Asus P5K WS motherboard / Marvell IDE - CDrom not detected by installer
Hi Folks,
I'm using the latest debian-testing-amd64-businesscard installer on an
Asus P5K motherboard with an ICH9 Southbridge and Marvell 88SE61xx SATA /
PATA chipset. I'm using an HP dvd1040i CDrom drive for installation.
The installer boots fine but cannot find any cdrom device to use. When I
look at dmesg, I get the following output relating to the ide devices:
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHZ system bus speed for PIO modes; override with
idebus=xx
pnp: the driver 'ide' has been registered
ata_piix: 0000:00:1f.2: version 2.10ac1
ata_piix: 0000:00:1f.2: MAP [ P0 P2 P1 P3 ]
ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x00000000000103f6
bmdma 0x000000000001ff90 irq 14
ata1: SATA max UDMA/133 cmd 0x00000000000101f0 ctl 0x0000000000010376
bmdma 0x000000000001ff98 irq 15
scsi0: ata_piix
ata1.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi1: ata_piix
ata2.00: ATA-7: ST3500630AS, 3.AAK, max UDMA/133
ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi: 0:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
scsi: 1:0:0:0: Direct-Access ATA ST3500630AS 3.AA PQ: 0 ANSI: 5
ata_piix 0000:00:1f.5: MAP [ P0 P2 P1 P3 ]
ata3: SATA max UDMA/133 cmd 0x000000000001a000 ctl 0x0000000000019c02
bmdma 0x0000000000019480 irq 22
ata4: SATA max UDMA/133 cmd 0x0000000000019880 ctl 0x0000000000019802
bmdma 0x0000000000019488 irq 22
scsi2: ata_piix
ATA: abnormal status 0x7F on port 0x000000000001a007
scsi3: ata_piix
ATA: abnormal status 0x7F on port 0x0000000000019887
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sda: unknown partition table
sd: 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't
support DPO or FUA
sdb: unknown partition table
sd: 1:0:0:0: Attached scsi disk sdb
ide0: I/O resource 0x3F6-0x3F6 not free.
ide0: ports already in use, skipping probe
ide1: I/O resource 0x376-0x376 not free.
ide1: ports already in use, skipping probe
an lspci yields the following IDE devices:
00:1f.2 IDE interface: Intel Corporation Unknown device 2920 (rev 02)
(prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 22
I/O ports at 01f0 [size=8]
I/O ports at 03f4 [size=1]
I/O ports at 0170 [size=8]
I/O ports at 0374 [size=1]
I/O ports at ff90 [size=16]
I/O ports at ffa0 [size=16]
Capabilities: [70] Power Management version 3
Capabilities: [b0] Vendor Specific Information
00:1f.5 IDE interface: Intel Corporation Unknown device 2926 (rev 02)
(prog-if 85 [Master SecO PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 8277
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 22
I/O ports at a000 [size=8]
I/O ports at 9c00 [size=4]
I/O ports at 9880 [size=8]
I/O ports at 9800 [size=4]
I/O ports at 9480 [size=16]
I/O ports at 9400 [size=16]
Capabilities: [70] Power Management version 3
Capabilities: [b0] Vendor Specific Information
01:00.0 IDE interface: Marvell Technology Group Ltd. Unknown device 6121
(rev b1) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: ASUSTeK Computer Inc. Unknown device 8296
Flags: bus master, fast devsel, latency 0, IRQ 10
I/O ports at bc00 [size=8]
I/O ports at b880 [size=4]
I/O ports at b800 [size=8]
I/O ports at b480 [size=16]
I/O ports at b400 [size=16]
Memory at fe7ffc00 (32-bit, non-prefetchable) [size=1K]
Capabilities: [48] Power Management version 2
Capabilities: [50] Messsage Signalled Interrupts: Mask- 64bit- Queue=0/0
Enable-
Capabilities: [e0] Express Legacy Endpoint IRQ 0
So it looks like my 2 hard drives are showing up just fine, but I'm fairly
clueless as to why the kernel (2.6.21-2-amd64) isn't finding the CDrom
drive.
I've verified that the Marvell IDE/eSATA controller is enabled in the BIOS
as well (hence the initial booting of the installer CD).
I'm hoping someone on the list can point me in the right direction; if
this isn't the appropriate list then please accept my apologies for the
noise.
Thanks in advance,
-Mike.
==================================================================
Mike Messick Dona nobis pacem rm -rf /bin/laden
PGP Key Fingerprint: email: mikem@alaska.net
2048/0x57318496 053B 412B 82FC 3808 E141 CDCD 74AE 01C5 5731 8496
Reply to: