Heya; I have a problem with one of my machines trying to get GNU/Hurd running. After I unpack the tarball and everything, and boot into the system it's extremely slow. There will be periods where I have to wait 3-5 minutes for my typing to show up at the shell prompt, and if it does show up right away it will only last for about 2 letters before it starts lagging again. I've tried (patiently) running ./native-install, and it takes about 45 minutes for it to reach the stage where I enter timezone configuration. I moved the drive with it on to an older machine and it worked beautifully though (took about 30 seconds to get to the timezone config). My machine is a PII400 with 256 meg of RAM. In the box I have a soundcard, agp video card and a tulip chip NIC. Two harddrives a cdrom and a cdr. Everything works fine in GNU/Linux. I've been told it might be useful to include boot logs for each (Linux and the Hurd), so I've attached those. Any ideas? Thanks; -- Ryan Golbeck <rmgolbeck@uwaterloo.ca> Computer Science University Of Waterloo GPG: 1024D/78916B84 1B1B 2A87 3F00 A7FB 40F3 526D 36CF BA44 7891 6B84
GNUmach 1.2 AT386 boot: physical memory from 0x0 to 0x10000000 GNUmach 1.2 AT386 boot: physical memory from 0x0 to 0x10000000 pcibios_init : BIOS32 Service Directory structure at 0x000faff0 pcibios_init : BIOS32 Service Directory entry at 0xfb470 pcibios_init : PCI BIOS revision 2.10 entry at 0xfb4a0 Probing PCI hardware. hd0: FUJITSU MPD3084AT, 8063MB w/512kB Cache, CHS=1027/255/63 hd1: ST36531A, 6204MB w/128kB Cache, CHS=790/255/63 hd2: YAMAHA CRW8824E, ATAPI CDROM drive hd3: ATAPI 40X CDROM DRIVE, ATAPI CDROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Failed initialization of WD-7000 SCSI card! EATA0: address 0x1f0 in use, skipping probe. EATA0: address 0x170 in use, skipping probe. ppa: Version 1.42 ppa: Probing port 03bc ppa: Probing port 0378 ppa: SPP port present ppa: PS/2 bidirectional port present ppa: Probing port 0278 scsi : 0 hosts. scsi : detected total. tulip.c:v0.91g-ppc 7/16/99 becker@cesdis.gsfc.nasa.gov eth0: Macronix 98715 PMAC rev 32 at 0xec00, 00:20:78:E0:52:F6, IRQ 9. eth0: EEPROM default media type MII 100baseT4. 3c59x.c:v0.99L 5/28/99 Donald Becker http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html 0 3c515 cards found. eth1: D-Link DE-600 pocket adapter: not at I/O 0x378. D-Link DE-620 pocket adapter not identified in the printer port Partition check (DOS partitions): hd0: hd0s1 hd0s2 hd1: hd1s1 hd1s2 hd1s3 com0: at atbus0, port = 3f8, spl = 6, pic = 4. (DOS COM1)
Linux version 2.4.4 (root@tesla) (gcc version 2.95.4 20010319 (Debian prerelease)) #7 Sat Jun 2 14:44:56 EDT 2001 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009fc00 (usable) BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 0000000010000000 (usable) BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved) On node 0 totalpages: 65536 zone(0): 4096 pages. zone(1): 61440 pages. zone(2): 0 pages. Kernel command line: root=/dev/hdb3 hdd=ide-scsi mem=262144K ide_setup: hdd=ide-scsi Initializing CPU#0 Detected 400.935 MHz processor. Console: colour VGA+ 80x25 Calibrating delay loop... 799.53 BogoMIPS Memory: 254968k/262144k available (1426k kernel code, 6788k reserved, 560k data, 196k init, 0k highmem) Dentry-cache hash table entries: 32768 (order: 6, 262144 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 16384 (order: 5, 131072 bytes) CPU: Before vendor init, caps: 0183f9ff 00000000 00000000, vendor = 0 CPU: L1 I cache: 16K, L1 D cache: 16K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU: After vendor init, caps: 0183f9ff 00000000 00000000 00000000 CPU: After generic, caps: 0183f9ff 00000000 00000000 00000000 CPU: Common caps: 0183f9ff 00000000 00000000 00000000 CPU: Intel Pentium II (Deschutes) stepping 02 Enabling fast FPU save and restore... done. Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX PCI: PCI BIOS revision 2.10 entry at 0xfb4a0, last bus=1 PCI: Using configuration type 1 PCI: Probing PCI hardware PCI: Disabled enhanced CPU to PCI posting #2 PCI: Using IRQ router VIA [1106/0596] at 00:07.0 Activating ISA DMA hang workarounds. Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Starting kswapd v1.8 parport0: PC-style at 0x378 [PCSPP(,...)] pty: 256 Unix98 ptys configured lp0: using parport0 (polling). block: queued sectors max/low 169416kB/56472kB, 512 slots per queue Uniform Multi-Platform E-IDE driver Revision: 6.31 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx VP_IDE: IDE controller on PCI bus 00 dev 39 VP_IDE: chipset revision 6 VP_IDE: not 100% native mode: will probe irqs later hda: FUJITSU MPD3084AT, ATA DISK drive hdb: ST36531A, ATA DISK drive hdc: YAMAHA CRW8824E, ATAPI CD/DVD-ROM drive hdd: ATAPI 40X CDROM DRIVE, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: 16514064 sectors (8455 MB) w/512KiB Cache, CHS=1027/255/63 hdb: 12706470 sectors (6506 MB) w/128KiB Cache, CHS=790/255/63 hdc: ATAPI 16X CD-ROM CD-R/RW drive, 4096kB Cache Uniform CD-ROM driver Revision: 3.12 Partition check: hda: hda1 hda2 hdb: hdb1 hdb2 hdb3 Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256). CSLIP: code copyright 1989 Regents of the University of California. loop: loaded (max 8 devices) Serial driver version 5.05a (2001-03-20) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled ttyS00 at 0x03f8 (irq = 4) is a 16550A Real Time Clock Driver v1.10d Linux Tulip driver version 0.9.14e (April 20, 2001) PCI: Found IRQ 9 for device 00:0b.0 eth0: Macronix 98715 PMAC rev 32 at 0xec00, 00:20:78:E0:52:F6, IRQ 9. Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 204M agpgart: Detected Via Apollo Pro chipset agpgart: AGP aperture is 64M @ 0xe0000000 [drm] AGP 0.99 on VIA Apollo Pro @ 0xe0000000 64MB [drm] Initialized mga 2.0.1 20000928 on minor 63 SCSI subsystem driver Revision: 1.00 scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: ATAPI40X Model: CDROM DRIVE Rev: 3.4A Type: CD-ROM ANSI SCSI revision: 02 Detected scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 4x/40x cd/rw xa/form2 cdda tray es1370: version v0.37 time 14:49:47 Jun 2 2001 PCI: Found IRQ 5 for device 00:0a.0 es1370: found adapter at io 0xe800 irq 5 es1370: features: joystick off, line in, mic impedance 0 Linux PCMCIA Card Services 3.1.22 options: [pci] [cardbus] usb.c: registered new driver usbdevfs usb.c: registered new driver hub uhci.c: USB UHCI at I/O 0xe400, IRQ 10 usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 2 ports detected mice: PS/2 mouse device common for all mice NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 16384) NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. ds: no socket drivers loaded! fatfs: bogus cluster size fatfs: bogus cluster size fatfs: bogus cluster size UMSDOS: msdos_read_super failed, mount aborted. reiserfs: checking transaction log (device 03:43) ... Using r5 hash to sort names ReiserFS version 3.6.25 VFS: Mounted root (reiserfs filesystem) readonly. Freeing unused kernel memory: 196k freed Adding Swap: 265064k swap-space (priority -1) ttyS1: LSR safety check engaged! ttyS1: LSR safety check engaged! reiserfs: checking transaction log (device 03:02) ... Using r5 hash to sort names ReiserFS version 3.6.25 EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
Attachment:
pgprbk9bdopOj.pgp
Description: PGP signature