Help requested: internal iomega atapi zip drive
I recently compiled (and recompiled and recompiled, etc) a new kernel,
2.4.18, hoping to be able to use my internal iomega atapi zip drive,
which I was able to use before I crashed my harddrive and had to
reinstall from scratch about a year ago.
I tried with jazip and scsi emulation enabled and ide/atapi disabled,
per the jazip faq: "...you need to turn on kernel support for "SCSI
emulation", "SCSI Support", and "SCSI Generic Support". You also need to
turn off "IDE/ATAPI Floppy Support"".
If I understand correctly, my zip drive should then show up as sda in
the boot messages, but I don't see it (and jazipconfig reports: no
device found)
I also tried the reverse, scsi support disabled ide/atapi
enabled. Should I then see a "hdc"?
In any event, I'm not sure what the ide0 or ide1 drives are? anything to
do with this.
Sorry for the question if there is an obvious answer, but I don't see
it. Any help very much appreciated by this SIMPLE END USER. Thanks (boot
messages follow),
Tomasz
BOOT MESSAGE WITH SCSI EMULATION ENABLED:
Aug 4 20:51:56 localhost kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
Aug 4 20:51:56 localhost kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Aug 4 20:51:56 localhost kernel: hda: Maxtor 32049H2, ATA DISK drive
Aug 4 20:51:56 localhost kernel: hdb: ATAPI CD-ROM DRIVE 36X MAXIMUM, ATAPI CD/DVD-ROM drive
Aug 4 20:51:56 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Aug 4 20:51:56 localhost kernel: hda: 40021632 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63
Aug 4 20:51:56 localhost kernel: hdb: ATAPI 36X CD-ROM drive, 128kB Cache, (U)DMA
Aug 4 20:51:56 localhost kernel: Uniform CD-ROM driver Revision: 3.12
Aug 4 20:51:56 localhost kernel: Partition check:
Aug 4 20:51:56 localhost kernel: hda: hda1 hda2 hda3
Aug 4 20:51:56 localhost kernel: Floppy drive(s): fd0 is 1.44M
Aug 4 20:51:56 localhost kernel: FDC 0 is a post-1991 82077
Aug 4 20:51:56 localhost kernel: plip: parport0 has no IRQ. Using IRQ-less mode,which is fairly inefficient!
Aug 4 20:51:56 localhost kernel: NET3 PLIP version 2.4-parport gniibe@mri.co.jp
Aug 4 20:51:56 localhost kernel: plip0: Parallel port at 0x378, not using IRQ.
Aug 4 20:51:56 localhost kernel: PPP generic driver version 2.4.1
Aug 4 20:51:56 localhost kernel: PPP Deflate Compression module registered
Aug 4 20:51:56 localhost kernel: Linux agpgart interface v0.99 (c) Jeff Hartmann
Aug 4 20:51:56 localhost kernel: agpgart: Maximum main memory to use for agp memory: 96M
Aug 4 20:51:56 localhost kernel: agpgart: Detected Intel 440BX chipset
Aug 4 20:51:56 localhost kernel: agpgart: AGP aperture is 64M @ 0xe0000000
Aug 4 20:51:56 localhost kernel: [drm] Initialized tdfx 1.0.0 20010216 on minor 0
Aug 4 20:51:56 localhost kernel: [drm] AGP 0.99 on Intel 440BX @ 0xe0000000 64MB
Aug 4 20:51:56 localhost kernel: [drm] Initialized radeon 1.1.1 20010405 on minor 1
Aug 4 20:51:56 localhost kernel: SCSI subsystem driver Revision: 1.00
Aug 4 20:51:56 localhost kernel: scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Aug 4 20:51:56 localhost kernel: es1371: version v0.30 time 20:36:27 Aug 4 2002
Aug 4 20:51:56 localhost kernel: usb.c: registered new driver usbdevfs
Aug 4 20:51:56 localhost kernel: usb.c: registered new driver hub
Aug 4 20:51:56 localhost kernel: uhci.c: USB Universal Host Controller Interface driver v1.1
Aug 4 20:51:56 localhost kernel: uhci.c: USB UHCI at I/O 0xe000, IRQ 10
Aug 4 20:51:56 localhost kernel: usb.c: new USB bus registered, assigned bus number 1
Aug 4 20:51:56 localhost kernel: hub.c: USB hub found
Aug 4 20:51:56 localhost kernel: hub.c: 2 ports detected
******************************************
BOOT MESSAGE WITH IDE/ATAPI ENABLED:
Aug 5 20:41:08 localhost kernel: ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
Aug 5 20:41:08 localhost kernel: ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
Aug 5 20:41:08 localhost kernel: hda: Maxtor 32049H2, ATA DISK drive
Aug 5 20:41:08 localhost kernel: hdb: ATAPI CD-ROM DRIVE 36X MAXIMUM, ATAPI CD/DVD-ROM drive
Aug 5 20:41:08 localhost kernel: ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Aug 5 20:41:08 localhost kernel: hda: 40021632 sectors (20491 MB) w/2048KiB Cache, CHS=2491/255/63
Aug 5 20:41:08 localhost kernel: hdb: ATAPI 36X CD-ROM drive, 128kB Cache, (U)DMA
Aug 5 20:41:08 localhost kernel: Uniform CD-ROM driver Revision: 3.12
Aug 5 20:41:08 localhost kernel: ide-floppy driver 0.97.sv
Aug 5 20:41:08 localhost kernel: Partition check:
Aug 5 20:41:08 localhost kernel: hda: hda1 hda2 hda3
Aug 5 20:41:08 localhost kernel: Floppy drive(s): fd0 is 1.44M
Aug 5 20:41:08 localhost kernel: FDC 0 is a post-1991 82077
Aug 5 20:41:08 localhost kernel: plip: parport0 has no IRQ. Using IRQ-less mode,which is fairly inefficient!
Reply to: