Merhaba,
Debian unstable kullaniyorum.
2 gündür bilgisayarı dual display yapmaya uğraşıyorum. normalde on-board
geforce-4 mx ekran kartım vardı
fakat bu kartta ikinci monitor baglamak icin asus av/s diye bir parça
gerekiyormuş ve bulamadım.
bende arkadaşımdan aldığım Matrox G400 ü taktım. gerekli ayarları yaptım
dual display sorunsuz çalışıyor.
ancak ben bunu yapana kadar heralde bir 40-50 kere bilgisayar kitlendi ve
restart atınca kernel panic verdi ! cidden abartmıyorum. Sürekli
kernel-panic hatası alıyorum.
Ve debian ın en sevdiğim yönü işte knoppixle sistemi aciyoruz knoppix in
kernelini bilgisayara kopyalıyoruz
grub a gerekli girdileri veriyoruz daha sonra sistemi bununla açıyoruz ve
apt-get install kernel-image-2.6.6-1-k7 . bilgisayar yeniden açılıyor. ama
anlamadığım bir şekilde yeniden
kitleniyor. üst üste gelen restartlardan kde iyice dailiyor apt-get
reinstall kde
filesystem kendini şaşırıyor e2fsck .... ve debian aslan gibi yıkılmıyor
ve hala çalışıcam diye çabalıyor.
bu işlemleri 2 gündür kaç kere yaptığımı sayamadım.
Şimdi bu durumda sorun neden kaynaklanabilir ?
a) Dual Display ve Xinerama ile kullanılan XFree86
b) 300 wattlık güç kaynağı
amd athlon 2600+
1gb ddr 400 ram
1 cd yazıcı 1 dvd-okuyucu
2 hdd biri 120 dieri 40 seagate 7200rpm
tv karti
2 ethernet kartı biri on-board
Matrox G400 ekran kartı
Sounblaster live platinum ses kartı birde cdrom yerine takılan üstünde
midi spdif girişleri olan live drive zımbırtısı var
Anakart Asus A7n8x-vm nforce chipsetli on-board ekran-ses-lan var
bu donanımla 300 wattlık güç kaynağı sorun yaratabilir mi kasa aopen
c) Matrox ekran kartını yolda getirirken bozdum. ya da driveri problemli.
Sitesinde verilen driver ı da XFree86 dakini de denedim.
d) Diğer problemler
yardımlarınız için şimdiden teşekkürler
XFree86.log ektedir başka bir log ya da conf dosyasi isterseniz göndereyim.
dmesg
oport range 0xcf8-0xcff could not be reserved
pnp: 00:0a: ioport range 0x480-0x4ff could not be reserved
PNPBIOS fault.. attempting recovery.
PnPBIOS: Warning! Your PnP BIOS caused a fatal error. Attempting to
continue
PnPBIOS: You may need to reboot with the "nobiospnp" option to operate
stably
PnPBIOS: Check with your vendor for an updated BIOS
PnPBIOS: get_dev_node: unexpected status 0x28
PnPBIOS: 13 nodes reported by PnP BIOS; 13 recorded by driver
ACPI: PCI Interrupt Link [LKSM] BIOS reported IRQ 22, using IRQ 23
ACPI: PCI Interrupt Link [LKSM] enabled at IRQ 23
00:00:01[A] -> 1-23 -> IRQ 23 level high
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
00:00:04[A] -> 1-22 -> IRQ 22 level high
ACPI: PCI Interrupt Link [LAPU] enabled at IRQ 21
00:00:05[A] -> 1-21 -> IRQ 21 level high
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 20
00:00:06[A] -> 1-20 -> IRQ 20 level high
ACPI: PCI Interrupt Link [LKMO] enabled at IRQ 22
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
ACPI: PCI Interrupt Link [LFWR] enabled at IRQ 21
ACPI-0201: *** Error: Return object type is incorrect
[\_SB_.LATA._CRS] (Node f7f95f1c), AE_TYPE
ACPI: Unable to set IRQ for PCI Interrupt Link [LATA] (likely buggy ACPI
BIOS).
Try pci=noacpi or acpi=off
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
00:01:00[A] -> 1-18 -> IRQ 18 level high
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 16
00:01:00[B] -> 1-16 -> IRQ 16 level high
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 19
00:02:06[D] -> 1-19 -> IRQ 19 level high
number of MP IRQ sources: 16.
number of IO-APIC #1 registers: 24.
testing the IO APIC.......................
IO APIC #1......
.... register #00: 01000000
....... : physical APIC id: 01
....... : Delivery Type: 0
....... : LTS : 0
.... register #01: 00170011
....... : max redirection entries: 0017
....... : PRQ implemented: 0
....... : IO APIC version: 0011
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 001 01 0 0 0 0 0 1 1 31
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 41
03 001 01 0 0 0 0 0 1 1 49
04 001 01 0 0 0 0 0 1 1 51
05 001 01 0 0 0 0 0 1 1 59
06 001 01 0 0 0 0 0 1 1 61
07 001 01 0 0 0 0 0 1 1 69
08 001 01 0 0 0 0 0 1 1 71
09 001 01 0 1 0 0 0 1 1 79
0a 001 01 0 0 0 0 0 1 1 81
0b 001 01 0 0 0 0 0 1 1 89
0c 001 01 0 0 0 0 0 1 1 91
0d 001 01 0 0 0 0 0 1 1 99
0e 001 01 0 0 0 0 0 1 1 A1
0f 001 01 0 0 0 0 0 1 1 A9
10 001 01 1 1 0 0 0 1 1 D9
11 000 00 1 0 0 0 0 0 0 00
12 001 01 1 1 0 0 0 1 1 D1
13 001 01 1 1 0 0 0 1 1 E1
14 001 01 1 1 0 0 0 1 1 C9
15 001 01 1 1 0 0 0 1 1 C1
16 001 01 1 1 0 0 0 1 1 B9
17 001 01 1 1 0 0 0 1 1 B1
IRQ to pin mappings:
IRQ0 -> 0:0
IRQ1 -> 0:1
IRQ2 -> 0:2
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ20 -> 0:20
IRQ21 -> 0:21
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
PCI: Using ACPI for IRQ routing
highmem bounce pool size: 64 pages
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 48 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
NET: Registered protocol family 8
NET: Registered protocol family 20
ACPI: (supports S0 S1 S3 S4 S5)
RAMDISK: cramfs filesystem found at block 0
RAMDISK: Loading 4572 blocks [1 disk] into ram disk... done.
VFS: Mounted root (cramfs filesystem) readonly.
Freeing unused kernel memory: 148k freed
NET: Registered protocol family 1
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
NFORCE2: IDE controller at PCI slot 0000:00:09.0
NFORCE2: chipset revision 162
NFORCE2: not 100% native mode: will probe irqs later
NFORCE2: BIOS didn't set cable bits correctly. Enabling workaround.
NFORCE2: 0000:00:09.0 (rev a2) UDMA133 controller
ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio
hda: ST3120022A, ATA DISK drive
hdb: ST340014A, ATA DISK drive
Using anticipatory io scheduler
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: ASUS CRW-5224A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63,
UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 < p5 >
hdb: max request size: 1024KiB
hdb: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=16383/255/63,
UDMA(100)
/dev/ide/host0/bus0/target1/lun0: p1 p2 < p5 p6 >
SGI XFS with ACLs, security attributes, realtime, large block numbers, no
debug enabled
SGI XFS Quota Management subsystem
NTFS driver 2.1.8 [Flags: R/O MODULE].
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
Adding 497960k swap on /dev/hdb5. Priority:-1 extents:1
EXT3 FS on hdb1, internal journal
Real Time Clock Driver v1.12
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3
[PCSPP,TRISTATE,COMPAT,ECP,DMA]
parport0: Printer, Canon BJC-2000
mice: PS/2 mouse device common for all mice
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
hdc: ATAPI 52X CD-ROM CD-R/RW CD-MRW drive, 2048kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.20
subfs 0.9
Linux video capture interface: v1.00
bttv: driver version 0.9.14 loaded
bttv: using 8 buffers with 2080k (520 pages) each for capture
bttv: Bt8xx card found (0).
bttv0: Bt878 (rev 2) at 0000:02:08.0, irq: 18, latency: 64, mmio:
0xec800000
bttv0: detected: FlyVideo 98 (LR50)/ Chronos Video Shuttle II [card=35],
PCI subsystem ID is 1851:1850
bttv0: using: Lifeview FlyVideo 98 LR50 / Chronos Video Shuttle II
[card=35,autodetected]
bttv0: gpio: en=00000000, out=00000000 in=0084ff00 [init]
bttv0: FlyVideo Radio=no RemoteControl=yes Tuner=5 gpio=0x84ff00
bttv0: FlyVideo LR90=no tda9821/tda9820=no capture_only=no
bttv0: using tuner=5
bttv0: i2c: checking for MSP34xx @ 0x80... not found
bttv0: i2c: checking for TDA9875 @ 0xb0... not found
bttv0: i2c: checking for TDA7432 @ 0x8a... not found
tuner: chip found at addr 0xc2 i2c-bus bt878 #0 [sw]
tuner: type set to 5 (Philips PAL_BG (FI1216 and compatibles)) by bt878 #0
[sw]
bttv0: registered device video0
bttv0: registered device vbi0
bttv0: PLL: 28636363 => 35468950 .. ok
Capability LSM initialized
kjournald starting. Commit interval 5 seconds
EXT3 FS on hdb6, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
NTFS volume version 3.1.
forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.25.
PCI: Setting latency timer of device 0000:00:04.0 to 64
eth0: forcedeth.c: subsystem: 01043:80a7 bound to 0000:00:04.0
dmfe: Davicom DM9xxx net driver, version 1.36.4 (2002-01-17)
eth1: Davicom DM9102 at pci0000:02:07.0, 00:08:a1:4c:28:09, irq 19.
usbcore: registered new driver usbfs
usbcore: registered new driver hub
ehci_hcd 0000:00:02.2: nVidia Corporation nForce2 USB Controller
PCI: Setting latency timer of device 0000:00:02.2 to 64
ehci_hcd 0000:00:02.2: irq 22, pci mem f8a90000
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
PCI: cache line size of 64 is not supported by device 0000:00:02.2
ehci_hcd 0000:00:02.2: USB 2.0 enabled, EHCI 1.00, driver 2003-Dec-29
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
NET: Registered protocol family 17
IA-32 Microcode Update Driver: v1.13 <tigran@veritas.com>
lp0: using parport0 (interrupt-driven).
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (8190 buckets, 65520 max) - 296 bytes per
conntrack
vmmon: module license 'unspecified' taints kernel.
/dev/vmmon: Module vmmon: registered with major=10 minor=165
/dev/vmmon: Module vmmon: initialized
vmnet: module license 'unspecified' taints kernel.
/dev/vmnet: open called by PID 1397 (vmnet-bridge)
/dev/vmnet: hub 0 does not exist, allocating memory.
/dev/vmnet: port on hub 0 successfully opened
bridge-eth0: enabling the bridge
bridge-eth0: up
bridge-eth0: already up
bridge-eth0: attached
/dev/vmnet: open called by PID 1409 (vmnet-natd)
/dev/vmnet: hub 8 does not exist, allocating memory.
/dev/vmnet: port on hub 8 successfully opened
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
/dev/vmnet: open called by PID 1484 (vmnet-netifup)
/dev/vmnet: hub 1 does not exist, allocating memory.
/dev/vmnet: port on hub 1 successfully opened
/dev/vmnet: open called by PID 1483 (vmnet-netifup)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1506 (vmnet-dhcpd)
/dev/vmnet: port on hub 8 successfully opened
/dev/vmnet: open called by PID 1496 (vmnet-dhcpd)
/dev/vmnet: port on hub 1 successfully opened
NET: Registered protocol family 10
Disabled Privacy Extensions on device c02e8f00(lo)
IPv6 over IPv4 tunneling driver
vmnet8: no IPv6 routers present
eth0: no IPv6 routers present
vmnet1: no IPv6 routers present
eth1: no IPv6 routers present
blk: queue c1b00600, I/O limit 4095Mb (mask 0xffffffff)
/dev/vmnet: open called by PID 1752 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
/dev/vmmon: fast clock rate 0 -> 19
/dev/vmmon: fast clock rate 19 -> 20
/dev/vmmon: fast clock rate 20 -> 84
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
ISO 9660 Extensions: RRIP_1991A
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
NTFS-fs error (device hda1): ntfs_ucstonls(): Unicode name contains
characters that cannot be converted to character set cp437.
/dev/vmmon: fast clock rate 84 -> 20
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: fast clock rate 20 -> 0
vmmon: Had to deallocate locked 65522 pages from vm driver ee1efe00
vmmon: Had to deallocate AWE 2285 pages from vm driver ee1efe00
/dev/vmnet: open called by PID 1945 (vmware-vmx)
bridge-eth0: set IFF_PROMISC
eth0: Promiscuous mode enabled.
/dev/vmnet: port on hub 0 successfully opened
/dev/vmmon: fast clock rate 0 -> 19
/dev/vmmon: fast clock rate 19 -> 20
/dev/vmmon: fast clock rate 20 -> 84
/dev/vmmon: fast clock rate 84 -> 20
bridge-eth0: clear IFF_PROMISC
/dev/vmmon: fast clock rate 20 -> 0
vmmon: Had to deallocate locked 65057 pages from vm driver ee1f7e00
vmmon: Had to deallocate AWE 2486 pages from vm driver ee1f7e00
parport0: BUSY timeout (1) in compat_write_block_pio
Attachment:
XFree86.0.log.gz
Description: GNU Zip compressed data