Re: how do i create device ppp0 on commandline?
Sorry I don't know what superrescue is... Maybe you should just
download the newest rp-pppoe - I have rp-pppoe-3.5 from
roaringpenguin.com. It will make a pppoe.conf for you. What is the
output of #dmesg?
Here is mine (the relevant parts), but be aware I have the support
compiled into the kernel, not as loadable modules... You can also run
lsmod and see if you have the ppp drivers loaded, to me it looks like
you are up and running ok, though, I can ping you (I think that is you
at 213.13.200.110), try to confirm your DNS setting.
#dmesg ---relevant portions---
Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
PCI: Found IRQ 9 for device 00:09.0
tulip0: MII transceiver #1 config 3000 status 7829 advertising 01e1.
eth0: Lite-On 82c168 PNIC rev 32 at 0xd8800000, 00:A0:CC:DA:AF:86, IRQ
9.
PCI: Found IRQ 9 for device 00:0a.0
tulip1: MII transceiver #1 config 3000 status 7809 advertising 01e1.
eth1: Lite-On 82c168 PNIC rev 32 at 0xd8802000, 00:A0:CC:D3:D5:C9, IRQ
9.
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
P.S. - you can try pinging me at 138.89.32.80
Shawn
--- el <nntps2net@t-online.de> wrote:
> thanks a lot for the reply!
>
>
> situation:
> i came to the point, that i need something like superrescue-cd.
> there is no default adsl dialup on it, as i know already.
> what i know for sure, is that RoaringPenguin-pppoe is implemented on
> that cd and rp-pppoe/adsl is a user space driver. So adsl-dialup must
> be
> available on superrescue.
>
> /usr/sbin/adsl-start
> gave
> cannot read configuration file /etc/ppp/pppoe.conf
>
> it's not there and no link to /etc/sysconf/network-scripts/ifcfg-ppp0
>
> either. i have a problem with that, because this should be the
> necessary
> config file for the rp-adsl-scripts. superrescue is built on rh7.2,
> it
> looks exactly the same on rh7.3(as well no link) but there it works!
> anyway, then i forget the scripts and try by hand:
>
> ifconfig eth0 up
> (i have validated sucessfull networking before)
> ifconfig ppp0 up
> ppp0: unknown interface: no such device
> pppoe -A eth0 => works as it should be!
> pppd pty 'pppoe -I eth0' => no error-reply
> ifconf => shows still only eth0
> ifconf ppp0 up => still no ppp0
>
> that's were i'm stuck right now.
> after i read the man pages.
> next would be getting any and all doc's about pppoe/adsl and reading
> the
> scripts, but i'm not confident on that.
> i would be really glad if you have any hint for me...
>
>
> el
>
>
> p.s. should have been sending this msg some hours before, to be as
> instant as you, but i tried and read and tried and ... you
> know...
>
>
> Shawn Lamson wrote:
> > you can start with #/sbin/ifconfig ppp0 up
> > But you will probably need to read the ifconfig man pages for more
> info
> > #man ifconfig
> > Let me know if that is what you wanted... if you are trying to use
> an
> > aDSL modem you may need a package like Roaring Penguin
> Point-to-Point
> > Protocol over Ethernet. Look at RoaringPenguin.com
> > HTH
> >
> > Shawn
> >
> > --- el <nntps2net@t-online.de> wrote:
> >
> >>hi,
> >>
> >>how do i create device ppp0
> >>(not on the rescue-cd-ramdisk per default)
> >>with commandline commands?
> >>
> >>thanks for your help!
> >>
> >>el
> >>
> >>
> >>
> >>--
> >>To UNSUBSCRIBE, email to debian-user-request@lists.debian.org
> >>with a subject of "unsubscribe". Trouble? Contact
> >>listmaster@lists.debian.org
> >>
> >
> >
> >
> > __________________________________________________
> > Do you Yahoo!?
> > New DSL Internet Access from SBC & Yahoo!
> > http://sbc.yahoo.com
> >
>
>
__________________________________________________
Do you Yahoo!?
New DSL Internet Access from SBC & Yahoo!
http://sbc.yahoo.com
Reply to: