Re: routing - dlaczego nie dziala?
Witaj voder,
W Twoim liście datowanym 12 lipca 2001 (14:36:55) można przeczytać:
vap> On Thu, 12 Jul 2001, seeb27 wrote:
>> Witaj Polska Lista Debiana!
>> mam 64 ip i chcialem je podzielic na dwie czesci (podsieci)
>> eth0 ma ip z koncowka 97 eth1 ma 66, glowny router ma 65 i podzielilem to tak :
--- ciach ---
Witaj voder,
W Twoim liście datowanym 12 lipca 2001 (14:36:55) można przeczytać:
vap> On Thu, 12 Jul 2001, seeb27 wrote:
>> Witaj Polska Lista Debiana!
>> mam 64 ip i chcialem je podzielic na dwie czesci (podsieci)
>> eth0 ma ip z koncowka 97 eth1 ma 66, glowny router ma 65 i podzielilem to tak :
--- ciach ---
seebnet:/# cat /proc/sys/net/ipv4/ip_forward
1
seebnet:/# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
212.244.25.64 0.0.0.0 255.255.255.224 U 0 0 0 eth1
212.244.25.96 0.0.0.0 255.255.255.224 U 0 0 0 eth0
0.0.0.0 212.244.25.65 0.0.0.0 UG 0 0 0 eth1
seebnet:/# ifconfig -a
brg0 Link encap:Ethernet HWaddr FE:FD:0E:00:60:D6
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
eth0 Link encap:Ethernet HWaddr 00:02:44:31:33:5C
inet addr:212.244.25.97 Bcast:212.244.25.127 Mask:255.255.255.224
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:497 errors:0 dropped:0 overruns:0 frame:0
TX packets:39 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:100
RX bytes:29868 (29.1 Kb) TX bytes:3008 (2.9 Kb)
Interrupt:3 Base address:0xde00
eth1 Link encap:Ethernet HWaddr 00:D0:09:2B:73:1F
inet addr:212.244.25.66 Bcast:212.244.25.95 Mask:255.255.255.224
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:6757 errors:0 dropped:0 overruns:0 frame:0
TX packets:4317 errors:0 dropped:0 overruns:0 carrier:0
collisions:480 txqueuelen:100
RX bytes:608656 (594.3 Kb) TX bytes:497537 (485.8 Kb)
Interrupt:10 Base address:0xdc00
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:3924 Metric:1
RX packets:720 errors:0 dropped:0 overruns:0 frame:0
TX packets:720 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:88670 (86.5 Kb) TX bytes:88670 (86.5 Kb)
seebnet:/#
to nadal nie dziala :(
po glebszym przemysleniu zdaje sie ze cos tu nie gra
seebnet:/# route -n
Kernel IP routing table
Destination Gateway Genmask Flags Metric Ref Use Iface
212.244.25.64 0.0.0.0 255.255.255.224 U 0 0 0 eth1
212.244.25.96 0.0.0.0 255.255.255.224 U 0 0 0 eth0
czy przypadkiem dla sieci 212.244.25.64 gatewayem jest 212.244.25.97 a
dla jest 212.244.25.66 a dopiero dla wszytkich innych
(nie pasujacych do tego) 212.244.25.65?
mialem w redhata i przyjmowal formulke :
route add -net 212.244.25.96 gw 212.244.25.66 netmask 255.255.255.224 ethX
(X - dowolny dzialajac interfejs) a jakos debian tego nie lubi :(
w ten sposob rutowalem prywatna klase c (192.168.0.0) podzielona na
pol i w kompie mialem 3 karty sieciowe (eth0, [eth1,eth2-prywatna])
co z tym fantem zrobic ?
--
Pozdrowienia,
seeb27 mailto:seeb27@interkam.pl
Reply to: