[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Re: Epson Scanner unter Bullseye geht nicht mehr



Hallo,

was ich nun auch noch versucht habe:

# systemctl status saned.socket
● saned.socket - saned incoming socket
    Loaded: loaded (/lib/systemd/system/saned.socket; disabled; vendor preset: enabled)
    Active: inactive (dead)
    Listen: [::]:6566 (Stream)
  Accepted: 0; Connected: 0;



Am 08.02.22 um 14:40 schrieb Siegfrid Brandstätter:

Hallo,

bis zum Update auf Bullseye hatte ich mit meinem Epson XP 3015 keine Probleme mit dem scannen.

Aber nun wird von Xsane kein Scanner gefunden.


# sudo sane-find-scanner  

 # sane-find-scanner will now attempt to detect your scanner. If the
 # result is different from what you expected, first make sure your
 # scanner is powered up and properly connected to your computer.

 # No SCSI scanners found. If you expected something different, make sure that
 # you have loaded a kernel SCSI driver for your SCSI adapter.

could not fetch string descriptor: Pipe error
could not fetch string descriptor: Pipe error
found USB scanner (vendor=0x04b8, product=0x1136) at libusb:005:002
could not fetch string descriptor: Pipe error
found USB scanner (vendor=0x0b05 [AsusTek Computer Inc.], product=0x18f3 [AURA LED Controller]) at libusb:003:002
could not fetch string descriptor: Pipe error
could not fetch string descriptor: Pipe error
 # Your USB scanner was (probably) detected. It may or may not be supported by
 # SANE. Try scanimage -L and read the backend's manpage.

 # Not checking for parallel port scanners.

 # Most Scanners connected to the parallel port or other proprietary ports
 # can't be detected by this program.

Mit dmesg sehe ich aber:

--- [   11.312128] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[   14.290568] igb 0000:03:00.0 enp3s0: igb: enp3s0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[   14.614146] IPv6: ADDRCONF(NETDEV_CHANGE): enp3s0: link becomes ready
[   18.076823] igb 0000:03:00.0 enp3s0: igb: enp3s0 NIC Link is Up 1000 Mbps Full Duplex, Flow Control: RX/TX
[ 1193.144386] usb 5-3: USB disconnect, device number 2
[ 1193.436708] usb 5-3: new high-speed USB device number 4 using xhci_hcd
[ 1193.772835] usb 5-3: device descriptor read/64, error -71
[ 1194.040110] usb 5-3: New USB device found, idVendor=04b8, idProduct=1136, bcdDevice= 1.00
[ 1194.040113] usb 5-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1194.040115] usb 5-3: Product: XP-3100 Series
[ 1194.040116] usb 5-3: Manufacturer: EPSON
[ 1194.040117] usb 5-3: SerialNumber: 5836424D3032343171
[ 1194.104803] usblp 5-3:1.1: usblp1: USB Bidirectional printer dev 4 if 1 alt 0 proto 2 vid 0x04B8 pid 0x1136
[ 1194.129736] usblp1: removed
[ 1194.788611] usb 5-3: USB disconnect, device number 4
[ 1195.104742] usb 5-3: new high-speed USB device number 5 using xhci_hcd
[ 1195.292112] usb 5-3: New USB device found, idVendor=04b8, idProduct=1136, bcdDevice= 1.00
[ 1195.292116] usb 5-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1195.292118] usb 5-3: Product: XP-3100 Series
[ 1195.292118] usb 5-3: Manufacturer: EPSON
[ 1195.292119] usb 5-3: SerialNumber: 5836424D3032343171
[ 1195.352791] usblp 5-3:1.1: usblp1: USB Bidirectional printer dev 5 if 1 alt 0 proto 2 vid 0x04B8 pid 0x1136
[ 1195.378034] usblp1: removed
[ 1195.760739] usb 5-3: USB disconnect, device number 5
[ 1198.724714] usb 5-3: new high-speed USB device number 6 using xhci_hcd
[ 1198.884364] usb 5-3: New USB device found, idVendor=04b8, idProduct=1136, bcdDevice= 1.00
[ 1198.884368] usb 5-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 1198.884369] usb 5-3: Product: XP-3100 Series
[ 1198.884370] usb 5-3: Manufacturer: EPSON
[ 1198.884371] usb 5-3: SerialNumber: 5836424D3032343171
[ 1198.936536] usblp 5-3:1.1: usblp1: USB Bidirectional printer dev 6 if 1 alt 0 proto 2 vid 0x04B8 pid 0x1136
[ 1198.959569] usblp1: removed

Die Installation ist auch vorhanden wie in dieser Anleitung beschrieben

https://wiki.ubuntuusers.de/Scanner/Epson/

Der Drucker/Scanner sagt mir wenn ich es von diesem aus versuche: Kommunikationsfehler, Verbindung überprüfen. Das USB Kabel hab ich schon an alle Möglichkeiten angesteckt mit selben Misserfolg.

An was kann es liegen?


-- 
Beste Grüße
Sigi


-- 
Beste Grüße
Sigi

Reply to: