Re: NACHTRAG: Re: Warnung: Automatisierte VirtualBox-Installaion zerschießt u.U. Systemstartmechanismus(!)
schrieb Jochen Schulz:
schrieb Sascha Reißner:
Trotzdem würde ich, wie es Jochen bereits schrieb, nach vertächtigen
Einträgen in den Logfiles ausschau halten und mit den SMART-Tools die
Platte mal gründlich prüfen.
Am besten gleich smartd einrichten, damit du bescheit bekommst, wenn die
Platte vertächtig wird.
Die bekommst Du als Debian-Paket mit dem Namen smartmontools. Nach der
Installation einfach mal 'smartctl -a /dev/sdX' (passendes Device
angeben) aufrufen und den Output hier posten. Wenn möglich, ohne die
Zeilen der Ausgabe umzubrechen. Wenn Du Deinem Editor nicht trauen
kannst, als Anhang.
Hier nun die Ausgabe von 'smartctl -a /dev/sda':
smartctl -a /dev/sda
smartctl 5.40 2010-07-12 r3124 [i686-pc-linux-gnu] (local build)
Copyright (C) 2002-10 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Model Family: Western Digital Caviar family
Device Model: WDC WD400BB-60JKC0
Serial Number: WD-WMAME2277544
Firmware Version: 05.01C05
User Capacity: 40.020.664.320 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Fri Mar 4 18:02:27 2011 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine
completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (1260) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 23) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x003f) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE
UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 200 200 051 Pre-fail
Always - 0
3 Spin_Up_Time 0x0003 167 166 021 Pre-fail
Always - 2650
4 Start_Stop_Count 0x0032 099 099 000 Old_age
Always - 1509
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail
Always - 0
7 Seek_Error_Rate 0x000f 200 200 051 Pre-fail
Always - 0
9 Power_On_Hours 0x0032 097 097 000 Old_age
Always - 2901
10 Spin_Retry_Count 0x0013 100 100 051 Pre-fail
Always - 0
11 Calibration_Retry_Count 0x0012 100 100 051 Old_age
Always - 0
12 Power_Cycle_Count 0x0032 099 099 000 Old_age
Always - 1509
194 Temperature_Celsius 0x0022 110 094 000 Old_age Always
- 33
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always
- 0
197 Current_Pending_Sector 0x0012 200 200 000 Old_age Always
- 0
198 Offline_Uncorrectable 0x0010 200 200 000 Old_age
Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 200 000 Old_age Always
- 0
200 Multi_Zone_Error_Rate 0x0009 200 200 051 Pre-fail
Offline - 0
SMART Error Log Version: 1
No Errors Logged
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
-> ist das für jmd. von Euch bereits aussagekräftig?
-> wie richte ich smartd auf /dev/sda ein? (bzw. was ist das für ein
mächtiges Tool?)
DANKE für Eure Unterstützung!
Gruß
Andreas
--
Andreas Gottwald
a.go@vr-web.de
Reply to: