same for /dev/dsp1, but for /dev/dspW, I only get the error
message to stdout, not the log entries...)
I don't know what you make of this, so...
>
> If yes, could you please post the output of the following commands:
>
> lsmod
> lspci
> lspci -n
> dmesg
>
This is a Dell Latitude LS notebook
on 2.6.14
=========
flo@tigerbay:~$ lsmod
Module Size Used by
visor 19084 0
usbserial 31208 1 visor
fan 4580 0
thermal 13352 0
processor 22684 1 thermal
ipv6 267552 12
pcmcia 40732 2
firmware_class 10528 1 pcmcia
ide_cd 43588 0
cdrom 40928 1 ide_cd
nm256_audio 75772 2
sound 80332 3 nm256_audio
soundcore 9792 3 sound
ac97 5152 1 nm256_audio
joydev 9920 0
i2c_piix4 8816 0
uhci_hcd 33296 0
3c59x 41640 0
parport_pc 36868 0
shpchp 99492 0
mii 5568 1 3c59x
parport 37256 1 parport_pc
i2c_core 22128 1 i2c_piix4
usbcore 127680 4 visor,usbserial,uhci_hcd
pci_hotplug 28628 1 shpchp
intel_agp 24188 1
agpgart 35720 1 intel_agp
yenta_socket 28332 2
rsrc_nonstatic 14208 1 yenta_socket
pcmcia_core 43120 3 pcmcia,yenta_socket,rsrc_nonstatic
rtc 12600 1
floppy 62596 0
ext3 144008 1
jbd 56756 1 ext3
mbcache 9316 1 ext3
ide_disk 18784 3
ide_generic 1120 0 [permanent]
generic 4356 0 [permanent]
piix 10436 0 [permanent]
ide_core 130752 5 ide_cd,ide_disk,ide_generic,generic,piix
evdev 9600 1
mousedev 11584 1
psmouse 39684 0
flo@tigerbay:~$ lspci
0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge (rev 03)
0000:00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE (rev 01)
0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB (rev 01)
0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
0000:00:0a.0 CardBus bridge: Texas Instruments PCI1211
0000:00:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
0000:00:10.0 Communication controller: Agere Systems WinModem 56k (rev 01)
0000:01:00.0 VGA compatible controller: Neomagic Corporation NM2200 [MagicGraph 256AV] (rev 20)
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200 [MagicMedia 256AV Audio] (rev 20)
flo@tigerbay:~$ lspci -n
0000:00:00.0 0600: 8086:7190 (rev 03)
0000:00:01.0 0604: 8086:7191 (rev 03)
0000:00:07.0 0680: 8086:7110 (rev 02)
0000:00:07.1 0101: 8086:7111 (rev 01)
0000:00:07.2 0c03: 8086:7112 (rev 01)
0000:00:07.3 0680: 8086:7113 (rev 03)
0000:00:0a.0 0607: 104c:ac1e
0000:00:0d.0 0200: 10b7:9200 (rev 78)
0000:00:10.0 0780: 11c1:0448 (rev 01)
0000:01:00.0 0300: 10c8:0005 (rev 20)
0000:01:00.1 0401: 10c8:8005 (rev 20)
flo@tigerbay:~$ dmesg
Linux version 2.6.14-2-686 (Debian 2.6.14-7) (maks@sternwelten.at) (gcc version 4.0.3 20051201 (prerelease) (Debian 4.0.2-5)) #1 Wed Dec 28 18:21:03 UTC 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000eb000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fffeb000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32752
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28656 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f70f0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x07ffcc17
ACPI: FADT (v001 DELL Atlas 0x06040000 PTL 0x000f4240) @ 0x07fffb65
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x07fffbd9
ACPI: DSDT (v001 PTL BX-TJ 0x06040000 MSFT 0x01000007) @ 0x00000000
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 10000000 (gap: 08000000:f7feb000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro vga=1 acpi=force resume=/dev/hda5
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01101000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 497.873 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x50
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 125236k/131008k available (1876k kernel code, 5180k reserved, 535k data, 180k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 996.25 BogoMIPS (lpj=498126)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
mtrr: v2.0 (20020519)
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0408)
checking if image is initramfs... it is
softlockup thread 0 started up.
Freeing initrd memory: 1064k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfd9d5, last bus=1
PCI: Using configuration type 1
ACPI: Subsystem revision 20050902
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI quirk: region 8000-803f claimed by PIIX4 ACPI
PCI quirk: region 2180-219f claimed by PIIX4 SMB
PIIX4 devres I PIO at 0398-0399
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: Device [FDDA] status [00000008]: functional but not present; setting present
ACPI: Embedded Controller [EC0] (gpe 0)
ACPI: Device [CDRM] status [00000008]: functional but not present; setting present
ACPI: Power Resource [PFN0] (on)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:05: ioport range 0x8000-0x803f could not be reserved
pnp: 00:05: ioport range 0x2180-0x218f has been reserved
pnp: 00:05: ioport range 0x398-0x399 has been reserved
PCI: Ignore bogus resource 6 [0:0] of 0000:01:00.0
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: fe400000-febfffff
PREFETCH window: f6000000-f7bfffff
PCI: Bus 2, cardbus bridge: 0000:00:0a.0
IO window: 00001000-000010ff
IO window: 00001400-000014ff
PREFETCH window: 10000000-11ffffff
MEM window: 12000000-13ffffff
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Simple Boot Flag at 0x63 set to 0x1
audit: initializing netlink socket (disabled)
audit(1136393752.194:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
TCP established hash table entries: 8192 (order: 3, 32768 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 8
NET: Registered protocol family 20
Using IPI Shortcut mode
ACPI wakeup devices:
PCI0 COMA CRD0 MDEM LID
ACPI: (supports S0 S3 S4 S5)
Freeing unused kernel memory: 180k freed
input: AT Translated Set 2 keyboard on isa0060/serio0
mice: PS/2 mouse device common for all mice
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HTS548040M9AT00, ATA DISK drive
Synaptics Touchpad, model: 1, fw: 4.1, id: 0x8848a1, caps: 0x0/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
hda: hda1 hda2 < hda5 >
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Real Time Clock Driver v1.12
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:00:0a.0 [1028:1225]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x01201212, devctl 0x64
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
input: PC Speaker
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Yenta: ISA IRQ mask 0x08b8, PCI irq 10
Socket status: 30000006
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0d.0: 3Com PCI 3c905C Tornado at 0xfc00. Vers LK1.1.19
USB Universal Host Controller Interface driver v2.3
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:07.2: UHCI Host Controller
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000fce0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: over-current change on port 2
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
NeoMagic 256AV/256ZX audio driver, version 1.1p
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:00.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
NM256: Found card signature in video RAM: 0x27ec00
NM256: Mapping port 1 from 0x266c00 - 0x27ec00
Initialized NeoMagic 256AV audio in PCI native mode
Initialized AC97 mixer
Adding 987956k swap on /dev/hda5. Priority:-1 extents:1 across:987956k
EXT3 FS on hda1, internal journal
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
pcmcia: Detected deprecated PCMCIA ioctl usage.
pcmcia: This interface will soon be removed from the kernel; please expect breakage unless you upgrade to new tools.
pcmcia: see http://www.kernel.org/pub/linux/utils/kernel/pcmcia/pcmcia.html for details.
cs: IO port probe 0x100-0x4ff: excluding 0x170-0x177 0x370-0x37f
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0328b40(lo)
IPv6 over IPv4 tunneling driver
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (59 C)
ACPI: Fan [FAN0] (on)
ACPI: Fan [FAN1] (off)
eth0: no IPv6 routers present
usb 1-1: new full speed USB device using uhci_hcd and address 2
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0
visor 1-1:1.0: Handspring Visor / Palm OS converter detected
usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB0
usb 1-1: Handspring Visor / Palm OS converter now attached to ttyUSB1
usbcore: registered new driver visor
drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver v2.1
usb 1-1: USB disconnect, address 2
visor ttyUSB0: Handspring Visor / Palm OS converter now disconnected from ttyUSB0
visor ttyUSB1: Handspring Visor / Palm OS converter now disconnected from ttyUSB1
visor 1-1:1.0: device disconnected
...
on 2.6.12
=========
flo@tigerbay:~$ lsmod
Module Size Used by
fan 4516 0
thermal 13224 0
processor 21876 1 thermal
ipv6 261984 12
pcmcia 27112 2
af_packet 22216 2
ide_cd 43140 0
cdrom 40640 1 ide_cd
joydev 10144 0
nm256_audio 75708 2
sound 80396 3 nm256_audio
soundcore 9696 3 sound
evdev 9728 1
ac97 5088 1 nm256_audio
mousedev 11776 1
uhci_hcd 32176 0
i2c_piix4 8656 0
shpchp 99428 0
3c59x 41064 0
usbcore 122300 2 uhci_hcd
yenta_socket 23528 1
rsrc_nonstatic 13728 1 yenta_socket
pcmcia_core 51924 3 pcmcia,yenta_socket,rsrc_nonstatic
pci_hotplug 28468 1 shpchp
mii 5696 1 3c59x
i2c_core 21776 1 i2c_piix4
rtc 12376 1
psmouse 31236 0
intel_agp 24092 1
serio_raw 7108 0
parport_pc 36708 0
parport 36936 1 parport_pc
agpgart 35560 1 intel_agp
floppy 60180 0
ext3 141736 1
jbd 56760 1 ext3
mbcache 9252 1 ext3
ide_disk 18688 3
ide_generic 1152 0 [permanent]
via82cxxx 13820 0 [permanent]
trm290 4196 0 [permanent]
triflex 3680 0 [permanent]
slc90e66 5664 0 [permanent]
sis5513 16488 0 [permanent]
siimage 12448 0 [permanent]
serverworks 9032 0 [permanent]
sc1200 7296 0 [permanent]
rz1000 2400 0 [permanent]
piix 10340 0 [permanent]
pdc202xx_old 11168 0 [permanent]
opti621 4324 0 [permanent]
ns87415 4264 0 [permanent]
hpt366 20384 0 [permanent]
hpt34x 5152 0 [permanent]
generic 3808 0 [permanent]
cy82c693 4676 0 [permanent]
cs5530 5312 0 [permanent]
cs5520 4544 0 [permanent]
cmd64x 12028 0 [permanent]
atiixp 5904 0 [permanent]
amd74xx 14396 0 [permanent]
alim15x3 12268 0 [permanent]
aec62xx 7360 0 [permanent]
pdc202xx_new 9248 0 [permanent]
ide_core 130388 28
ide_cd,ide_disk,ide_generic,via82cxxx,trm290,triflex,slc90e66,sis5513,siimage,serverworks,sc1200,rz1000,piix,pdc202xx_old,opti621,ns87415,hpt366,hpt34x,generic,cy82c693,cs5530,cs5520,cmd64x,atiixp,amd74xx,alim15x3,aec62xx,pdc202xx_new
unix 27888 166
fbcon 39936 0
tileblit 2240 1 fbcon
font 8096 1 fbcon
bitblit 5920 1 fbcon
vesafb 7992 0
cfbcopyarea 3872 1 vesafb
cfbimgblt 2816 1 vesafb
cfbfillrect 4128 1 vesafb
softcursor 2176 1 vesafb
capability 4584 0
commoncap 6912 1 capability
flo@tigerbay:~$ lspci
0000:00:00.0 Host bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX
Host bridge (rev 03)
0000:00:01.0 PCI bridge: Intel Corporation 440BX/ZX/DX - 82443BX/ZX/DX
AGP bridge (rev 03)
0000:00:07.0 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ISA (rev 02)
0000:00:07.1 IDE interface: Intel Corporation 82371AB/EB/MB PIIX4 IDE
(rev 01)
0000:00:07.2 USB Controller: Intel Corporation 82371AB/EB/MB PIIX4 USB
(rev 01)
0000:00:07.3 Bridge: Intel Corporation 82371AB/EB/MB PIIX4 ACPI (rev 03)
0000:00:0a.0 CardBus bridge: Texas Instruments PCI1211
0000:00:0d.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M
[Tornado] (rev 78)
0000:00:10.0 Communication controller: Agere Systems WinModem 56k (rev
01)
0000:01:00.0 VGA compatible controller: Neomagic Corporation NM2200
[MagicGraph 256AV] (rev 20)
0000:01:00.1 Multimedia audio controller: Neomagic Corporation NM2200
[MagicMedia 256AV Audio] (rev 20)
flo@tigerbay:~$ lspci -n
0000:00:00.0 0600: 8086:7190 (rev 03)
0000:00:01.0 0604: 8086:7191 (rev 03)
0000:00:07.0 0680: 8086:7110 (rev 02)
0000:00:07.1 0101: 8086:7111 (rev 01)
0000:00:07.2 0c03: 8086:7112 (rev 01)
0000:00:07.3 0680: 8086:7113 (rev 03)
0000:00:0a.0 0607: 104c:ac1e
0000:00:0d.0 0200: 10b7:9200 (rev 78)
0000:00:10.0 0780: 11c1:0448 (rev 01)
0000:01:00.0 0300: 10c8:0005 (rev 20)
0000:01:00.1 0401: 10c8:8005 (rev 20)
flo@tigerbay:~$ dmesg
Linux version 2.6.12-1-686 (horms@tabatha.lab.ultramonkey.org) (gcc version 4.0.2 20050917 (prerelease) (Debian 4.0.1-8)) #1 Tue Sep 27 12:52:50 JST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000eb000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 0000000007ff0000 (usable)
BIOS-e820: 0000000007ff0000 - 0000000007fffc00 (ACPI data)
BIOS-e820: 0000000007fffc00 - 0000000008000000 (ACPI NVS)
BIOS-e820: 00000000fffeb000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
127MB LOWMEM available.
On node 0 totalpages: 32752
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 28656 pages, LIFO batch:15
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 PTLTD ) @ 0x000f70f0
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @ 0x07ffcc17
ACPI: FADT (v001 DELL Atlas 0x06040000 PTL 0x000f4240) @ 0x07fffb65
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @ 0x07fffbd9
ACPI: DSDT (v001 PTL BX-TJ 0x06040000 MSFT 0x01000007) @ 0x00000000
ACPI: BIOS age (2000) fails cutoff (2001), acpi=force is required to enable ACPI
ACPI: acpi=force override
ACPI: PM-Timer IO Port: 0x8008
Allocating PCI resources starting at 08000000 (gap: 08000000:f7feb000)
Built 1 zonelists
Kernel command line: root=/dev/hda1 ro vga=1 acpi=force resume=/dev/hda5
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffd000 (01101000)
Initializing CPU#0
PID hash table entries: 512 (order: 9, 8192 bytes)
Detected 497.960 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x50
Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)
Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)
Memory: 124896k/131008k available (1701k kernel code, 5552k reserved, 712k data, 180k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 987.13 BogoMIPS (lpj=493568)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After vendor identify, caps: 0387f9ff 00000000 00000000 00000000 00000000 00000000 00000000
CPU: L1 I cache: 16K, L1 D cache: 16K
CPU: L2 cache: 256K
CPU serial number disabled.
CPU: After all inits, caps: 0383f9ff 00000000 00000000 00000040 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: Intel Pentium III (Coppermine) stepping 06
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: setting ELCR to 0200 (from 0408)
checking if image is initramfs...it isn't (bad gzip magic numbers); looks like an initrd
Freeing initrd memory: 1488k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xfd9d5, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs *3 4 5 6 7 9 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 9 *10 11 14 15)
ACPI: Device [FDDA] status [00000008]: functional but not present; setting present
ACPI: Embedded Controller [EC0] (gpe 0)
ACPI: Device [CDRM] status [00000008]: functional but not present; setting present
ACPI: Power Resource [PFN0] (off)
ACPI: Power Resource [PFN1] (off)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 11 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:05: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:05: ioport range 0x8000-0x803f could not be reserved
pnp: 00:05: ioport range 0x2180-0x218f has been reserved
pnp: 00:05: ioport range 0x398-0x399 has been reserved
Simple Boot Flag at 0x63 set to 0x1
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Limiting direct PCI/PCI transfers.
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:MOU2] at 0x60,0x64 irq 1,12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP established hash table entries: 8192 (order: 4, 65536 bytes)
TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
TCP: Hash tables configured (established 8192 bind 8192)
ACPI wakeup devices:
PCI0 COMA CRD0 MDEM LID
ACPI: (supports S0 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 1488KiB [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
input: AT Translated Set 2 keyboard on isa0060/serio0
Freeing unused kernel memory: 180k freed
Capability LSM initialized
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller at PCI slot 0000:00:07.1
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfcd0-0xfcd7, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xfcd8-0xfcdf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: HTS548040M9AT00, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
Probing IDE interface ide1...
Probing IDE interface ide2...
Probing IDE interface ide3...
Probing IDE interface ide4...
Probing IDE interface ide5...
hda: max request size: 1024KiB
hda: 78140160 sectors (40007 MB) w/7877KiB Cache, CHS=16383/255/63, UDMA(33)
hda: cache flushes supported
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: hda1: orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 1818798
ext3_orphan_cleanup: deleting unreferenced inode 1818745
ext3_orphan_cleanup: deleting unreferenced inode 3014748
EXT3-fs: hda1: 3 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Floppy drive(s): fd0 is 1.44M
FDC 0 is a National Semiconductor PC87306
Linux agpgart interface v0.101 (c) Dave Jones
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, using FIFO [PCSPP,TRISTATE,COMPAT,ECP]
agpgart: Detected an Intel 440BX Chipset.
agpgart: AGP aperture is 64M @ 0xf8000000
Real Time Clock Driver v1.12
input: PC Speaker
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
Linux Kernel Card Services
options: [pci] [cardbus] [pm]
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 10
PCI: setting IRQ 10 as level-triggered
ACPI: PCI Interrupt 0000:00:0a.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Yenta: CardBus bridge found at 0000:00:0a.0 [1028:1225]
Yenta: Enabling burst memory read transactions
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:00:0a.0, mfunc 0x01201212, devctl 0x64
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Yenta: ISA IRQ mask 0x0838, PCI irq 10
Socket status: 30000006
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:00:0d.0: 3Com PCI 3c905C Tornado at 0xfc00. Vers LK1.1.19
Synaptics Touchpad, model: 1, fw: 4.1, id: 0x8848a1, caps: 0x0/0x0
input: SynPS/2 Synaptics TouchPad on isa0060/serio1
shpchp: shpc_init : shpc_cap_offset == 0
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
piix4_smbus 0000:00:07.3: Found 0000:00:07.3 device
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 10
ACPI: PCI Interrupt 0000:00:07.2[D] -> Link [LNKD] -> GSI 10 (level, low) -> IRQ 10
uhci_hcd 0000:00:07.2: Intel Corporation 82371AB/EB/MB PIIX4 USB
uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:07.2: irq 10, io base 0x0000fce0
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
hub 1-0:1.0: over-current change on port 2
mice: PS/2 mouse device common for all mice
NeoMagic 256AV/256ZX audio driver, version 1.1p
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt 0000:01:00.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
NM256: Found card signature in video RAM: 0x27ec00
NM256: Mapping port 1 from 0x266c00 - 0x27ec00
Initialized NeoMagic 256AV audio in PCI native mode
Initialized AC97 mixer
Adding 987956k swap on /dev/hda5. Priority:-1 extents:1
EXT3 FS on hda1, internal journal
ACPI: PCI Interrupt 0000:00:0d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
NET: Registered protocol family 17
cs: IO port probe 0x100-0x4ff: excluding 0x170-0x177 0x370-0x37f
cs: IO port probe 0x800-0x8ff: clean.
cs: IO port probe 0xc00-0xcff: clean.
cs: IO port probe 0xa00-0xaff: clean.
NET: Registered protocol family 10
Disabled Privacy Extensions on device c0331860(lo)
IPv6 over IPv4 tunneling driver
ACPI: CPU0 (power states: C1[C1] C2[C2])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THRM] (59 C)
ACPI: Fan [FAN0] (off)
ACPI: Fan [FAN1] (off)
eth0: no IPv6 routers present
sound: DMA buffer(2) == NULL
Device NM256, chn=out
NM256: Read request too small; 0
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
Sound: DMA (input) timed out - IRQ/DRQ config error?
...
Attachment:
signature.asc
Description: Digital signature