Re: Hard drive bad sector warning
smartctl -a /dev/sda output
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: WDC WD7500BPKT-60PK4T0
Serial Number: WD-WX31E1177192
Firmware Version: 01.01A01
User Capacity: 750,156,374,016 bytes
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 8
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sat Sep 10 00:46:56 2011 EST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection: Disabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (12960) seconds.
Offline data collection
capabilities: (0x51) SMART execute Offline immediate.
No Auto Offline data collection support.
Suspend Offline collection upon new
command.
No Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 129) minutes.
SCT capabilities: (0x703d) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 199 172 051 Pre-fail Always - 751
3 Spin_Up_Time 0x0027 190 177 021 Pre-fail Always - 1500
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 137
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
9 Power_On_Hours 0x0032 100 100 000 Old_age Always - 315
10 Spin_Retry_Count 0x0033 100 100 051 Pre-fail Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 126
183 Runtime_Bad_Block 0x0032 100 100 000 Old_age Always - 0
184 End-to-End_Error 0x0033 100 100 097 Pre-fail Always - 0
187 Reported_Uncorrect 0x0032 001 001 000 Old_age Always - 913
188 Command_Timeout 0x0032 100 100 000 Old_age Always - 0
190 Airflow_Temperature_Cel 0x0022 059 045 040 Old_age Always - 41 (Lifetime Min/Max 22/43)
191 G-Sense_Error_Rate 0x0032 001 001 000 Old_age Always - 127
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 2
193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 2187
194 Temperature_Celsius 0x0022 106 092 000 Old_age Always - 41
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 1
198 Offline_Uncorrectable 0x0030 100 253 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail Offline - 0
SMART Error Log Version: 1
ATA Error Count: 669 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 669 occurred at disk power-on lifetime: 312 hours (13 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 93 71 e8 Error: UNC 8 sectors at LBA = 0x087193d0 = 141661136
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 93 71 e8 08 04:16:42.058 READ DMA
ec 00 00 00 00 00 a0 08 04:16:42.048 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:16:42.045 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 04:16:42.036 IDENTIFY DEVICE
c8 00 08 d0 93 71 e8 08 04:16:40.136 READ DMA
Error 668 occurred at disk power-on lifetime: 312 hours (13 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 93 71 e8 Error: UNC 8 sectors at LBA = 0x087193d0 = 141661136
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 93 71 e8 08 04:16:40.136 READ DMA
ec 00 00 00 00 00 a0 08 04:16:40.128 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:16:40.128 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 04:16:40.121 IDENTIFY DEVICE
c8 00 08 d0 93 71 e8 08 04:16:38.221 READ DMA
Error 667 occurred at disk power-on lifetime: 312 hours (13 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 93 71 e8 Error: UNC 8 sectors at LBA = 0x087193d0 = 141661136
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 93 71 e8 08 04:16:38.221 READ DMA
ec 00 00 00 00 00 a0 08 04:16:38.212 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:16:38.205 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 04:16:38.198 IDENTIFY DEVICE
c8 00 08 d0 93 71 e8 08 04:16:36.299 READ DMA
Error 666 occurred at disk power-on lifetime: 312 hours (13 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 93 71 e8 Error: UNC 8 sectors at LBA = 0x087193d0 = 141661136
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 93 71 e8 08 04:16:36.299 READ DMA
ec 00 00 00 00 00 a0 08 04:16:36.290 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:16:36.283 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 04:16:36.275 IDENTIFY DEVICE
c8 00 08 d0 93 71 e8 08 04:16:34.381 READ DMA
Error 665 occurred at disk power-on lifetime: 312 hours (13 days + 0 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 08 d0 93 71 e8 Error: UNC 8 sectors at LBA = 0x087193d0 = 141661136
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
c8 00 08 d0 93 71 e8 08 04:16:34.381 READ DMA
ec 00 00 00 00 00 a0 08 04:16:34.373 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 08 04:16:34.365 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 08 04:16:34.360 IDENTIFY DEVICE
c8 00 08 d0 93 71 e8 08 04:16:32.451 READ DMA
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Short offline Completed without error 00% 102 -
# 2 Short offline Completed without error 00% 100 -
# 3 Extended offline Completed without error 00% 83 -
# 4 Short offline Completed without error 00% 81 -
# 5 Short offline Completed: read failure 90% 70 229181752
# 6 Short offline Completed: read failure 90% 67 229181752
# 7 Short offline Completed: read failure 90% 67 229181752
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
--
Kind regards,
Yudi
Reply to: