3ware 9550 SATA RAID controller problems
Hi Again,
After finally getting Sarge installed on my SuperMicro X6DHT-G
motherboard system, I am having a problem recognizing the 3ware 9550
SATA Raid Controller card. I have loaded the 3w-9xxx module but that is
not getting me anywhere yet. This system boots from a separate SATA disk
so the system is running, just without the 1.6TB raid array :(
lspci is reporting:
0000:03:02.0 RAID bus controller: 3ware Inc: Unknown device 1003
So, I think what needs to happen next is one or more of the following:
1) upgrade to the 2.6.12 kernel
2) compile the updated vendor source for 3w-9xxx module on either
2.6.8-11 or 2.6.12
3) something simpler that I am missing.
Ideally, I would like to use a stock kernel which was why I was thinking
of getting 2.6.12 from etch otherwise I will need to try and figure out
how to use the kernel-package system and long term maintenance becomes a
bigger problem.
Thoughts and suggestions would be greatly appreciated.
Best regards,
-Steve
I've included the system details below.
Linux carto 2.6.8-11-em64t-p4-smp #1 SMP Mon Oct 3 00:07:51 CEST 2005
x86_64 GNU/Linux
woodbri@carto:~$ lsmod
Module Size Used by
ipv6 280552 16
3w_9xxx 36100 0
ext3 121616 5
jbd 64176 1 ext3
mbcache 11400 1 ext3
tsdev 9472 0
mousedev 12628 0
evdev 11648 0
psmouse 20108 0
genrtc 11516 0
sd_mod 22400 7
usb_storage 69184 0
e1000 83588 0
ide_cd 42784 0
cdrom 39848 1 ide_cd
ide_disk 21504 0
ide_generic 2816 0
generic 6528 0
ide_core 154688 5
usb_storage,ide_cd,ide_disk,ide_generic,generic
floppy 65104 0
fbcon 32164 70
vga16fb 14464 1
vgastate 10240 1 vga16fb
usbserial 33008 0
usbkbd 8960 0
ehci_hcd 32132 0
uhci_hcd 33056 0
thermal 15116 0
processor 15224 1 thermal
fan 5512 0
ata_piix 9988 6
libata 42888 1 ata_piix
scsi_mod 131072 4 3w_9xxx,sd_mod,usb_storage,libata
unix 32032 12
font 10112 1 fbcon
vesafb 7984 0
cfbcopyarea 5120 2 vga16fb,vesafb
cfbimgblt 4352 2 vga16fb,vesafb
cfbfillrect 5248 2 vga16fb,vesafb
woodbri@carto:~$ lspci
0000:00:00.0 Host bridge: Intel Corp. Server Memory Controller Hub (rev 0c)
0000:00:00.1 ff00: Intel Corp. Memory Controller Hub Error Reporting
Register (rev 0c)
0000:00:01.0 System peripheral: Intel Corp. Memory Controller Hub DMA
Controller (rev 0c)
0000:00:02.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port A0 (rev 0c)
0000:00:04.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port B0 (rev 0c)
0000:00:06.0 PCI bridge: Intel Corp. Memory Controller Hub PCI Express
Port C0 (rev 0c)
0000:00:1c.0 PCI bridge: Intel Corp. 6300ESB 64-bit PCI-X Bridge (rev 02)
0000:00:1d.0 USB Controller: Intel Corp. 6300ESB USB Universal Host
Controller (rev 02)
0000:00:1d.1 USB Controller: Intel Corp. 6300ESB USB Universal Host
Controller (rev 02)
0000:00:1d.4 System peripheral: Intel Corp. 6300ESB Watchdog Timer (rev 02)
0000:00:1d.5 PIC: Intel Corp. 6300ESB I/O Advanced Programmable
Interrupt Controller (rev 02)
0000:00:1d.7 USB Controller: Intel Corp. 6300ESB USB2 Enhanced Host
Controller (rev 02)
0000:00:1e.0 PCI bridge: Intel Corp. 82801 PCI Bridge (rev 0a)
0000:00:1f.0 ISA bridge: Intel Corp. 6300ESB LPC Interface Controller
(rev 02)
0000:00:1f.2 IDE interface: Intel Corp. 6300ESB SATA Storage Controller
(rev 02)
0000:00:1f.3 SMBus: Intel Corp. 6300ESB SMBus Controller (rev 02)
0000:01:00.0 PCI bridge: Intel Corp. PCI Bridge Hub A (rev 09)
0000:01:00.1 PIC: Intel Corp. PCI Bridge Hub I/OxAPIC Interrupt
Controller A (rev 09)
0000:01:00.2 PCI bridge: Intel Corp. PCI Bridge Hub B (rev 09)
0000:01:00.3 PIC: Intel Corp. PCI Bridge Hub I/OxAPIC Interrupt
Controller B (rev 09)
0000:03:02.0 RAID bus controller: 3ware Inc: Unknown device 1003
0000:06:01.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit
Ethernet Controller (rev 05)
0000:06:02.0 Ethernet controller: Intel Corp. 82541GI/PI Gigabit
Ethernet Controller (rev 05)
0000:07:01.0 VGA compatible controller: ATI Technologies Inc Rage XL
(rev 27)
woodbri@carto:~$ dmesg
Bootdata ok (command line is root=/dev/sda1 ro console=tty0 )
Linux version 2.6.8-11-em64t-p4-smp (root@athlon) (gcc version 3.4.4
20050314 (prerelease) (Debian 3.4.3-13)) #1 SMP Mon Oct 3 00:07:51 CEST 2005
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009b000 (usable)
BIOS-e820: 000000000009b000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000007ff70000 (usable)
BIOS-e820: 000000007ff70000 - 000000007ff78000 (ACPI data)
BIOS-e820: 000000007ff78000 - 000000007ff80000 (ACPI NVS)
BIOS-e820: 000000007ff80000 - 0000000080000000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec10000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff800000 - 00000000ffc00000 (reserved)
BIOS-e820: 00000000fffffc00 - 0000000100000000 (reserved)
No mptable found.
On node 0 totalpages: 524144
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 520048 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
ACPI: RSDP (v000 PTLTD ) @
0x00000000000f5d60
ACPI: RSDT (v001 PTLTD RSDT 0x06040000 LTP 0x00000000) @
0x000000007ff72fc7
ACPI: FADT (v001 INTEL LINDHRST 0x06040000 PTL 0x00000003) @
0x000000007ff77e2c
ACPI: MADT (v001 PTLTD APIC 0x06040000 LTP 0x00000000) @
0x000000007ff77ea0
ACPI: BOOT (v001 PTLTD $SBFTBL$ 0x06040000 LTP 0x00000001) @
0x000000007ff77f48
ACPI: SPCR (v001 PTLTD $UCRTBL$ 0x06040000 PTL 0x00000001) @
0x000000007ff77f70
ACPI: MCFG (v001 PTLTD MCFG 0x06040000 LTP 0x00000000) @
0x000000007ff77fc0
ACPI: SSDT (v001 PmRef CpuPm 0x00003000 INTL 0x20030224) @
0x000000007ff73003
ACPI: DSDT (v001 Intel LINDHRST 0x06040000 MSFT 0x0100000e) @
0x0000000000000000
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:4 APIC version 16
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x06] enabled)
Processor #6 15:4 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 15:4 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x07] enabled)
Processor #7 15:4 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x03] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
ACPI: IOAPIC (id[0x03] address[0xfec10000] gsi_base[24])
IOAPIC[1]: Assigned apic_id 3
IOAPIC[1]: apic_id 3, version 32, address 0xfec10000, GSI 24-47
ACPI: IOAPIC (id[0x04] address[0xfec80000] gsi_base[48])
IOAPIC[2]: Assigned apic_id 4
IOAPIC[2]: apic_id 4, version 32, address 0xfec80000, GSI 48-71
ACPI: IOAPIC (id[0x05] address[0xfec80400] gsi_base[72])
IOAPIC[3]: Assigned apic_id 5
IOAPIC[3]: apic_id 5, version 32, address 0xfec80400, GSI 72-95
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Using ACPI (MADT) for SMP configuration information
Built 1 zonelists
Kernel command line: root=/dev/sda1 ro console=tty0
Initializing CPU#0
PID hash table entries: 16 (order 4: 256 bytes)
time.c: Using 1.193182 MHz PIT timer.
time.c: Detected 3000.222 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Memory: 2053248k/2096576k available (1606k kernel code, 42524k reserved,
912k data, 152k init)
Calibrating delay loop... 5931.00 BogoMIPS
Security Scaffold v1.0.0 initialized
Capability LSM initialized
Mount-cache hash table entries: 256 (order: 0, 4096 bytes)
CPU: Trace cache: 12K uops
using mwait in idle threads.
CPU: Physical Processor ID: 0
Using IO APIC NMI watchdog
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 0
CPU0: Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
per-CPU timeslice cutoff: 0.00 usecs.
task migration cache decay timeout: 1 msecs.
Booting processor 1/6 rip 6000 rsp 10003267f58
Initializing CPU#1
Calibrating delay loop... 5996.54 BogoMIPS
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 3
Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Booting processor 2/1 rip 6000 rsp 1007fa9ff58
Initializing CPU#2
Calibrating delay loop... 5996.54 BogoMIPS
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 0
Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Booting processor 3/7 rip 6000 rsp 1007fa17f58
Initializing CPU#3
Calibrating delay loop... 5996.54 BogoMIPS
CPU: Trace cache: 12K uops
CPU: Physical Processor ID: 3
Intel(R) Xeon(TM) CPU 3.00GHz stepping 03
Total of 4 processors activated (23920.64 BogoMIPS).
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
2-23, 3-0, 3-1, 3-2, 3-3, 3-4, 3-5, 3-6, 3-7, 3-8, 3-9, 3-10, 3-11,
3-12, 3-13, 3-14, 3-15, 3-16, 3-17, 3-18, 3-19, 3-20, 3-21, 3-22, 3-23,
4-0, 4-1, 4-2, 4-3, 4-4, 4-5, 4-6, 4-7, 4-8, 4-9, 4-10, 4-11, 4-12,
4-13, 4-14, 4-15, 4-16, 4-17, 4-18, 4-19, 4-20, 4-21, 4-22, 4-23, 5-0,
5-1, 5-2, 5-3, 5-4, 5-5, 5-6, 5-7, 5-8, 5-9, 5-10, 5-11, 5-12, 5-13,
5-14, 5-15, 5-16, 5-17, 5-18, 5-19, 5-20, 5-21, 5-22, 5-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=-1
activating NMI Watchdog ... done.
testing NMI watchdog ... OK.
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
checking TSC synchronization across 4 CPUs: passed.
time.c: Using PIT/TSC based timekeeping.
Brought up 4 CPUs
CPU0: online
domain 0: span 05
groups: 01 04
domain 1: span 0f
groups: 05 0a
CPU1: online
domain 0: span 0a
groups: 02 08
domain 1: span 0f
groups: 0a 05
CPU2: online
domain 0: span 05
groups: 04 01
domain 1: span 0f
groups: 05 0a
CPU3: online
domain 0: span 0a
groups: 08 02
domain 1: span 0f
groups: 0a 05
checking if image is initramfs...it isn't (ungzip failed); looks like an
initrd
NET: Registered protocol family 16
PCI: Using configuration type 1
PCI: Using MMCONFIG at e0000000
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20040326
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXH0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEX0.PXH1._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEY0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEZ0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIX._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 4 5 6 7 10 *11 14 15)
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xa9 -> IRQ 16 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:02.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:04.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 16 (level, low) -> IRQ 16
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb1 -> IRQ 19 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-23 -> 0xb9 -> IRQ 23 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xc1 -> IRQ 18 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xc9 -> IRQ 17 Mode:1 Active:1)
ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 17 (level, low) -> IRQ 17
IOAPIC[3]: Set PCI routing entry (5-0 -> 0xd1 -> IRQ 72 Mode:1 Active:1)
ACPI: PCI interrupt 0000:03:02.0[A] -> GSI 72 (level, low) -> IRQ 72
IOAPIC[1]: Set PCI routing entry (3-0 -> 0xd9 -> IRQ 24 Mode:1 Active:1)
ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 24 (level, low) -> IRQ 24
IOAPIC[1]: Set PCI routing entry (3-1 -> 0xe1 -> IRQ 25 Mode:1 Active:1)
ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 25 (level, low) -> IRQ 25
ACPI: PCI interrupt 0000:07:01.0[A] -> GSI 16 (level, low) -> IRQ 16
number of MP IRQ sources: 15.
number of IO-APIC #2 registers: 24.
number of IO-APIC #3 registers: 24.
number of IO-APIC #4 registers: 24.
number of IO-APIC #5 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 001 01 0 0 0 0 0 1 1 51
06 001 01 0 0 0 0 0 1 1 59
07 001 01 0 0 0 0 0 1 1 61
08 001 01 0 0 0 0 0 1 1 69
09 001 01 0 1 0 0 0 1 1 71
0a 001 01 0 0 0 0 0 1 1 79
0b 001 01 0 0 0 0 0 1 1 81
0c 001 01 0 0 0 0 0 1 1 89
0d 001 01 0 0 0 0 0 1 1 91
0e 001 01 0 0 0 0 0 1 1 99
0f 001 01 0 0 0 0 0 1 1 A1
10 001 01 1 1 0 1 0 1 1 A9
11 001 01 1 1 0 1 0 1 1 C9
12 001 01 1 1 0 1 0 1 1 C1
13 001 01 1 1 0 1 0 1 1 B1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 001 01 1 1 0 1 0 1 1 B9
IO APIC #3......
.... register #00: 03000000
....... : physical APIC id: 03
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00178020
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 D9
01 001 01 1 1 0 1 0 1 1 E1
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #4......
.... register #00: 04000000
....... : physical APIC id: 04
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 04000000
....... : arbitration: 04
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IO APIC #5......
.... register #00: 05000000
....... : physical APIC id: 05
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 05000000
....... : arbitration: 05
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 1 1 0 1 0 1 1 D1
01 000 00 1 0 0 0 0 0 0 00
02 000 00 1 0 0 0 0 0 0 00
03 000 00 1 0 0 0 0 0 0 00
04 000 00 1 0 0 0 0 0 0 00
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 000 00 1 0 0 0 0 0 0 00
08 000 00 1 0 0 0 0 0 0 00
09 000 00 1 0 0 0 0 0 0 00
0a 000 00 1 0 0 0 0 0 0 00
0b 000 00 1 0 0 0 0 0 0 00
0c 000 00 1 0 0 0 0 0 0 00
0d 000 00 1 0 0 0 0 0 0 00
0e 000 00 1 0 0 0 0 0 0 00
0f 000 00 1 0 0 0 0 0 0 00
10 000 00 1 0 0 0 0 0 0 00
11 000 00 1 0 0 0 0 0 0 00
12 000 00 1 0 0 0 0 0 0 00
13 000 00 1 0 0 0 0 0 0 00
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 000 00 1 0 0 0 0 0 0 00
17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ23 -> 0:23
IRQ24 -> 1:0
IRQ25 -> 1:1
IRQ72 -> 3:0
.................................... done.
Simple Boot Flag at 0x39 set to 0x1
IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 128Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4300 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 152k freed
vesafb: probe of vesafb0 failed with error -6
NET: Registered protocol family 1
SCSI subsystem initialized
libata version 1.02 loaded.
ata_piix version 1.02
ata_piix: combined mode detected
ACPI: PCI interrupt 0000:00:1f.2[A] -> GSI 18 (level, low) -> IRQ 18
PCI: Setting latency timer of device 0000:00:1f.2 to 64
ata1: PATA max UDMA/33 cmd 0x1F0 ctl 0x3F6 bmdma 0x1470 irq 14
ata1: dev 1 cfg 49:0f00 82:4210 83:4000 84:4000 85:0000 86:0000 87:4000
88:0407
ata1: dev 1 ATAPI, max UDMA/33
ata1: dev 1 configured for UDMA/33
scsi0 : ata_piix
Using anticipatory io scheduler
ata2: SATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0x1478 irq 15
ata2: dev 0 cfg 49:2f00 82:746b 83:7f01 84:4023 85:7469 86:3c01 87:4023
88:207f
ata2: dev 0 ATA, max UDMA/133, 488397168 sectors: lba48
ata2: dev 0 configured for UDMA/133
scsi1 : ata_piix
Vendor: ATA Model: WDC WD2500JS-00N Rev: 10.0
Type: Direct-Access ANSI SCSI revision: 05
ACPI: Processor [CPU0] (supports C1)
ACPI: Processor [CPU1] (supports C1)
ACPI: Processor [CPU2] (supports C1)
ACPI: Processor [CPU3] (supports C1)
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: Intel Corp. 6300ESB USB Universal Host Controller
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: irq 16, io base 0000000000001400
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: Intel Corp. 6300ESB USB Universal Host Controller
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: irq 19, io base 0000000000001420
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: Intel Corp. 6300ESB USB2 Enhanced Host Controller
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: irq 23, pci mem ffffff0010018400
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 3
PCI: cache line size of 128 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 4 ports detected
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
vga16fb: initializing
vga16fb: mapped to 0x00000100000a0000
fb0: VGA16 VGA frame buffer device
Console: switching to colour frame buffer device 80x30
inserting floppy driver for 2.6.8-11-em64t-p4-smp
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ide0: I/O resource 0x1F0-0x1F7 not free.
ide0: ports already in use, skipping probe
ide1: I/O resource 0x170-0x177 not free.
ide1: ports already in use, skipping probe
e1000: Ignoring new-style parameters in presence of obsolete ones
Intel(R) PRO/1000 Network Driver - version 5.2.52-k4
Copyright (c) 1999-2004 Intel Corporation.
ACPI: PCI interrupt 0000:06:01.0[A] -> GSI 24 (level, low) -> IRQ 24
e1000: eth0: e1000_probe: Intel(R) PRO/1000 Network Connection
ACPI: PCI interrupt 0000:06:02.0[A] -> GSI 25 (level, low) -> IRQ 25
e1000: eth1: e1000_probe: Intel(R) PRO/1000 Network Connection
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
SCSI device sda: 488397168 512-byte hdwr sectors (250059 MB)
SCSI device sda: drive cache: write back
/dev/scsi/host1/bus0/target0/lun0: p1 p2 < p5 p6 p7 p8 p9 >
Attached scsi disk sda at scsi1, channel 0, id 0, lun 0
Generic RTC Driver v1.07
input: ImPS/2 Generic Wheel Mouse on isa0060/serio1
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 6024332k swap on /dev/sda7. Priority:-1 extents:1
EXT3 FS on sda1, internal journal
3ware 9000 Storage Controller device driver for Linux v2.26.02.001.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda9, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda8, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda5, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
hw_random: RNG not detected
e1000: eth0: e1000_watchdog: NIC Link is Up 100 Mbps Full Duplex
NET: Registered protocol family 10
Disabled Privacy Extensions on device ffffffff8033e840(lo)
IPv6 over IPv4 tunneling driver
eth0: no IPv6 routers present
Reply to: