debian 1.3 & 3c905 boomerang
Hi,
I've just installed a debian 1.3, and booting with boot disk eth0 3c905 is not recognized.
So installed with dselect 2.0.30 kernel image and i copie it onto the boot floppy.
Nothing changed.
The strange thing, is that i've already installe debian 1.3 on e pc with 3c905.
this is the dmesg:
ole (max 63)
pcibios_init : BIOS32 Service Directory structure at 0x000fdb70
pcibios_init : BIOS32 Service Directory entry at 0xfdb80
pcibios_init : PCI BIOS revision 2.10 entry at 0xfdba1
Probing PCI hardware.
Warning : Unknown PCI device (10b7:9050). Please read include/linux/pci.h
Warning : Unknown PCI device (1000:f). Please read include/linux/pci.h
Calibrating delay loop.. ok - 199.07 BogoMIPS
Memory: 62736k/65536k available (1008k kernel code, 384k reserved, 1408k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.30 (herbert@greathan) (gcc version 2.7.2.2) #1 Sun Jun 1 09:14:11 EST 1997
Real Time Clock Driver v1.07
tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $
tpqic02: DMA buffers: 20 blocks, at address 0x24ea00 (0x24e914)
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
ide: i82371 PIIX (Triton) on PCI bus 0 function 57
ide0: BM-DMA at 0xffa0-0xffa7
hdb: FX810S, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
Started kswapd v 1.4.2.2
FDC 0 is a post-1991 82077
md driver 0.35 MAX_MD_DEV=4, MAX_REAL=8
ncr53c8xx : at PCI bus 0, device 11, function 0
ncr_attach: unit=0 chip=875 base=febeff00, io_port=ec00, irq=11
ncr53c875-0: using memory mapped IO at virtual address 0x4805f00
ncr53c875-0: initial value of SCNTL3 = 55, final = 35
ncr53c875-0: requesting shared irq 11 (dev_id=0x90068)
ncr53c875-0: restart (scsi reset).
Failed initialization of WD-7000 SCSI card!
PPA: unable to initialise controller at 0x378, error 2
scsi0 : ncr53c8xx (rel 1.12d)
scsi : 1 host.
Vendor: IBM Model: DORS-32160W Rev: WA6A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
Vendor: IBM Model: DORS-32160W Rev: WA0A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdb at scsi0, channel 0, id 1, lun 0
Vendor: IBM Model: DORS-32160W Rev: WA6A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdc at scsi0, channel 0, id 2, lun 0
Vendor: IBM Model: DORS-32160W Rev: WA0A
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sdd at scsi0, channel 0, id 3, lun 0
scsi : detected 4 SCSI disks total.
ncr53c875-0-<target 0, lun 0>: WIDE SCSI (16 bit) enabled.
ncr53c875-0-<target 0, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
ncr53c875-0-<target 1, lun 0>: WIDE SCSI (16 bit) enabled.
ncr53c875-0-<target 1, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8.
SCSI device sdb: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
ncr53c875-0-<target 2, lun 0>: WIDE SCSI (16 bit) enabled.
ncr53c875-0-<target 2, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8.
SCSI device sdc: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
ncr53c875-0-<target 3, lun 0>: WIDE SCSI (16 bit) enabled.
ncr53c875-0-<target 3, lun 0>: FAST SCSI-2 100ns (20 Mb/sec) offset 8.
SCSI device sdd: hdwr sector= 512 bytes. Sectors= 4226725 [2063 MB] [2.1 GB]
Partition check:
sda: sda1
sdb: sdb1
sdc: sdc1
sdd: sdd1 sdd2 sdd3 sdd4
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 130748k swap-space (priority -1)
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
PS/2 auxiliary pointing device detected -- driver installed.
maybe is there an interrupt conflict between eth0 and scsi?
thnx in advance!
Maurizio Marini
Amm.ne Prov.le di Pesaro e Urbino
Via Gramsci, 4
61100 - Pesaro (Italy)
Tel. +39 (721) 359390
Fax +39 (721) 359350
p. Iva 00212000418
--
TO UNSUBSCRIBE FROM THIS MAILING LIST: e-mail the word "unsubscribe" to
debian-user-request@lists.debian.org .
Trouble? e-mail to templin@bucknell.edu .
Reply to: