Naar aanleiding van de reactie van Geert Stappers:
Wat ik **zelf bedacht** heb, is deze ketting:
* Laptop
rene@dikke:~$ lsb_release -a
No LSB modules are available.
Distributor ID: Debian
Description: Debian GNU/Linux 9.13 (stretch)
Release: 9.13
Codename: stretch
rene@dikke:~$
Het fat16 kaartje is 1 GB groot, zogenaamd Hi-Speed. Deze wordt gebruikt voor een 3D-printer. De printer biedt niet de mogelijkheid de kaart eerst te ontkoppelen voordar deze verwijderd wordt.
Het 1-e exfat kaartje is een micr SD-kaartje van 64 GB, Sandisk ultra, in een adapterkaart.
Het 2-e exfat kaartje is een micr SD-kaartje van 128 GB, Sandisk ultra, in een adapterkaart.
De SD-kaartjes gaan in een kaartsleuf in de laptop. Ik denk daarom dat e.e.a. niet met USB te maken heeft, maar vergeef me mijn gebrek aan kennis.
* USB poort (Type ... , werkt goed met ... )
n.v.t.
* USB kabel, de originele die bij de camera hoort
n.v.t.
* USB connector, geen beschadigingen te zien
n.v.t.
* Camera, lastig te omschrijven, toch een poging
* Stroom van uit het stopcontact (niet op batterijen)
* Wakker (niet in een slaapstand over andere power save mode
* Display c.q. Menu van de camera toont beide SD-kaartjes
* De sleufen voor de SD-kaartje verschillen alleen van nummer
( geen aanwijzigingen als "Configuration" of "Mass storage"
of andere verschillen, gewoon SD1 en SD2)
alleen instelling voor welke soort bestanden op welke kaart gaan ( i.c. NEF en jpg ).
* Beide SD-kaartjes zijn van dezelfde Klasse
( https://en.wikipedia.org/wiki/SD_card#Class )
Ja.
> Na een reboot kan ik beide kaartjes *eenmalig* benaderen.
Dit was onnauwkeurig weergegeven: bedoeld was: Na een reboot kan ik alleen de eerst ingestoken exif-kaart benaderen.
>Wat is er **voor** en **na** met `lsusb` te zien?
Maakt geen verschil.
>Kernel diagnostic messages, commando `dmesg` wat laat die zien?
Zie onder.
>En als de Linux onderzocht is, onderzoek dan ook de camera kant.
Groeten
Geert Stappers
Leerde later pas dat Andriod devices verschillende USB-modes hebben.
--
Silence is hard to parse
...
- - - - - - - - - - - - - - - - - - - -
De output van dmesg met fat16 kaart ingestoken:
root@dikke:/home/rene# dmesg|tail
[90580.394296] wlp5s0: authenticated
[90580.401293] wlp5s0: associate with d4:7b:b0:3d:0e:75 (try 1/3)
[90580.402466] wlp5s0: RX AssocResp from d4:7b:b0:3d:0e:75 (capab=0x1011 status=0 aid=3)
[90580.407979] wlp5s0: associated
[90580.431870] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[90580.440070] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[91380.129830] mmc0: new SD card at address 0001
[91380.130080] mmcblk0: mmc0:0001 SD 974 MiB
[91380.131407] mmcblk0: p1
[91380.646465] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
root@dikke:/home/rene#
Na reboot:
root@dikke:/home/rene# dmesg|tail
[ 23.564903] IPv6: ADDRCONF(NETDEV_UP): wlp5s0: link is not ready
[ 30.862182] wlp5s0: authenticate with d4:7b:b0:3d:0e:75
[ 30.864520] wlp5s0: send auth to d4:7b:b0:3d:0e:75 (try 1/3)
[ 30.866580] wlp5s0: authenticated
[ 30.873895] wlp5s0: associate with d4:7b:b0:3d:0e:75 (try 1/3)
[ 30.877813] wlp5s0: RX AssocResp from d4:7b:b0:3d:0e:75 (capab=0x1011 status=0 aid=2)
[ 30.879310] wlp5s0: associated
[ 30.904825] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 30.972706] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 67.442245] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
root@dikke:/home/rene#
exfat kaart 1 ingestoken:
root@dikke:/home/rene# dmesg|tail
[ 30.873895] wlp5s0: associate with d4:7b:b0:3d:0e:75 (try 1/3)
[ 30.877813] wlp5s0: RX AssocResp from d4:7b:b0:3d:0e:75 (capab=0x1011 status=0 aid=2)
[ 30.879310] wlp5s0: associated
[ 30.904825] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 30.972706] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 67.442245] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 300.562258] mmc0: cannot verify signal voltage switch
[ 300.694220] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
root@dikke:/home/rene#
Na unmount:
root@dikke:/home/rene# dmesg|tail
[ 30.879310] wlp5s0: associated
[ 30.904825] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 30.972706] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 67.442245] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 300.562258] mmc0: cannot verify signal voltage switch
[ 300.694220] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
[ 595.051672] JFS: nTxBlock = 8192, nTxLock = 65536
[ 595.067213] SGI XFS with ACLs, security attributes, realtime, no debug enabled
root@dikke:/home/rene#
Na kaart verwijderd:
root@dikke:/home/rene# dmesg|tail
[ 30.904825] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 30.972706] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 67.442245] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
[ 300.562258] mmc0: cannot verify signal voltage switch
[ 300.694220] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
[ 595.051672] JFS: nTxBlock = 8192, nTxLock = 65536
[ 595.067213] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 701.582359] mmc0: card aaaa removed
root@dikke:/home/rene#
Zelfde exfat kaart opnieuw ingestoken:
root@dikke:/home/rene# dmesg|tail
[ 300.694220] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
[ 595.051672] JFS: nTxBlock = 8192, nTxLock = 65536
[ 595.067213] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 701.582359] mmc0: card aaaa removed
[ 4395.140556] mmc0: cannot verify signal voltage switch
[ 4395.273005] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 4395.273330] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 4395.275273] mmcblk0: p1
root@dikke:/home/rene#
Na kaart unmount:
root@dikke:/home/rene# dmesg|tail
[ 300.694220] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
[ 595.051672] JFS: nTxBlock = 8192, nTxLock = 65536
[ 595.067213] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 701.582359] mmc0: card aaaa removed
[ 4395.140556] mmc0: cannot verify signal voltage switch
[ 4395.273005] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 4395.273330] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 4395.275273] mmcblk0: p1
root@dikke:/home/rene#
Na kaart verwijderd:
root@dikke:/home/rene# dmesg|tail
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
[ 595.051672] JFS: nTxBlock = 8192, nTxLock = 65536
[ 595.067213] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 701.582359] mmc0: card aaaa removed
[ 4395.140556] mmc0: cannot verify signal voltage switch
[ 4395.273005] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 4395.273330] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 4395.275273] mmcblk0: p1
[ 4568.888117] mmc0: card aaaa removed
root@dikke:/home/rene#
2-e exfat kaart ingestoken:
root@dikke:/home/rene# dmesg|tail
[ 300.698010] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 300.699857] mmcblk0: p1
[ 595.051672] JFS: nTxBlock = 8192, nTxLock = 65536
[ 595.067213] SGI XFS with ACLs, security attributes, realtime, no debug enabled
[ 701.582359] mmc0: card aaaa removed
[ 4395.140556] mmc0: cannot verify signal voltage switch
[ 4395.273005] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 4395.273330] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 4395.275273] mmcblk0: p1
[ 4568.888117] mmc0: card aaaa removed
root@dikke:/home/rene#
wordt niets mee gedaan.
fat16 kaart ingestoken:
root@dikke:/home/rene# dmesg|tail
[ 701.582359] mmc0: card aaaa removed
[ 4395.140556] mmc0: cannot verify signal voltage switch
[ 4395.273005] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 4395.273330] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 4395.275273] mmcblk0: p1
[ 4568.888117] mmc0: card aaaa removed
[ 4683.319241] mmc0: new SD card at address 0001
[ 4683.319553] mmcblk0: mmc0:0001 SD 974 MiB
[ 4683.320615] mmcblk0: p1
[ 4683.797399] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
root@dikke:/home/rene#
fat16 kaart verwijderd:
root@dikke:/home/rene# dmesg|tail
[ 4395.140556] mmc0: cannot verify signal voltage switch
[ 4395.273005] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 4395.273330] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 4395.275273] mmcblk0: p1
[ 4568.888117] mmc0: card aaaa removed
[ 4683.319241] mmc0: new SD card at address 0001
[ 4683.319553] mmcblk0: mmc0:0001 SD 974 MiB
[ 4683.320615] mmcblk0: p1
[ 4683.797399] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4856.107726] mmc0: card 0001 removed
root@dikke:/home/rene#
1-e exfat kaart terug ingestoken:
root@dikke:/home/rene# dmesg|tail
[ 4683.319241] mmc0: new SD card at address 0001
[ 4683.319553] mmcblk0: mmc0:0001 SD 974 MiB
[ 4683.320615] mmcblk0: p1
[ 4683.797399] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4856.107726] mmc0: card 0001 removed
[ 4912.019329] mmc0: error -110 whilst initialising SD card
[ 5078.527469] mmc0: cannot verify signal voltage switch
[ 5078.659792] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 5078.660438] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 5078.662511] mmcblk0: p1
root@dikke:/home/rene#
Na verwijderen 1-e exfat kaart:
root@dikke:/home/rene# dmesg|tail
[ 4683.319553] mmcblk0: mmc0:0001 SD 974 MiB
[ 4683.320615] mmcblk0: p1
[ 4683.797399] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 4856.107726] mmc0: card 0001 removed
[ 4912.019329] mmc0: error -110 whilst initialising SD card
[ 5078.527469] mmc0: cannot verify signal voltage switch
[ 5078.659792] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 5078.660438] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 5078.662511] mmcblk0: p1
[ 5174.516502] mmc0: card aaaa removed
root@dikke:/home/rene#
Na slaapstand en opnieuw inloggen:
1-e exfat kaart:
root@dikke:/home/rene# dmesg|tail
[ 6054.338277] wlp5s0: authenticated
[ 6054.340932] wlp5s0: associate with d4:7b:b0:3d:0e:75 (try 1/3)
[ 6054.341952] wlp5s0: RX AssocResp from d4:7b:b0:3d:0e:75 (capab=0x1011 status=0 aid=2)
[ 6054.342448] wlp5s0: associated
[ 6054.384619] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 6054.392662] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 6500.504601] mmc0: cannot verify signal voltage switch
[ 6500.636217] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 6500.636433] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 6500.638585] mmcblk0: p1
root@dikke:/home/rene#
Na verwijdering:
root@dikke:/home/rene# dmesg|tail
[ 6054.340932] wlp5s0: associate with d4:7b:b0:3d:0e:75 (try 1/3)
[ 6054.341952] wlp5s0: RX AssocResp from d4:7b:b0:3d:0e:75 (capab=0x1011 status=0 aid=2)
[ 6054.342448] wlp5s0: associated
[ 6054.384619] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 6054.392662] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 6500.504601] mmc0: cannot verify signal voltage switch
[ 6500.636217] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 6500.636433] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 6500.638585] mmcblk0: p1
[ 6665.591687] mmc0: card aaaa removed
root@dikke:/home/rene#
Na reboot
root@dikke:/home/rene# dmesg|tail
[ 117.289793] IPv6: ADDRCONF(NETDEV_UP): wlp5s0: link is not ready
[ 117.395662] wlp5s0: authenticate with d4:7b:b0:3d:0e:75
[ 117.397787] wlp5s0: send auth to d4:7b:b0:3d:0e:75 (try 1/3)
[ 117.399376] wlp5s0: authenticated
[ 117.400383] wlp5s0: associate with d4:7b:b0:3d:0e:75 (try 1/3)
[ 117.401660] wlp5s0: RX AssocResp from d4:7b:b0:3d:0e:75 (capab=0x1011 status=0 aid=2)
[ 117.411401] wlp5s0: associated
[ 117.440814] IPv6: ADDRCONF(NETDEV_CHANGE): wlp5s0: link becomes ready
[ 117.452596] wlp5s0: Limiting TX power to 23 (23 - 0) dBm as advertised by d4:7b:b0:3d:0e:75
[ 155.835554] EXT4-fs (sda1): mounted filesystem with ordered data mode. Opts: (null)
root@dikke:/home/rene#
2-e exfat kaart, na verwijderen fat16-kaart zonder deze af te koppelen:
root@dikke:/home/rene# dmesg|tail
[ 424.351373] mmc0: card 0001 removed
[ 478.113252] mmc0: new SD card at address 0001
[ 478.113548] mmcblk0: mmc0:0001 SD 974 MiB
[ 478.114518] mmcblk0: p1
[ 478.587207] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 485.345828] mmc0: card 0001 removed
[ 490.730760] mmc0: cannot verify signal voltage switch
[ 490.864068] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 490.864403] mmcblk0: mmc0:aaaa SL128 119 GiB
[ 490.866792] mmcblk0: p1
root@dikke:/home/rene#
Na ontkoppelen 2-e exfat kaart, 1-e weer ingestoken, wordt aangekoppeld
root@dikke:/home/rene# dmesg|tail
[ 485.345828] mmc0: card 0001 removed
[ 490.730760] mmc0: cannot verify signal voltage switch
[ 490.864068] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 490.864403] mmcblk0: mmc0:aaaa SL128 119 GiB
[ 490.866792] mmcblk0: p1
[ 675.249920] mmc0: card aaaa removed
[ 688.339006] mmc0: cannot verify signal voltage switch
[ 688.470935] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 688.471171] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 688.473179] mmcblk0: p1
root@dikke:/home/rene#
2-e exfat kaart unmounted, niet verwijderd uit kaartrslot:
root@dikke:/home/rene# dmesg|tail
[ 485.345828] mmc0: card 0001 removed
[ 490.730760] mmc0: cannot verify signal voltage switch
[ 490.864068] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 490.864403] mmcblk0: mmc0:aaaa SL128 119 GiB
[ 490.866792] mmcblk0: p1
[ 675.249920] mmc0: card aaaa removed
[ 688.339006] mmc0: cannot verify signal voltage switch
[ 688.470935] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 688.471171] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 688.473179] mmcblk0: p1
root@dikke:/home/rene#
2-e exfat verwijderd uit kaartslot:
root@dikke:/home/rene# dmesg|tail
[ 490.730760] mmc0: cannot verify signal voltage switch
[ 490.864068] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 490.864403] mmcblk0: mmc0:aaaa SL128 119 GiB
[ 490.866792] mmcblk0: p1
[ 675.249920] mmc0: card aaaa removed
[ 688.339006] mmc0: cannot verify signal voltage switch
[ 688.470935] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 688.471171] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 688.473179] mmcblk0: p1
[ 941.821729] mmc0: card aaaa removed
root@dikke:/home/rene#
2-e exfat kaart opnieuw ingestoken, wordt niet gemount.
fat16 kaart ingestoken en verwijderd zonder te unmounten.
2-e exfat kaart opnieuw ingestoken, wordt niet gemount.
1-e exfat kaart opnieuw ingestoken, wordt gemount.
root@dikke:/home/rene# dmesg|tail
[ 941.821729] mmc0: card aaaa removed
[ 1587.720867] mmc0: new SD card at address 0001
[ 1587.721078] mmcblk0: mmc0:0001 SD 974 MiB
[ 1587.722084] mmcblk0: p1
[ 1588.204428] FAT-fs (mmcblk0p1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 1613.420969] mmc0: card 0001 removed
[ 1670.351946] mmc0: cannot verify signal voltage switch
[ 1670.484401] mmc0: new ultra high speed SDR104 SDXC card at address aaaa
[ 1670.484986] mmcblk0: mmc0:aaaa SC64G 59.5 GiB
[ 1670.486870] mmcblk0: p1
root@dikke:/home/rene#
- - - - - - - - - - - - - - - - - - - -
Wat er allemaal gebeurt lijkt niet reproduceerbaar.
Ik begin er al spijt van te krijgen dat ik de vraag gesteld heb.
Het vervelende is dat ik meestal een aantal documenten/ programma's open heb staan.
Herstarten betekent die allemaal weer openen.
Daarnaast moet ik altijd beide kaartjes van mijn fotocamera uitlezen nadat ik gefotografeerd heb. En dat doe ik veel.
Als er geen simpele oplossing is zal ik me er bij neer moeten leggen dat e.e.a. onvoorspelbaar is en dat herstarten toch nodig is.
Iedereen in ieder geval bedankt voor het meedenken,
Groeten,
René.