raid 1 logical und physical drives sichtbar mit megaraid in Etch
Hallo zusammen
Ich habe soeben von Sarge auf Etch upgraded. Nun habe ich das Problem,
dass ich von meinem Hardware Raid Level 1 einerseits das logische
Laufwerk sehe und andererseits die physikalischen Festplatten ebenso
einen devicenamen erhalten, komischerweise im Normalfall nur eine und im
Extremfall 6 Stück, obschon ja effektiv nur zwei HD's an diesem
Kontroller vorhanden sind
(ähnliches Verhalten wie bei
https://bugs.launchpad.net/ubuntu/+source/linux-source-2.6.15/+bug/55138)
Da es nicht konstant immer gleich ist, rutscht meine externe
SCSI-Festplatte (am zweiten SCSI-Kontroller) zwischen sdc und sdh umher,
was nicht sehr praktisch ist.
Kernel ist 2.6.18-4-686.
Kennt irgendwer das Problem und hat eine Lösung dazu?
Danke und Gruss
Pascal
Output von dmesg:
SCSI subsystem initialized
ACPI: PCI Interrupt 0000:00:09.1[A] -> GSI 17 (level, low) -> IRQ 169
megaraid: found 0x8086:0x1960:bus 0:slot 9:func 1
scsi0:Found MegaRAID controller at 0xd8814000, IRQ:169
megaraid: [F :B ] detected 1 logical drives.
megaraid: channel[0] is raid.
scsi0 : LSI Logic MegaRAID F 254 commands 16 targs 4 chans 7 luns
scsi0: scanning scsi channel 0 for logical drives.
Vendor: MegaRAID Model: LD0 RAID1 8677R Rev: F
Type: Direct-Access ANSI SCSI revision: 02
scsi0: scanning scsi channel 4 [P0] for physical devices.
Vendor: HP Model: 9.10GB A 80-F309 Rev:
Type: Direct-Access ANSI SCSI revision: 02
ACPI: PCI Interrupt 0000:01:04.0[A] -> GSI 18 (level, low) -> IRQ 177
sym0: <895> rev 0x1 at pci 0000:01:04.0 irq 177
sym0: Symbios NVRAM, ID 7, Fast-40, SE, parity checking
sym0: open drain IRQ line driver, using on-chip SRAM
sym0: using LOAD/STORE-based firmware.
sym0: SCSI BUS has been reset.
sym0: SCSI BUS mode change from SE to SE.
scsi1 : sym-2.2.3
sym0: SCSI BUS has been reset.
Vendor: FUJITSU Model: MAP3367NP Rev: 0108
Type: Direct-Access ANSI SCSI revision: 03
target1:0:4: tagged command queuing enabled, command queue depth 16.
target1:0:4: Beginning Domain Validation
target1:0:4: asynchronous
target1:0:4: FAST-20 SCSI 20.0 MB/s ST (50 ns, offset 31)
target1:0:4: Domain Validation skipping write tests
target1:0:4: Ending Domain Validation
SCSI device sda: 17770496 512-byte hdwr sectors (9098 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: asking for cache data failed
sda: assuming drive cache: write through
SCSI device sda: 17770496 512-byte hdwr sectors (9098 MB)
sda: Write Protect is off
sda: Mode Sense: 00 00 00 00
sda: asking for cache data failed
sda: assuming drive cache: write through
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 >
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB)
sdb: Write Protect is off
sdb: Mode Sense: a7 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
SCSI device sdb: 17773524 512-byte hdwr sectors (9100 MB)
sdb: Write Protect is off
sdb: Mode Sense: a7 00 10 08
SCSI device sdb: drive cache: write through w/ FUA
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 sdb7 sdb8 >
sd 0:4:0:0: Attached scsi disk sdb
SCSI device sdc: 71775284 512-byte hdwr sectors (36749 MB)
sdc: Write Protect is off
sdc: Mode Sense: b3 00 00 08
SCSI device sdc: drive cache: write back
SCSI device sdc: 71775284 512-byte hdwr sectors (36749 MB)
sdc: Write Protect is off
sdc: Mode Sense: b3 00 00 08
SCSI device sdc: drive cache: write back
sdc: sdc1
sd 1:0:4:0: Attached scsi disk sdc
Reply to: