[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

X (Svirge GX/2 Or Monitor)? problem



Hi,

I have been trying every where but keep hitting dead ends for the past 4 - 5 months... in other areas on web etc (Hack, hack, hack)

(I accept I don't know what I'm doing but I posted a log file below)

I have an ADI Provist monitor CD 484  (Which I can't find any specs for ... So how can I determine the Hsync / Vsync  - even the readme requires you to know some specs and there is no documentation on this monitor)

I have taken xdm out of /etc/init.d and since then I don't get a log file any more for errors...  can anyone help?

I have potato installed and also woody available but I thought I should at least get something  working.  What should I do?


TIA
Kim

******************
20021206
******************

XFree86 Version 3.3.6 / X Window System
(protocol Version 11, revision 0, vendor release 6300)
Release Date: January 8 2000
	If the server is older than 6-12 months, or if your card is newer
	than the above date, look for a newer version before reporting
	problems.  (see http://www.XFree86.Org/FAQ)
Operating System: Linux 2.2.14-va.4.4-i586 i686 [ELF] 
Configured drivers:
  S3V: accelerated server for S3 graphics adaptors (Patchlevel 0)
      s3_ViRGE
(using VT number 7)

XF86Config: /usr/X11R6/lib/X11/XF86Config
(**) stands for supplied, (--) stands for probed/default values
(**) XKB: keymap: "xfree86(en_US)" (overrides other XKB settings)
(**) Mouse: type: PS/2, device: /dev/psaux, buttons: 3
(**) S3V: Graphics device ID: "S3VirgeGX"
(**) S3V: Monitor ID: "AdiProVista"
(--) S3V: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) S3V: Mode "1280x1024" needs hsync freq of 29.21 kHz. Deleted.
(--) S3V: Mode "1280x1024" needs vert refresh rate of 33.25 Hz. Deleted.
(--) S3V: Mode "1280x1024" needs vert refresh rate of 38.79 Hz. Deleted.
(--) S3V: Mode "1280x1024" needs vert refresh rate of 44.33 Hz. Deleted.
(--) S3V: Mode "1280x1024" needs vert refresh rate of 49.88 Hz. Deleted.
(--) S3V: Mode "1280x1024" needs hsync freq of 70.09 kHz. Deleted.
(--) S3V: Mode "1280x1024" needs hsync freq of 74.59 kHz. Deleted.
(--) S3V: Mode "1280x1024" needs hsync freq of 78.86 kHz. Deleted.
(--) S3V: Mode "1280x1024" needs hsync freq of 81.13 kHz. Deleted.
(--) S3V: Mode "1280x1024" needs hsync freq of 107.16 kHz. Deleted.
(**) FontPath set to "/usr/X11R6/lib/X11/fonts/misc/:unscaled,/usr/X11R6/lib/X11/fonts/cyrillic/:unscaled,/usr/X11R6/lib/X11/fonts/100dpi/:unscaled,/usr/X11R6/lib/X11/fonts/75dpi/:unscaled,/usr/X11R6/lib/X11/fonts/Speedo/,/usr/X11R6/lib/X11/fonts/Type1/,/usr/X11R6/lib/X11/fonts/misc/,/usr/X11R6/lib/X11/fonts/cyrillic/,/usr/X11R6/lib/X11/fonts/100dpi/,/usr/X11R6/lib/X11/fonts/75dpi/"
(--) S3V: PCI: ViRGE/GX2 rev 6, Linear FB @ 0xe0000000
(--) S3V: chipset:   ViRGE/GX2 rev. 6
(--) S3V: chipset driver: s3_ViRGE
(**) S3V: videoram:  4096k
(--) S3V: Ramdac type: s3_trio64
(--) S3V: Ramdac speed: 170 MHz
(--) S3V: Using Trio32/64 programmable clock (MCLK 75.886 MHz)
(--) S3V: Maximum allowed dot-clock: 170.000 MHz
(**) S3V: Mode "1280x1024": mode clock = 110.000
(--) S3V: Operating RAMDAC in pixel multiplex mode
(--) S3V: Using 6 bits per RGB value
(--) S3V: Virtual resolution set to 1280x1024
(--) S3V: Local bus LAW is 0xE00xxxxx
(--) S3V: Using a banksize of 4096k, line width of 1280
System: `/usr/X11R6/lib/X11/xkb/xkbcomp -w 1 -R/usr/X11R6/lib/X11/xkb -xkm -m en_US -em1 "The XKEYBOARD keymap compiler (xkbcomp) reports:" -emp "> " -eml "Errors from xkbcomp are not fatal to the X server" keymap/xfree86 compiled/xfree86.xkm'
****************************
20021206
****************************






Reply to: