Re: cdrecord problems
Drive is scsi, adapter is adaptec aha02940. Never
had problems before. I attached a log using script instead
of just redirecting the output.
On Mon, 7 Jan 2002, martin f krafft wrote:
> also sprach Russ Cook <russcook@flash.net> [2002.01.07.0013 +0100]:
> > log with -vv is attached
>
> mh... no extra info...
>
> is this an IDE or a SCSI drive? and if IDE, are you using ide-scsi.o?
>
> --
> martin; (greetings from the heart of the sun.)
> \____ echo mailto: !#^."<*>"|tr "<*> mailto:"; net@madduck
>
> give me ambiguity or give me something else.
>
Script started on Sun Jan 6 17:33:32 2002
p90:/home/russ# cdrecord -vv /scsi1/debian.raw dev=0,3,0
Cdrecord 1.10 (i586-pc-linux-gnu) Copyright (C) 1995-2001 Jörg Schilling
TOC Type: 1 = CD-ROM
scsidev: '0,3,0'
scsibus: 0 target: 3 lun: 0
Linux sg driver version: 2.1.39
Using libscg version 'schily-0.5'
Using libscg transport code version 'schily-scsi-linux-sg.c-1.66'
atapi: 0
Device type : Removable CD-ROM
Version : 2
Response Format: 2
Capabilities : SYNC
Vendor_info : 'YAMAHA '
Identifikation : 'CRW4416S '
Revision : '1.0g'
Device seems to be: Generic mmc CD-RW.
Using generic SCSI-3/mmc CD-R driver (mmc_cdr).
Driver flags : SWABAUDIO
Drive buf size : 1566432 = 1529 KB
FIFO size : 4194304 = 4096 KB
Track 01: data 562 MB
track: 1 start: 0 pregap: 150
Total size: 645 MB (63:58.53) = 287890 sectors
Lout start: 646 MB (64:00/40) = 287890 sectors
41 00 00 14 00 00 00 00
41 01 00 10 00 00 00 00
41 01 01 10 00 00 02 00
41 AA 01 14 00 40 00 28
Current Secsize: 2048
ATIP info from disk:
Indicated writing power: 6
Reference speed: 2
Is not unrestricted
Is erasable
ATIP start of lead in: -11078 (97:34/22)
ATIP start of lead out: 336075 (74:43/00)
speed low: 0 speed high: 4
power mult factor: 3 5
recommended erase/write power: 3
A2 values: 5C C6 26
Disk type: Phase change
Manuf. index: 11
Manufacturer: Mitsubishi Chemical Corporation
Blocks total: 336075 Blocks current: 336075 Blocks remaining: 48185
Starting to write CD/DVD at speed 4 in write mode for single session.
Last chance to quit, starting real write in 9 seconds.8 seconds.7 seconds.6 seconds.5 seconds.4 seconds.3 seconds.2 seconds.1 seconds.0 seconds. Operation starts.
Waiting for reader process to fill input buffer ... input buffer ready.
Performing OPC...
Starting new track at sector: 0
Track 01: 0 of 562 MB written.cdrecord: Input/output error. write_g1: scsi sendcmd: no error
CDB: 2A 00 00 00 00 00 00 00 1F 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 00 29 00 00 00
Sense Key: 0x6 Unit Attention, Segment 0
Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 43.033s timeout 40s
write track data: error after 0 bytes
Sense Bytes: 70 00 00 00 00 00 00 0A 00 00 00 00 00 00 00 00 00 00
Writing time: 67.577s
Fixating...
cdrecord: Input/output error. close track/session: scsi sendcmd: no error
CDB: 5B 00 02 00 00 00 00 00 00 00
status: 0x2 (CHECK CONDITION)
Sense Bytes: 70 00 05 00 00 00 00 0A 00 00 00 00 2C 04 00 00
Sense Key: 0x5 Illegal Request, Segment 0
Sense Code: 0x2C Qual 0x04 (current program area is empty) Fru 0x0
Sense flags: Blk 0 (not valid)
cmd finished after 0.002s timeout 480s
cmd finished after 0.002s timeout 480s
Fixating time: 0.006s
cdrecord: fifo had 64 puts and 1 gets.
cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
p90:/home/russ# exit
Script done on Sun Jan 6 17:35:20 2002
Reply to: