Bug#302121: Debian Installer
Hi
I've encoutered the same problem trying to install debian on i945 chipset (Asus P5LD2 mainboard).
I've had no disks found using standard installation disks and after replacing the kernel with 2.6.15.4 I get the same error.
I've replaced the kernel on netboot server and on CD and the result is always the same:
VFS: Mounted root (ext2 filesystem).
VFS: Cannot open root device "rd/0" or unknown-block(0,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on
unknown-block(0,0)
I've installed mandriva based on 2.6.12-12mdk-i586-up-1GB kernel and it works OK. Don't know what options and drivers where used to build that kernel.
I've attached results of running lspci and dmesg on mandriva.
Shouldn't initrd.gz be also updated when replacing the kernel?
Best Regards
Pawel Kryczkowski
----------------------------------------------------
5 nominacji do Oscara, 3 Złote Globy: Joaquin Phoenix
i Reese Witherspoon w filmie "Spacer po linie"
- w kinach od 17 lutego.
http://klik.wp.pl/?adr=http%3A%2F%2Fadv.reklama.wp.pl%2Fas%2Fspacerpolinie.html&sid=656
00:00.0 Class 0600: 8086:2770 (rev 02)
00:00.0 Host bridge: Intel Corporation 945G/P Memory Controller Hub (rev 02)
00:1b.0 Class 0403: 8086:27d8 (rev 01)
00:1b.0 Class 0403: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 01)
00:1c.0 Class 0604: 8086:27d0 (rev 01)
00:1c.0 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 1 (rev 01)
00:1c.3 Class 0604: 8086:27d6 (rev 01)
00:1c.3 PCI bridge: Intel Corporation 82801G (ICH7 Family) PCI Express Port 4 (rev 01)
00:1d.0 Class 0c03: 8086:27c8 (rev 01)
00:1d.0 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #1 (rev 01)
00:1d.1 Class 0c03: 8086:27c9 (rev 01)
00:1d.1 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #2 (rev 01)
00:1d.2 Class 0c03: 8086:27ca (rev 01)
00:1d.2 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #3 (rev 01)
00:1d.3 Class 0c03: 8086:27cb (rev 01)
00:1d.3 USB Controller: Intel Corporation 82801G (ICH7 Family) USB UHCI #4 (rev 01)
00:1d.7 Class 0c03: 8086:27cc (rev 01)
00:1d.7 USB Controller: Intel Corporation 82801G (ICH7 Family) USB2 EHCI Controller (rev 01)
00:1e.0 Class 0604: 8086:244e (rev e1)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev e1)
00:1f.0 Class 0601: 8086:27b8 (rev 01)
00:1f.0 ISA bridge: Intel Corporation 82801GB/GR (ICH7 Family) LPC Interface Bridge (rev 01)
00:1f.1 Class 0101: 8086:27df (rev 01)
00:1f.1 IDE interface: Intel Corporation 82801G (ICH7 Family) IDE Controller (rev 01)
00:1f.2 Class 0101: 8086:27c0 (rev 01)
00:1f.2 IDE interface: Intel Corporation 82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controllers cc=IDE (rev 01)
00:1f.3 Class 0c05: 8086:27da (rev 01)
00:1f.3 SMBus: Intel Corporation 82801G (ICH7 Family) SMBus Controller (rev 01)
01:01.0 Class 0300: 102b:0520 (rev 01)
01:01.0 VGA compatible controller: Matrox Graphics, Inc. MGA G200 (rev 01)
01:02.0 Class 0200: 10b7:9200 (rev 74)
01:02.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 74)
01:03.0 Class 0180: 1283:8211 (rev 11)
01:03.0 Mass storage controller: Integrated Technology Express, Inc. ITE 8211F Single Channel UDMA 133 (ASUS 8211 (ITE IT8212 ATA RAID Controller)) (rev 11)
02:00.0 Class 0200: 11ab:4362 (rev 19)
02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8053 Gigabit Ethernet Controller (rev 19)
Linux version 2.6.12-12mdk-i586-up-1GB (apatard@n1.mandriva.com) (gcc version 4.0.1 (4.0.1-5mdk for Mandriva Linux release 2006.0)) #1 Fri Sep 9 17:51:55 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000003ffa0000 (usable)
BIOS-e820: 000000003ffa0000 - 000000003ffae000 (ACPI data)
BIOS-e820: 000000003ffae000 - 000000003ffe0000 (ACPI NVS)
BIOS-e820: 000000003ffe0000 - 0000000040000000 (reserved)
BIOS-e820: 00000000ffb80000 - 0000000100000000 (reserved)
Warning only 896MB will be used.
Use a HIGHMEM enabled kernel.
896MB LOWMEM available.
found SMP MP-table at 000ff780
On node 0 totalpages: 229376
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 225280 pages, LIFO batch:31
HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ACPIAM ) @ 0x000facb0
ACPI: RSDT (v001 A M I OEMRSDT 0x11000501 MSFT 0x00000097) @ 0x3ffa0000
ACPI: FADT (v001 A M I OEMFACP 0x11000501 MSFT 0x00000097) @ 0x3ffa0200
ACPI: MADT (v001 A M I OEMAPIC 0x11000501 MSFT 0x00000097) @ 0x3ffa0390
ACPI: OEMB (v001 A M I AMI_OEM 0x11000501 MSFT 0x00000097) @ 0x3ffae040
>>> ERROR: Invalid checksum
ACPI: MCFG (v001 A M I OEMMCFG 0x11000501 MSFT 0x00000097) @ 0x3ffa8630
ACPI: DSDT (v001 A0227 A0227000 0x00000000 INTL 0x02002026) @ 0x00000000
ACPI: PM-Timer IO Port: 0x808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 20
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x81] disabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 40000000 (gap: 40000000:bfb80000)
Built 1 zonelists
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Initializing CPU#0
Kernel command line: auto BOOT_IMAGE=linux root=801 resume=/dev/sda5
PID hash table entries: 4096 (order: 12, 65536 bytes)
Detected 2542.885 MHz processor.
Using pmtmr for high-res timesource
Console: colour VGA+ 80x25
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Memory: 905348k/917504k available (2116k kernel code, 11700k reserved, 717k data, 244k init, 0k highmem, 0k BadRAM)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 5029.88 BogoMIPS (lpj=2514944)
Mount-cache hash table entries: 512
CPU: After generic identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000000
CPU: After vendor identify, caps: bfebfbff 20000000 00000000 00000000 0000651d 00000000 00000000
monitor/mwait feature present.
using mwait in idle threads.
CPU: Trace cache: 12K uops, L1 D cache: 16K
CPU: L2 cache: 256K
CPU: After all inits, caps: bfebfbff 20000000 00000000 00000080 0000651d 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (24) available
CPU0: Thermal monitoring enabled
CPU: Intel(R) Celeron(R) CPU 2.53GHz stepping 01
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: Looking for DSDT in initrd... not found.
ENABLING IO-APIC IRQs
..TIMER: vector=0x31 pin1=2 pin2=-1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 202k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=3
PCI: Using MMCONFIG
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20050309
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
Boot video device is 0000:01:01.0
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 *5 6 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 *5 6 7 10 11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 15 devices
PnPBIOS: Disabled
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
pnp: 00:07: ioport range 0x290-0x297 has been reserved
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
audit(1139751008.503:0): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
PCI: Setting latency timer of device 0000:00:1c.0 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie02]
Allocate Port Service[pcie03]
ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1c.3 to 64
assign_interrupt_mode Found MSI capability
Allocate Port Service[pcie00]
Allocate Port Service[pcie03]
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12
PNP: PS/2 controller doesn't have AUX irq; using default 0xc
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 112
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
Serial: 8250/16550 driver $Revision: 1.90 $ 8 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 32000K size 1024 blocksize
pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH7: IDE controller at PCI slot 0000:00:1f.1
ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
ICH7: chipset revision 1
ICH7: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio
Probing IDE interface ide0...
hda: LITE-ON DVDRW LDW-451S, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
mice: PS/2 mouse device common for all mice
md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
NET: Registered protocol family 1
ACPI wakeup devices:
P0P1 P0P3 P0P4 P0P5 P0P6 P0P7 P0P8 P0P9 PS2K UAR1 USB2 USB3 USB4 MC97 EUSB USB1
ACPI: (supports S0 S1 S3 S4 S5)
BIOS EDD facility v0.16 2004-Jun-25, 1 devices found
devfs_mk_dev: could not append to parent for md/0
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
SCSI subsystem initialized
libata version 1.11 loaded.
ata_piix version 1.03
ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xA800 ctl 0xA402 bmdma 0x9400 irq 23
ata2: SATA max UDMA/133 cmd 0xA000 ctl 0x9802 bmdma 0x9408 irq 23
input: AT Translated Set 2 keyboard on isa0060/serio0
ata1: dev 0 cfg 49:2f00 82:74eb 83:7f63 84:4003 85:74e9 86:3c43 87:4003 88:207f
ata1: dev 0 ATA, max UDMA/133, 72303840 sectors: lba48
ata1: dev 0 configured for UDMA/133
scsi0 : ata_piix
ATA: abnormal status 0x7F on port 0xA007
ata2: disabling port
scsi1 : ata_piix
Vendor: ATA Model: WDC WD360GD-00FL Rev: 33.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 72303840 512-byte hdwr sectors (37020 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host0/bus0/target0/lun0: p1 p2 < p5 p6 p7 >
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 244k freed
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:1d.0: irq 20, io base 0x00008000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.1: irq 17, io base 0x00008400
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00008800
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1d.3 to 64
uhci_hcd 0000:00:1d.3: UHCI Host Controller
uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.3: irq 19, io base 0x00009000
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
usb 2-1: new low speed USB device using uhci_hcd and address 2
ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:1d.7: irq 20, io mem 0xddfff800
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
usb 2-1: USB disconnect, address 2
usb 2-1: new low speed USB device using uhci_hcd and address 3
usbcore: registered new driver hiddev
input: USB HID v1.10 Mouse [Logitech USB Receiver] on usb-0000:00:1d.1-1
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.01:USB HID core driver
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
ts: Compaq touchscreen protocol output
EXT3 FS on sda1, internal journal
IT8212: IDE controller at PCI slot 0000:01:03.0
ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 20 (level, low) -> IRQ 20
IT8212: chipset revision 17
it821x: controller in pass through mode.
IT8212: 100% native mode on irq 20
ide2: BM-DMA at 0xb400-0xb407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xb408-0xb40f, BIOS settings: hdg:pio, hdh:pio
Probing IDE interface ide2...
Probing IDE interface ide3...
Adding 1124508k swap on /dev/sda5. Priority:-1 extents:1
hw_random hardware driver 1.0.0 loaded
Linux agpgart interface v0.101 (c) Dave Jones
agpgart: Detected an Intel 945G Chipset.
agpgart: AGP aperture is 256M @ 0x0
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda7, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
loop: loaded (max 8 devices)
hda: ATAPI 40X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
NET: Registered protocol family 17
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 19
sk98lin: Network Device Driver v8.23.1.3
(C)Copyright 1999-2005 Marvell(R).
ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:02:00.0 to 64
eth0: Marvell Yukon 88E8053 Gigabit Ethernet Controller
PrefPort:A RlmtMode:Check Link State
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 22 (level, low) -> IRQ 22
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
0000:01:02.0: 3Com PCI 3c905C Tornado at 0xb000. Vers LK1.1.19
ACPI: PCI Interrupt 0000:01:02.0[A] -> GSI 22 (level, low) -> IRQ 22
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (7168 buckets, 57344 max) - 260 bytes per conntrack
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>. http://snowman.net/projects/ipt_recent/
netfilter PSD loaded - (c) astaro AG
IFWLOG: register target
ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:1b.0 to 64
[drm] Initialized drm 1.0.0 20040925
Reply to: