Re: Externe-USB Festplatte Fehler suche
Hallo Andreas,
Am 21.12.20 um 20:00 schrieb Andreas Weber:
manche Toshiba Platten "-d usbsunplus" oder "-d sat"
Danke! Mit -d sat hat es geklappt.
# smartctl -a -s on -d sat /dev/sdd
Copyright (C) 2002-17, Bruce Allen, Christian Franke,
www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: TOSHIBA MQ04UBD200
Serial Number: X8SFT8TKT
LU WWN Device Id: 0 000000 000000000
Firmware Version: JT000U
User Capacity: 2.000.398.934.016 bytes [2,00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Rotation Rate: 5400 rpm
Form Factor: 2.5 inches
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ACS-3 T13/2161-D revision 5
SATA Version is: SATA 3.3, 3.0 Gb/s (current: 3.0 Gb/s)
Local Time is: Mon Dec 21 20:34:00 2020 WET
SMART support is: Available - device has SMART capability.
SMART support is: Disabled
=== START OF ENABLE/DISABLE COMMANDS SECTION ===
SMART Enabled.
=== START OF READ SMART DATA SECTION ===
SMART Status not supported: Incomplete response, ATA output registers
missing
SMART overall-health self-assessment test result: PASSED
Warning: This result is based on an Attribute check.
General SMART Values:
Offline data collection status: (0x00) Offline data collection activity
was never started.
Auto Offline Data Collection:
Disabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test
has ever
been run.
Total time to complete Offline
data collection: ( 120) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection
on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 352) minutes.
SCT capabilities: (0x003d) SCT Status supported.
SCT Error Recovery Control
supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000b 100 100 050 Pre-fail
Always - 0
2 Throughput_Performance 0x0005 100 100 050 Pre-fail
Offline - 0
3 Spin_Up_Time 0x0027 100 100 001 Pre-fail
Always - 2410
4 Start_Stop_Count 0x0032 100 100 000 Old_age
Always - 2120
5 Reallocated_Sector_Ct 0x0033 100 100 050 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000b 100 100 050 Pre-fail
Always - 0
8 Seek_Time_Performance 0x0005 100 100 050 Pre-fail
Offline - 0
9 Power_On_Hours 0x0032 098 098 000 Old_age
Always - 814
10 Spin_Retry_Count 0x0033 142 100 030 Pre-fail
Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age
Always - 468
191 G-Sense_Error_Rate 0x0032 100 100 000 Old_age
Always - 0
192 Power-Off_Retract_Count 0x0032 100 100 000 Old_age
Always - 158
193 Load_Cycle_Count 0x0032 099 099 000 Old_age
Always - 14065
194 Temperature_Celsius 0x0022 100 100 000 Old_age
Always - 24 (Min/Max 17/57)
196 Reallocated_Event_Count 0x0032 100 100 000 Old_age
Always - 0
197 Current_Pending_Sector 0x0032 100 100 000 Old_age
Always - 0
198 Offline_Uncorrectable 0x0030 100 100 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age
Always - 0
220 Disk_Shift 0x0002 100 100 000 Old_age
Always - 26
222 Loaded_Hours 0x0032 100 100 000 Old_age
Always - 350
223 Load_Retry_Count 0x0032 100 100 000 Old_age
Always - 0
224 Load_Friction 0x0022 100 100 000 Old_age
Always - 0
226 Load-in_Time 0x0026 100 100 000 Old_age
Always - 164
240 Head_Flying_Hours 0x0001 100 100 001 Pre-fail
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
#######################################################
# smartctl -d sat --log error /dev/sdd
smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-13-amd64] (local build)
Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF READ SMART DATA SECTION ===
SMART Error Log Version: 1
No Errors Logged
Bin mir nun aber nicht sicher ob alles OK ist.
--
Beste Grüße
Sigi
Reply to: