Re: eth1 & fsck

[Paweł Kordys <nieuwierzyszwwudu@gmail.com>]

Wojciech Ziniewicz napisał(a):
> 2006/10/1, Paweł Kordys <nieuwierzyszwwudu@gmail.com>:
> > Witam,
> >
> > Ma ktoś może pomysł dlaczego po
> > "shutdown -hF now" nie podnosi się interfesj eth1, po
> > "shutdown -h now" wszystko jest ok.
> >
> > Jakieś sugestie gdzie w ogóle szukac???
>
> jakies acpid apmd itd ? ..
a cóż to może mieć wspólnego? Cóż załączam diff pomiędzy dmesg'ami w obu 
przypadkach może komuś uda się coś z tego wywróżyc :-)

pozdr,

45c45
< Detected 1464.676 MHz processor.
---
> Detected 1464.611 MHz processor.
52c52
< Calibrating delay using timer specific routine.. 2932.51 BogoMIPS 
(lpj=5865025)
---
> Calibrating delay using timer specific routine.. 2932.51 BogoMIPS 
(lpj=5865020)
151c151
< audit(1160484717.536:1): initialized
---
> audit(1160484999.324:1): initialized
180c180
< ACPI: Thermal Zone [THRM] (37 C)
---
> ACPI: Thermal Zone [THRM] (38 C)
256,259d255
< irda_init()
< NET: Registered protocol family 23
< input: PC Speaker as /class/input/input1
< 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
260a257,259
> 00:0a: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
> input: PC Speaker as /class/input/input1
> eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
261a261,262
> Floppy drive(s): fd0 is 1.44M
> FDC 0 is a post-1991 82077
265,266d265
< Floppy drive(s): fd0 is 1.44M
< FDC 0 is a post-1991 82077
269,274d267
< i2c_adapter i2c-0: nForce2 SMBus adapter at 0x5000
< i2c_adapter i2c-1: nForce2 SMBus adapter at 0x5100
< eth1394: eth0: IEEE-1394 IPv4 over 1394 Ethernet (fw-host0)
< input: ImPS/2 Generic Wheel Mouse as /class/input/input2
< pci_hotplug: PCI Hot Plug PCI Core version: 0.5
< shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
291,292c284,285
< tuner 2-0061: chip found @ 0xc2 (bt878 #0 [sw])
< tuner 2-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
---
> tuner 0-0061: chip found @ 0xc2 (bt878 #0 [sw])
> tuner 0-0061: type set to 5 (Philips PAL_BG (FI1216 and compatibles))
295c288,289
< bttv0: PLL: 28636363 => 35468950 ..<6>ts: Compaq touchscreen protocol 
output
---
> bttv0: PLL: 28636363 => 35468950 ..<6>i2c_adapter i2c-1: nForce2 
SMBus adapter at 0x5000
> i2c_adapter i2c-2: nForce2 SMBus adapter at 0x5100
297,300c291,294
< mice: PS/2 mouse device common for all mice
< ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
< ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, 
high) -> IRQ 193
< PCI: Setting latency timer of device 0000:00:06.0 to 64
---
> input: ImPS/2 Generic Wheel Mouse as /class/input/input2
> irda_init()
> NET: Registered protocol family 23
> pci_hotplug: PCI Hot Plug PCI Core version: 0.5
302,303d295
< intel8x0_measure_ac97_clock: measured 52677 usecs
< intel8x0: clocking to 47409
309a302,309
> shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
> ts: Compaq touchscreen protocol output
> mice: PS/2 mouse device common for all mice
> ACPI: PCI Interrupt Link [APCJ] enabled at IRQ 20
> ACPI: PCI Interrupt 0000:00:06.0[A] -> Link [APCJ] -> GSI 20 (level, 
high) -> IRQ 193
> PCI: Setting latency timer of device 0000:00:06.0 to 64
> intel8x0_measure_ac97_clock: measured 52658 usecs
> intel8x0: clocking to 48000
318,319d317
< ACPI: Power Button (FF) [PWRF]
< ACPI: Power Button (CM) [PWRB]
322a321,322
> ACPI: Power Button (FF) [PWRF]
> ACPI: Power Button (CM) [PWRB]
329a330
> eth1: no IPv6 routers present