Anyone help set up Iomega ZIP drive please?
I have installed an Iomega ZIP 100 parallel drive and it works under DOS. I
have read the HOWTO but there seem to be some differences relative to the
latest kernel (2.2.5), which I'm using.
I've compiled in SCSI support, SCSI Disk support, and IOMEGA parallel
support (which I think is unnecessary). None of these are modules and I
don't want to use modules if I can avoid it.
On boot, I get the following messages:
---------------cut-----------------
Linux version 2.2.5 (root@achc.demon.co.uk) (gcc version 2.7.2.3) #17 Thu Apr 1 15:08:32 BST 1999
Detected 233289274 Hz processor.
Console: colour VGA+ 80x30
Calibrating delay loop... 232.65 BogoMIPS
Memory: 30892k/32768k available (892k kernel code, 408k reserved, 536k data, 40k init)
CPU: Intel Pentium II (Deschutes) stepping 02
Checking 386/387 coupling... OK, FPU using exception 16 error reporting.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.26 (19981001) Richard Gooch (rgooch@atnf.csiro.au)
PCI: PCI BIOS revision 2.10 entry at 0xfedc7
PCI: Using configuration type 1
PCI: Probing PCI hardware
Linux NET4.0 for Linux 2.2
Based upon Swansea University Computer Society NET3.039
NET4: Unix domain sockets 1.0 for Linux NET4.0.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
Starting kswapd v 1.5
parport0: PC-style at 0x378 [SPP,ECP,ECPPS2]
parport0: detected irq 7; use procfs to enable interrupt-driven operation.
Detected PS/2 Mouse Port.
Serial driver version 4.27 with no serial options enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
pty: 256 Unix98 ptys configured
lp0: using parport0 (polling).
apm: BIOS version 1.2 Flags 0x02 (Driver version 1.9)
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfe60-0xfe67, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xfe68-0xfe6f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK4310MAT, ATA DISK drive
hdc: CD-224E, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: TOSHIBA MK4310MAT, 4126MB w/0kB Cache, CHS=526/255/63, UDMA
hdc: ATAPI 24X CD-ROM drive, 128kB Cache
Uniform CDROM driver Revision: 2.54
Floppy drive(s): fd0 is 1.44M
FDC 0 is an 8272A
imm: Version 2.03 (for Linux 2.0.0)
scsi : 0 hosts.
scsi : detected total.
PPP: version 2.3.3 (demand dialling)
TCP compression code copyright 1989 Regents of the University of California
PPP line discipline registered.
Partition check:
hda: hda2 hda3 hda4
VFS: Mounted root (ext2 filesystem) readonly.
Freeing unused kernel memory: 40k freed
Adding Swap: 80288k swap-space (priority -1)
TIOCSER?WILD ioctl obsolete, ignored.
TIOCSER?WILD ioctl obsolete, ignored.
registered device ppp0
---------------------------cut--------------------------------------
It looks as if the scsi interface has been detected but I don't know if
this is enough or what to do next. Can anyone help please?
Anthony
--
Anthony Campbell - running Linux Debian 2.1
acampbell@achc.demon.co.uk http://www.achc.demon.co.uk
"The Moving Finger writes; and, having writ,
Moves on..." - Edward Fitzgerald (Rubaiat of Omar Khayyam)
Reply to: