Bug#233312: marked as done (Usually it locks up while "retrieving" a file)
Your message dated Sat, 5 Feb 2011 11:37:37 +0000
with message-id <201102051137.37858.elmig@debianpt.org>
and subject line
has caused the Debian Bug report #233312,
regarding Usually it locks up while "retrieving" a file
to be marked as done.
This means that you claim that the problem has been dealt with.
If this is not the case it is now your responsibility to reopen the
Bug report if necessary, and/or fix the problem forthwith.
(NB: If you are a system administrator and have no idea what this
message is talking about, this may indicate a serious mail system
misconfiguration somewhere. Please contact owner@bugs.debian.org
immediately.)
--
233312: http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=233312
Debian Bug Tracking System
Contact owner@bugs.debian.org with problems
--- Begin Message ---
Package: installation-reports
Debian-installer-version: Daily Build 20040216
Date: 2004-02-17
Method: Booted directly from CD-R via Ontrack DDO
Installation Parameters: None
Machine: Compaq Presario 9548
Processor: Intel Pentium 200 MHz
Memory: 128 MB + 8 MB EDO on system board
Root Device:
-Maxtor DiamondMax 4320 Ultra ATA 8.4 GB (model: 90845D4)
-Software Installed: Maxtor Dynamic Drive Overlay (DDO): Ontrack v9.84
NIC: Linksys Network Everywhere Fast Ethernet Adapter (model: NC100
v2.1)
Graphics:
-onboard: S3 Trio64V+ (1 MB EDO DRAM) [currently disabled in BIOS]
-PCI Slot: Diamond Stealth II S220 (4 MB)
Optical Drive: Factory Installed Internal 4x CD-ROM
Partition Table:
hda1 50 MB ext3 /boot
hda5 3700 MB ext3 /
hda6 512 MB swap
hda7 3750 MB ext3 /home
Base System Installation Checklist:
Initial boot worked: [O]
Configure network HW: [O]
Config network: [O]
Detect CD: [O]
Load installer modules: [O]
Detect hard drives: [O]
Partition hard drives: [O]
Create file systems: [O]
Mount partitions: [O]
Install base system: [E]
Install boot loader: [ ]
Reboot: [ ]
[O] = OK, [E] = Error (please elaborate below), [ ] = didn't try it
Comments/Problems:
I have started the Sarge net-install program over five times. The
installer runs perfectly until it reaches "Installing The Debian Base
System" at which point it freezes. Usually it locks up while
"retrieving" a file (e.g. addusr, bash, base-config, debconf) but will
occasionally lock up during a "validating" operation as well. There
doesn't seem to be a specific file that causes problems because it stops
at a different point each time I run the program. (Usually it stops at
around 10% completion of the base install.) Unfortunately I have not
been able to get past this point in the installer nor have I found a key
combination that will make the software respond after it locks up. It
would be nice if there were an option in the program to re-try or cancel
the operation at hand so that one would not be forced to do a hard
reboot in the event the program freezes. Other than that that I found
the program easy to navigate and quite responsive.
-Jonathon
--- End Message ---
--- Begin Message ---
I am closing this installation report as the Sarge installer is no longer
developed. A lot as changed in the installer and the current debian-installer
release it's now Debian Squeeze.
I invite you to try Debian Squeeze and address any issues against current
release.
--
Melhores cumprimentos/Best regards,
Miguel Figueiredo
http://www.DebianPT.org
--- End Message ---
Reply to: