Re: com fer un pont entre a wifi i la ethernet

On Thu, Sep 16, 2010 at 12:13 AM, Marc Aymerich <glicerinu@gmail.com> wrote:

On Wed, Sep 15, 2010 at 11:45 PM, XAvi <xavier@esdebian.org> wrote:

me equivocat abans no era 192.168.1.111 sino 192.168.2.111

route -n

Kernel IP routing table
Destination     Gateway         Genmask         Flags Metric Ref    Use Iface
192.168.2.0     0.0.0.0         255.255.255.0   U     0      0        0 eth0
192.168.2.0     0.0.0.0         255.255.255.0   U     0      0        0 ra0
0.0.0.0         192.168.2.1     0.0.0.0         UG    0      0        0 ra0

ifconfig

eth0      Link encap:Ethernet HWaddr 00:0e:1d:fe:a0:07
          inet addr:192.168.2.111 Bcast:192.168.2.255 Mask:255.255.255.0
          UP BROADCAST MULTICAST MTU:1500 Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
          Interrupt:11 Base address:0xa000

lo        Link encap:Local Loopback
          inet addr:127.0.0.1 Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING MTU:16436 Metric:1
          RX packets:21082 errors:0 dropped:0 overruns:0 frame:0
          TX packets:21082 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0
          RX bytes:1310637 (1.2 MiB) TX bytes:1310637 (1.2 MiB)

ra0       Link encap:Ethernet HWaddr 00:0e:1d:fe:a5:05
          inet addr:192.168.2.109 Bcast:192.168.2.255 Mask:255.255.255.0
          inet6 addr: fe80::20e:1dff:fefe:a505/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
          RX packets:52432 errors:0 dropped:0 overruns:0 frame:0
          TX packets:65108 errors:2825 dropped:2825 overruns:0 carrier:0
          collisions:27982 txqueuelen:1000
          RX bytes:8122959 (7.7 MiB) TX bytes:8756192 (8.3 MiB)
          Interrupt:12 Base address:0x4000

provaré el que ha dit el peplluis. Si se vos ocorre altra cosa envieu-la. Aniré provant fins que encerte

respecta al que ha dit Orestes Mas no. No ho vullc via el router sino tal i com ho has entes abans, Es a dir a traves de el 1r ordinador que es el que es conecta a el router (clau web) i fer-lo servir per conectar amb un cable creuat al 2n que entrarà per la ethernet per gastar la wifi del 1r per navegar. Exactament com ho havies entes de primera hora.

Gràcies a tots, li pegaré per aconseguir-ho

XAvi..

Hola Xavi,

perque no proves aquest network/interfaces:

auto lo br0
iface lo inet loopback
iface eth0 inet manual

iface wlan0 inet manual
iface br0 inet static
   bridge_ports eth0 wlan0
   address 192.168.2.111

   broadcast 10.0.0.255
   netmask 255.255.255.0
   gateway 192.168.2.1

pre-up iwconfig wlan0 essid casa key s:*************

--
Marc