Re: Einfrieren-Datenverlust und anderes
Hallo Michael,
Am Mittwoch, 1. September 2010 schrieb [ML] Michael Windelen:
> schrieb Siegfrid Brandstätter am 31.08.2010 22:27:
> > Am Dienstag, 31. August 2010 schrieb Martin Steigerwald:
> >> Am Dienstag 31 August 2010 schrieb Siegfrid Brandstätter:
> >>> Hallo Martin,
> >>>
> >>> Am Dienstag, 31. August 2010 18:15 schrieb Martin Steigerwald:
> >>>> zgrep hda /var/log/syslog* | grep -vi reiserfs | less
> >>>
> >>> wäre das mit etch auch möglich oder muß ich das mit lenny machen?
> >>
> >> Natürlich mit dem System, mit dem der Fehler auftritt! ;).
> >
> > OK:
> > # zgrep hda /var/log/syslog* | grep -vi reiserfs | less
> >
> > var/log/syslog:Aug 31 10:55:29 dlx kernel: [ 2045.460138]
> > end_request: I/O error, dev hda, sector 57675101
> > /var/log/syslog:Aug 31 10:55:29 dlx kernel: [ 2045.460170]
> > end_request: I/O error, dev hda, sector 57675109
> > /var/log/syslog:Aug 31 10:57:30 dlx kernel: [ 2165.808089]
> > end_request: I/O error, dev hda, sector 57673421
>
> [..]
>
> Hallo,
>
> das sieht nach kaputter Festplatte aus wenn ich mich nicht Irre...
>
> Was sagt denn ein smartctl -H /dev/hda?
>
> Mach mal bitte danach ein smartctl -t long /dev/hda
> (das sagt der Platte dass sie sich einem Selbsttest unterziehen soll)
>
> und dann nach der Zeit die die Ausgabe des Befehls Angibt ein:
>
> smartctl -a /dev/hda und poste das mal (vielleicht als angehängte
> Textdatei damit der die Zeilen nicht nach 72 Zeichen umbricht, das
> ist dabei Ausgabe beim lesen ekelig).
> (z.B.kannst du die Textdatei erstellen durch ein smartctl -a /dev/hda
> > DATEIPFAD/smartctl.txt) Dateipfad ist zu ersetzen ;)
>
> falls der Befehl unbekannt ist hilft eine Installation des Paketes
> smartmontools.
>
Schaut so aus als ob das nur sehr alte Fehler auf der Platte sind, oder?
Denke es war doch wieder mal dieses alte dicke Kabel, leider bekomme ich
hier keine andern, war schon froh als ich noch den letzten Rest
erhielt. Aber irgendwann ist dann mal ein neuer PC auch fällig, bis
dahin sollte es halt noch so laufen. Werde mir aber nun noch eine
Externe Platte zulegen und damit nochmals extra sichern.
--
Einen Schönen Gruß,
Sigi
smartctl version 5.38 [i686-pc-linux-gnu] Copyright (C) 2002-8 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Model Family: Seagate Barracuda 7200.7 and 7200.7 Plus family
Device Model: ST340014A
Serial Number: 5JX0D218
Firmware Version: 3.04
User Capacity: 40.020.664.320 bytes
Device is: In smartctl database [for details use: -P show]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Wed Sep 1 12:48:29 2010 WEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: ( 430) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 31) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x000f 059 056 006 Pre-fail Always - 92869850
3 Spin_Up_Time 0x0003 099 098 000 Pre-fail Always - 0
4 Start_Stop_Count 0x0032 100 100 020 Old_age Always - 30
5 Reallocated_Sector_Ct 0x0033 100 100 036 Pre-fail Always - 0
7 Seek_Error_Rate 0x000f 079 060 030 Pre-fail Always - 91763442
9 Power_On_Hours 0x0032 081 081 000 Old_age Always - 17498
10 Spin_Retry_Count 0x0013 100 100 097 Pre-fail Always - 0
12 Power_Cycle_Count 0x0032 093 093 020 Old_age Always - 8167
194 Temperature_Celsius 0x0022 039 054 000 Old_age Always - 39
195 Hardware_ECC_Recovered 0x001a 059 056 000 Old_age Always - 92869850
197 Current_Pending_Sector 0x0012 100 100 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0010 100 100 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x003e 200 189 000 Old_age Always - 961
200 Multi_Zone_Error_Rate 0x0000 100 253 000 Old_age Offline - 0
202 TA_Increase_Count 0x0032 100 253 000 Old_age Always - 0
SMART Error Log Version: 1
ATA Error Count: 502 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 502 occurred at disk power-on lifetime: 16364 hours (681 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 d4 40 75 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x007540d4 = 7684308
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 cd 40 75 e0 00 05:32:26.160 READ DMA EXT
25 00 10 b5 9f 70 e0 00 05:31:55.320 READ DMA EXT
25 00 08 9d 9f 70 e0 00 05:31:55.320 READ DMA EXT
25 00 08 85 9f 70 e0 00 05:31:55.319 READ DMA EXT
b0 d0 01 00 4f c2 e0 00 05:31:45.756 SMART READ DATA
Error 501 occurred at disk power-on lifetime: 16364 hours (681 days + 20 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 04 bd 77 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x0077bd04 = 7847172
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 c5 bc 77 e0 00 05:26:51.458 READ DMA EXT
b0 d0 01 00 4f c2 e0 00 05:26:51.457 SMART READ DATA
b0 d8 00 00 4f c2 e0 00 05:26:51.437 SMART ENABLE OPERATIONS
e5 00 00 00 00 08 e0 00 05:26:18.879 CHECK POWER MODE
25 00 08 2d fe 78 e0 00 05:26:18.878 READ DMA EXT
Error 500 occurred at disk power-on lifetime: 16040 hours (668 days + 8 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 84 1b 70 e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00701b84 = 7347076
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 40 45 1b 70 e0 00 03:55:18.236 READ DMA EXT
25 00 40 85 1c 70 e0 00 03:57:29.989 READ DMA EXT
25 00 10 4d a3 75 e0 00 03:57:26.728 READ DMA EXT
25 00 08 3d a3 75 e0 00 03:57:06.138 READ DMA EXT
b0 d0 01 00 4f c2 e0 00 03:57:06.121 SMART READ DATA
Error 499 occurred at disk power-on lifetime: 11122 hours (463 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 d7 2e ff e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00ff2ed7 = 16723671
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 d0 2e ff e0 00 00:23:01.106 READ DMA EXT
25 00 08 d0 2e ff e0 00 00:23:00.421 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:22:59.721 RECALIBRATE [OBS-4]
25 00 08 d0 2e ff e0 00 00:22:59.720 READ DMA EXT
25 00 08 d0 2e ff e0 00 00:22:59.716 READ DMA EXT
Error 498 occurred at disk power-on lifetime: 11122 hours (463 days + 10 hours)
When the command that caused the error occurred, the device was active or idle.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 01 d7 2e ff e0 Error: ICRC, ABRT 1 sectors at LBA = 0x00ff2ed7 = 16723671
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name
-- -- -- -- -- -- -- -- ---------------- --------------------
25 00 08 d0 2e ff e0 00 00:23:01.106 READ DMA EXT
10 00 3f 00 00 00 e0 00 00:23:00.421 RECALIBRATE [OBS-4]
25 00 08 d0 2e ff e0 00 00:22:59.721 READ DMA EXT
25 00 08 d0 2e ff e0 00 00:22:59.720 READ DMA EXT
25 00 08 00 00 00 e0 00 00:22:59.716 READ DMA EXT
SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error
# 1 Extended offline Completed without error 00% 17497 -
# 2 Extended offline Completed without error 00% 13572 -
# 3 Extended offline Completed without error 00% 13570 -
# 4 Short offline Completed without error 00% 10890 -
# 5 Extended offline Completed without error 00% 3895 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Reply to: