Re: watchdog: BUG: soft lockup - CPU#0 stuck for 23s! [systemd:1]
On 3/13/21 5:29 PM, Mike Tremaine wrote:
>> On Mar 12, 2021, at 5:56 AM,
>> Dennis Clarke <dclarke@blastwave.org> wrote:
>>
>> I have seen this for a few months now. The old old netra machine will
>> run just fine endlessly but if I attempt to perform a package update
>> then I am always assured to see :
> What kernel are you on?
Let me address that *after* we look at the hardware diagnostics. The old
Netra t1 105 is pretty much indestructible with the exception being that
the internal battery will die. Which mine has. However this affects
nothing as the machine can be left plugged in and powered on for years
and the firmware variables are trivial to setup if needed. I did do a
power down and then left it cold for a day or two. That is a good way to
see the full hardware diagnostics when the power plug is put back in.
Thus :
LOMlite console
Standby
lom>
LOM event: LOM reset
lom>poweron
lom>
LOM event: power on
ps/2 kbd check: 0000.0000.0000.00fe
LOM event: Fan 1 failed
LOM event: Fault LED 3Hz
Checking Sun KB Done
%o0 = 0000.0000.0055.4001
Executing Power On SelfTest
SPARCengine(tm)Ultra CP 1500 POST 1.17 ME created 03/06/00
WARRNING: NVRAM battery is either bad or just replaced!
Time Stamp [hour:min:sec] 33:30:02
Init POST BSS
Init System BSS
Probing system keyboard : Done
DMMU TLB Tags
DMMU TLB Tag Access Test
DMMU TLB RAM
DMMU TLB RAM Access Test
Ecache Tests
Probe Ecache
ecache_size = 0x00200000
Ecache RAM Addr Test
Ecache Tag Addr Test
Ecache RAM Test
Ecache Tag Test
Invalidate Ecache Tags
All CPU Basic Tests
V9 Instruction Test
CPU Tick and Tick Compare Reg Test
CPU Soft Trap Test
CPU Softint Reg and Int Test
All Basic MMU Tests
DMMU Primary Context Reg Test
DMMU Secondary Context Reg Test
DMMU TSB Reg Test
DMMU Tag Access Reg Test
DMMU VA Watchpoint Reg Test
DMMU PA Watchpoint Reg Test
IMMU TSB Reg Test
IMMU Tag Access Reg Test
IMMU TLB RAM Access Test
IMMU TLB Tag Access Test
All Basic Cache Tests
Dcache RAM Test
Dcache Tag Test
Icache RAM Test
Icache Tag Test
Icache Next Test
Icache Predecode Test
UltraSPARC IIi MCU Control & Status Regs Init and Tests
Init UltraSPARC IIi MCU Control & Status Regs
CPU speed : 440 Mhz, mc1 set : 0x544cb9dd
Memory Probe and Init
Probe Memory
INFO: All the memory Group in 10 bit column mode
Group 0: 256MB
Group 1: 256MB
Group 2: 256MB
Group 3: 256MB
Malloc Post Memory
Init Post Memory
..........
Memory Addr w/ Ecache
Map PROM/STACK/NVRAM in DMMU
Load Post In Memory
Run POST from MEM
..........
loaded POST in memory
Update Master Stack/Frame Pointers
All FPU Basic Tests
FPU Regs Test
FPU State Reg Test
FPU Functional Test
FPU Trap Test
Memory Tests
Init Memory
...............
................
................
................
................
................
................
................
Memory Addr w/ Ecache Test
ECC Memory Addr Test
Block Memory Addr Test
Block Memory Test
...............
...............
................
................
................
................
................
................
................
................
................
................
................
................
................
................
ECC Blk Memory Test
...............
...............
................
................
................
................
................
................
................
................
................
................
................
................
................
................
All Basic UltraSPARC IIi PBM Tests
Init UltraSPARC IIi PBM
PIO Decoder and BCT Test
PCI Byte Enable Test
UltraSPARC IIi IOMMU Regs Test
UltraSPARC IIi IOMMU RAM NTA Test
UltraSPARC IIi IOMMU CAM NTA Test
UltraSPARC IIi IOMMU RAM Address Test
UltraSPARC IIi IOMMU CAM Address Test
IOMMU TLB Compare Test
IOMMU TLB Flush Test
PBM Control/Status Reg Test
PBM Diag Reg Test
UltraSPARC IIi PBM Regs Test
All Advanced CPU Tests
DMMU Hit/Miss Test
DMMU Little Endian Test
IU ASI Access Test
FPU ASI Access Test
Ecache Thrash Test
All CPU Error Reporting Tests
CPU Addr Align Trap Test
DMMU Access Priv Page Test
DMMU Write Protected Page Test
All Advanced UltraSPARC IIi PBM Tests
Init UltraSPARC IIi PBM
Consist DMA Wr, IOMMU hit Ebus Test
All Basic Cheerio Tests
Cheerio Ebus PCI Config Space Test
Cheerio Ethernet PCI Config Space Test
Cheerio Ebus Engine Reg Test
Cheerio Init
All Basic I2c Tests
Init i2c bus
Thermister Reading Test
Thermister Position Readings (in Hex)
CPU 0x70
All Basic PCI-PCI Bridge Tests
PCI-PCI Bridge Config Space Test
All Basic Symbios 875 SCSI controller Tests
Symbios 875 SCSI controller PCI Config Space Test
Extended POST:
Start Extended POST : No EXT POST is found
Power On Selftest Completed
Status = 0000.0000.0000.0000 ffff.ffff.f100.1db0 019f.3333.3a50.0011
Software Power ON
@(#) SPARCengine(tm)Ultra CP 1500 3.10.27 ME created 2000/06/22 16:45
Enter Checking KB
ps/2 kbd check: 0000.0000.0000.00fe
Checking Sun KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing Memory
Group Info[0000.0000.0000.0003] : 0000.0000.0000.0110
Group Info[0000.0000.0000.0002] : 0000.0000.0000.0110
Group Info[0000.0000.0000.0001] : 0000.0000.0000.0110
Group Info[0000.0000.0000.0000] : 0000.0000.0000.0110
Done
Clearing Memory...Done
MEM BASE = 0000.0000.3800.0000
MEM SIZE = 0000.0000.0800.0000
MMUs ON
Copy Done
PC = 0000.01ff.f000.30dc
PC = 0000.0000.0000.3120
Decompressing into Memory Done
Size = 0000.0000.0008.7710
ttya initialized
flashprom flashprom Incorrect configuration checksum;
Setting NVRAM parameters to default values.
Setting diag-switch? NVRAM parameter to true
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
UltraSPARC-IIi Version 9.1 (E$=2 MB) 2-2 module
Advanced PCI Bridge Version 1.3
Probing Memory Group #0 128 + 128 : 256 Megabytes
Probing Memory Group #1 128 + 128 : 256 Megabytes
Probing Memory Group #2 128 + 128 : 256 Megabytes
Probing Memory Group #3 128 + 128 : 256 Megabytes
Initialise 2nd I2c controller
Environmental monitoring: Enabled
i2c adc gpio gpio
i2c Probing Floppy: No drives detected
Probing /pci@1f,0/pci@1,1 at Device 1 network
Probing /pci@1f,0/pci@1,1 at Device 2 scsi disk tape
Probing /pci@1f,0/pci@1,1 at Device 3 network
Probing /pci@1f,0/pci@1 at Device 1 pci
Probing /pci@1f,0/pci@1/pci@1 at Device 0 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 1 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 2 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 3 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 4 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 5 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 6 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 7 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 8 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 9 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device a Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device b Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device c Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device d Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device e ide disk cdrom
Probing /pci@1f,0/pci@1/pci@1 at Device f Nothing there
Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
OpenBoot 3.10.27 ME, 1024 MB memory installed, Serial #12731976.
Ethernet address 8:0:20:c2:46:48, Host ID: 80c24648.
Boot device: net File and args:
Using External Transceiver - Link Up.
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
Timeout waiting for ARP/RARP packet
~
ok
I did sent a BRK to the serial port and that drops us into the firmware
"ok" prompt. There is a failed fan but in fact the fan is entirely not
there. At all. I removed it because it had failed five or six years ago
and getting another one is just annoying. Also it is not really needed.
We can see that there is 1G of ECC memory and the memory passes all the
basic tests.
Now I setup a few of the firmware variables and reset the unit :
ok printenv
Variable Name Value Default Value
tpe-link-test? true true
scsi-initiator-id 7 7
keyboard-click? false false
keymap
watchdog-timeout 65535 65535
watchdog-enable? false false
ttyb-rts-dtr-off false false
ttyb-ignore-cd true true
ttya-rts-dtr-off false false
ttya-ignore-cd true true
ttyb-mode 9600,8,n,1,- 9600,8,n,1,-
ttya-mode 9600,8,n,1,- 9600,8,n,1,-
cpci-probe-list 0,1,2,3,4,5,6,7,8,9,a,b, ...
0,1,2,3,4,5,6,7,8,9,a,b, ...
pcia-probe-list 1 1
pcib-probe-list 1,2,3 1,2,3
mfg-mode off off
diag-level max max
d7s-flipped? false false
#power-cycles 1431655766
system-board-serial# 20 00 00 00 00 01 01 10 ...
system-board-date 00 10 00 00 10 14 01 10 ...
last-poweroff-cause 0 0
env-monitor enabled enabled
shutdown-temperature 72 72
warning-temperature 67 67
fcode-debug? false false
output-device ttya ttya
input-device ttya ttya
load-base 16384 16384
auto-boot-retry? false false
use-boot-table? false false
boot-command boot boot
auto-boot? true true
watchdog-reboot? false false
diag-file
diag-device net net
boot-file
boot-device disk net disk net
local-mac-address? false false
net-timeout 0 0
ansi-terminal? true true
screen-#columns 80 80
screen-#rows 34 34
silent-mode? false false
use-nvramrc? false false
nvramrc
security-mode none
security-password
security-#badlogins 256
oem-logo
oem-logo? false false
oem-banner
oem-banner? false false
hardware-revision 55 55 54 55 15 55 55 45 ...
last-hardware-update UUUUQUUU ...
diag-switch? true false
ok setenv #power-cycles 0
#power-cycles = 0
ok setenv auto-boot? false
auto-boot? = false
ok
Easy. Now a full reset :
ok reset-all
Resetting ...
Software Power ON
@(#) SPARCengine(tm)Ultra CP 1500 3.10.27 ME created 2000/06/22 16:45
Enter Checking KB
ps/2 kbd check: 0000.0000.0000.00fe
Checking Sun KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing Memory
Group Info[0000.0000.0000.0003] : 0000.0000.0000.0110
Group Info[0000.0000.0000.0002] : 0000.0000.0000.0110
Group Info[0000.0000.0000.0001] : 0000.0000.0000.0110
Group Info[0000.0000.0000.0000] : 0000.0000.0000.0110
Done
Clearing Memory...Done
MEM BASE = 0000.0000.3800.0000
MEM SIZE = 0000.0000.0800.0000
MMUs ON
Copy Done
PC = 0000.01ff.f000.30dc
PC = 0000.0000.0000.3120
Decompressing into Memory Done
Size = 0000.0000.0008.7710
ttya initialized
flashprom flashprom Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
UltraSPARC-IIi Version 9.1 (E$=2 MB) 2-2 module
Advanced PCI Bridge Version 1.3
Probing Memory Group #0 128 + 128 : 256 Megabytes
Probing Memory Group #1 128 + 128 : 256 Megabytes
Probing Memory Group #2 128 + 128 : 256 Megabytes
Probing Memory Group #3 128 + 128 : 256 Megabytes
Initialise 2nd I2c controller
Environmental monitoring: Enabled
i2c adc gpio gpio
i2c Probing Floppy: No drives detected
Probing /pci@1f,0/pci@1,1 at Device 1 network
Probing /pci@1f,0/pci@1,1 at Device 2 scsi disk tape
Probing /pci@1f,0/pci@1,1 at Device 3 network
Probing /pci@1f,0/pci@1 at Device 1 pci
Probing /pci@1f,0/pci@1/pci@1 at Device 0 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 1 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 2 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 3 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 4 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 5 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 6 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 7 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 8 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device 9 Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device a Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device b Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device c Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device d Nothing there
Probing /pci@1f,0/pci@1/pci@1 at Device e ide disk cdrom
Probing /pci@1f,0/pci@1/pci@1 at Device f Nothing there
Netra t1 (UltraSPARC-IIi 440MHz), No Keyboard
OpenBoot 3.10.27 ME, 1024 MB memory installed, Serial #12731976.
Ethernet address 8:0:20:c2:46:48, Host ID: 80c24648.
ok
So finally boot the thing to the grub prompt :
ok
ok boot disk0
Boot device: /pci@1f,0/pci@1,1/scsi@2/disk@0,0 File and args:
GRUB Loading kernel...
Welcome to GRUB!
Here I select the "Advanced options for Debian GNU/Linux" and then I
want "Debian GNU/Linux, with Linux 5.10.0-1-sparc64 (recovery mode)" but
I want this to be verbose :
linux /vmlinux-5.10.0-1-sparc64 root=UUID=3e726aa3-b\
1f1-4d65-be35-1436d9a04164 ro single verbose
Then thankfully CTRL-X does work fine :
[ 0.000150] PROMLIB: Sun IEEE Boot Prom 'OBP 3.10.27 2000/06/22 16:45'
[ 0.000244] PROMLIB: Root node compatible: sun4u
[ 0.000543] Linux version 5.10.0-1-sparc64
(debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-5) 10.2.1
20210108, GNU ld (GNU Binutils for Debian) 2.35.1) #1 Debian 5.10.5-1
(2021-01-09)
[ 0.336935] printk: bootconsole [earlyprom0] enabled
[ 0.396183] ARCH: SUN4U
[ 0.425389] Ethernet address: 08:00:20:c2:46:48
[ 0.479389] MM: PAGE_OFFSET is 0xfffff80000000000 (max_phys_bits == 40)
[ 0.558385] MM: VMALLOC [0x0000000100000000 --> 0x0000060000000000]
[ 0.633248] MM: VMEMMAP [0x0000060000000000 --> 0x00000c0000000000]
[ 0.711344] Kernel: Using 4 locked TLB entries for main kernel image.
[ 0.787508] Remapping the kernel...
[ 0.833324] done.
[ 0.376682] OF stdout device is: /pci@1f,0/pci@1,1/ebus@1/su@14,3803f8
[ 0.453816] PROM: Built device tree with 87107 bytes of memory.
[ 0.524799] Top of RAM: 0x3fec0000, Total RAM: 0x3feb4000
[ 0.588983] Memory hole size: 0MB
[ 0.639857] Allocated 16384 bytes for kernel page tables.
[ 0.703643] Zone ranges:
[ 0.733615] Normal [mem 0x0000000000000000-0x000000003febffff]
[ 0.807437] Movable zone start for each node
[ 0.858386] Early memory node ranges
[ 0.901022] node 0: [mem 0x0000000000000000-0x000000003fdfdfff]
[ 0.975890] node 0: [mem 0x000000003fe00000-0x000000003fe9ffff]
[ 1.050750] node 0: [mem 0x000000003feaa000-0x000000003febffff]
[ 1.125704] Zeroed struct page in unavailable ranges: 166 pages
[ 1.125719] Initmem setup node 0 [mem
0x0000000000000000-0x000000003febffff]
[ 1.344220] Booting Linux...
[ 1.377766] CPU CAPS: [flush,stbar,swap,muldiv,v9,mul32,div32,v8plus]
[ 1.454698] CPU CAPS: [vis]
[ 1.497630] Built 1 zonelists, mobility grouping on. Total pages: 129755
[ 1.577923] Kernel command line: BOOT_IMAGE=/vmlinux-5.10.0-1-sparc64
root=UUID=3e726aa3-b1f1-4d65-be35-1436d9a04164 ro single verbose
[ 1.736779] Dentry cache hash table entries: 131072 (order: 7,
1048576 bytes, linear)
[ 1.833540] Inode-cache hash table entries: 65536 (order: 6, 524288
bytes, linear)
[ 1.923125] Sorting __ex_table...
[ 1.964854] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 2.108513] Memory: 994048K/1047248K available (8078K kernel code,
1425K rwdata, 2152K rodata, 496K init, 405K bss, 53200K reserved, 0K
cma-reserved)
[ 2.267971] random: get_random_u64 called from
__kmem_cache_create+0x20/0x420 with crng_init=0
[ 2.270696] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 2.451388] ftrace: allocating 25693 entries in 51 pages
[ 2.579233] ftrace: allocated 51 pages with 4 groups
[ 2.669744] NR_IRQS: 2048, nr_irqs: 2048, preallocated irqs: 1
[ 2.739236] clocksource: tick: mask: 0xffffffffffffffff max_cycles:
0x657b4868ff, max_idle_ns: 440795220381 ns
[ 2.858200] clocksource: mult[245cb72] shift[24]
[ 2.913305] clockevent: mult[70a500d6] shift[32]
[ 2.968675] Console: colour dummy device 80x25
[ 3.021504] printk: console [tty0] enabled
[ 3.070323] printk: bootconsole [earlyprom0] disabled
[ 0.000150] PROMLIB: Sun IEEE Boot Prom 'OBP 3.10.27 2000/06/22 16:45'
[ 0.000244] PROMLIB: Root node compatible: sun4u
[ 0.000543] Linux version 5.10.0-1-sparc64
(debian-kernel@lists.debian.org) (gcc-10 (Debian 10.2.1-5) 10.2.1
20210108, GNU ld (GNU Binutils for Debian) 2.35.1) #1 Debian 5.10.5-1
(2021-01-09)
[ 0.336935] printk: bootconsole [earlyprom0] enabled
[ 0.396183] ARCH: SUN4U
[ 0.425389] Ethernet address: 08:00:20:c2:46:48
[ 0.479389] MM: PAGE_OFFSET is 0xfffff80000000000 (max_phys_bits == 40)
[ 0.558385] MM: VMALLOC [0x0000000100000000 --> 0x0000060000000000]
[ 0.633248] MM: VMEMMAP [0x0000060000000000 --> 0x00000c0000000000]
[ 0.711344] Kernel: Using 4 locked TLB entries for main kernel image.
[ 0.787508] Remapping the kernel...
[ 0.833324] done.
[ 0.376682] OF stdout device is: /pci@1f,0/pci@1,1/ebus@1/su@14,3803f8
[ 0.453816] PROM: Built device tree with 87107 bytes of memory.
[ 0.524799] Top of RAM: 0x3fec0000, Total RAM: 0x3feb4000
[ 0.588983] Memory hole size: 0MB
[ 0.639857] Allocated 16384 bytes for kernel page tables.
[ 0.703643] Zone ranges:
[ 0.733615] Normal [mem 0x0000000000000000-0x000000003febffff]
[ 0.807437] Movable zone start for each node
[ 0.858386] Early memory node ranges
[ 0.901022] node 0: [mem 0x0000000000000000-0x000000003fdfdfff]
[ 0.975890] node 0: [mem 0x000000003fe00000-0x000000003fe9ffff]
[ 1.050750] node 0: [mem 0x000000003feaa000-0x000000003febffff]
[ 1.125704] Zeroed struct page in unavailable ranges: 166 pages
[ 1.125719] Initmem setup node 0 [mem
0x0000000000000000-0x000000003febffff]
[ 1.344220] Booting Linux...
[ 1.377766] CPU CAPS: [flush,stbar,swap,muldiv,v9,mul32,div32,v8plus]
[ 1.454698] CPU CAPS: [vis]
[ 1.497630] Built 1 zonelists, mobility grouping on. Total pages: 129755
[ 1.577923] Kernel command line: BOOT_IMAGE=/vmlinux-5.10.0-1-sparc64
root=UUID=3e726aa3-b1f1-4d65-be35-1436d9a04164 ro single verbose
[ 1.736779] Dentry cache hash table entries: 131072 (order: 7,
1048576 bytes, linear)
[ 1.833540] Inode-cache hash table entries: 65536 (order: 6, 524288
bytes, linear)
[ 1.923125] Sorting __ex_table...
[ 1.964854] mem auto-init: stack:off, heap alloc:on, heap free:off
[ 2.108513] Memory: 994048K/1047248K available (8078K kernel code,
1425K rwdata, 2152K rodata, 496K init, 405K bss, 53200K reserved, 0K
cma-reserved)
[ 2.267971] random: get_random_u64 called from
__kmem_cache_create+0x20/0x420 with crng_init=0
[ 2.270696] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 2.451388] ftrace: allocating 25693 entries in 51 pages
[ 2.579233] ftrace: allocated 51 pages with 4 groups
[ 2.669744] NR_IRQS: 2048, nr_irqs: 2048, preallocated irqs: 1
[ 2.739236] clocksource: tick: mask: 0xffffffffffffffff max_cycles:
0x657b4868ff, max_idle_ns: 440795220381 ns
[ 2.858200] clocksource: mult[245cb72] shift[24]
[ 2.913305] clockevent: mult[70a500d6] shift[32]
[ 2.968675] Console: colour dummy device 80x25
[ 3.021504] printk: console [tty0] enabled
[ 3.070323] printk: bootconsole [earlyprom0] disabled
[ 3.210745] Calibrating delay using timer specific routine.. 882.26
BogoMIPS (lpj=1764532)
[ 3.210796] pid_max: default: 32768 minimum: 301
[ 3.211313] LSM: Security Framework initializing
[ 3.211575] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 3.212365] AppArmor: AppArmor initialized
[ 3.212407] TOMOYO Linux initialized
[ 3.212711] Mount-cache hash table entries: 2048 (order: 1, 16384
bytes, linear)
[ 3.212807] Mountpoint-cache hash table entries: 2048 (order: 1,
16384 bytes, linear)
[ 3.220341] devtmpfs: initialized
[ 3.227023] Performance events: No support for PMU type 'ultra12'
[ 3.228666] clocksource: jiffies: mask: 0xffffffff max_cycles:
0xffffffff, max_idle_ns: 7645041785100000 ns
[ 3.228742] futex hash table entries: 256 (order: -1, 6144 bytes, linear)
[ 3.231307] NET: Registered protocol family 16
[ 3.244320] IRQ pre handler NOT supported.
[ 3.246594] audit: initializing netlink subsys (disabled)
[ 3.248194] thermal_sys: Registered thermal governor 'fair_share'
[ 3.248208] thermal_sys: Registered thermal governor 'step_wise'
[ 3.254717] pci@1f,0: PCI IO [io 0x1fe02000000-0x1fe02ffffff] offset
1fe02000000
[ 3.254798] pci@1f,0: PCI MEM [mem 0x1ff00000000-0x1ffffffffff]
offset 1ff00000000
[ 3.254868] audit: type=2000 audit(0.128:1): state=initialized
audit_enabled=0 res=1
[ 3.254940] pci@1f,0: SABRE PCI Bus Module ver[0:0]
[ 3.255006] PCI: Scanning PBM /pci@1f,0
[ 3.256591] sabre f00694e0: PCI host bridge to bus 0000:00
[ 3.256653] pci_bus 0000:00: root bus resource [io
0x1fe02000000-0x1fe02ffffff] (bus address [0x0000-0xffffff])
[ 3.256709] pci_bus 0000:00: root bus resource [mem
0x1ff00000000-0x1ffffffffff] (bus address [0x00000000-0xffffffff])
[ 3.256765] pci_bus 0000:00: root bus resource [bus 00-03]
[ 3.256875] pci 0000:00:01.1: [108e:5000] type 01 class 0x060400
[ 3.257431] pci_bus 0000:01: extended config space not accessible
[ 3.258733] pci 0000:01:01.0: [108e:1000] type 00 class 0x068000
[ 3.259220] pci 0000:01:01.1: [108e:1001] type 00 class 0x020000
[ 3.259274] pci 0000:01:01.1: reg 0x10: [mem 0x1ffe0000000-0x1ffe000701f]
[ 3.259687] pci 0000:01:02.0: [1000:000f] type 00 class 0x010000
[ 3.259738] pci 0000:01:02.0: reg 0x10: [io 0x1fe02c00000-0x1fe02c000ff]
[ 3.259778] pci 0000:01:02.0: reg 0x14: [mem 0x1ffe0008000-0x1ffe00080ff]
[ 3.259817] pci 0000:01:02.0: reg 0x18: [mem 0x1ffe000a000-0x1ffe000afff]
[ 3.260277] pci 0000:01:03.1: [108e:1001] type 00 class 0x020000
[ 3.260328] pci 0000:01:03.1: reg 0x10: [mem 0x1ffe0010000-0x1ffe001701f]
[ 3.260732] pci 0000:00:01.0: [108e:5000] type 01 class 0x060400
[ 3.261269] pci_bus 0000:02: extended config space not accessible
[ 3.261757] pci 0000:02:01.0: [1011:0022] type 01 class 0x060400
[ 3.262381] pci_bus 0000:03: extended config space not accessible
[ 3.262745] pci 0000:02:01.0: PCI bridge to [bus 03]
[ 3.262795] pci 0000:02:01.0: bridge window [io
0x1fe02001000-0x1fe02001fff]
[ 3.262910] pci 0000:03:0e.0: [1095:0646] type 00 class 0x01018f
[ 3.262955] pci 0000:03:0e.0: reg 0x10: [io 0x1fe02001000-0x1fe02001007]
[ 3.262994] pci 0000:03:0e.0: reg 0x14: [io 0x1fe02001008-0x1fe0200100b]
[ 3.263053] pci 0000:03:0e.0: reg 0x18: [io 0x1fe02001010-0x1fe02001017]
[ 3.263095] pci 0000:03:0e.0: reg 0x1c: [io 0x1fe02001018-0x1fe0200101b]
[ 3.263133] pci 0000:03:0e.0: reg 0x20: [io 0x1fe02001020-0x1fe0200102f]
[ 3.274131] HugeTLB registered 64.0 KiB page size, pre-allocated 0 pages
[ 3.274188] HugeTLB registered 8.00 MiB page size, pre-allocated 0 pages
[ 3.274224] HugeTLB registered 256 MiB page size, pre-allocated 0 pages
[ 3.274261] HugeTLB registered 2.00 GiB page size, pre-allocated 0 pages
[ 8.656595] iommu: Default domain type: Translated
[ 8.657029] vgaarb: loaded
[ 8.659927] NetLabel: Initializing
[ 8.659967] NetLabel: domain hash size = 128
[ 8.659993] NetLabel: protocols = UNLABELED CIPSOv4 CALIPSO
[ 8.660225] NetLabel: unlabeled traffic allowed by default
[ 8.660926] /pci@1f,0/pci@1,1/ebus@1/eeprom@14,0: Mostek regs at
0x1fff1000000
[ 8.661876] AUXIO: Found device at
/pci@1f,0/pci@1,1/ebus@1/auxio@14,726000
[ 8.662458] clocksource: Switched to clocksource tick
[ 8.832572] VFS: Disk quotas dquot_6.6.0
[ 8.832961] VFS: Dquot-cache hash table entries: 1024 (order 0, 8192
bytes)
[ 8.835397] AppArmor: AppArmor Filesystem Enabled
[ 8.855565] NET: Registered protocol family 2
[ 8.857724] tcp_listen_portaddr_hash hash table entries: 512 (order:
0, 8192 bytes, linear)
[ 8.858120] TCP established hash table entries: 8192 (order: 3, 65536
bytes, linear)
[ 8.858854] TCP bind hash table entries: 8192 (order: 3, 65536 bytes,
linear)
[ 8.859289] TCP: Hash tables configured (established 8192 bind 8192)
[ 8.859871] UDP hash table entries: 512 (order: 1, 16384 bytes, linear)
[ 8.860089] UDP-Lite hash table entries: 512 (order: 1, 16384 bytes,
linear)
[ 8.860909] NET: Registered protocol family 1
[ 8.860988] NET: Registered protocol family 44
[ 8.861206] PCI: CLS 64 bytes, default 64
[ 8.861898] Trying to unpack rootfs image as initramfs...
[ 12.212477] Freeing initrd memory: 22096K
[ 12.213039] power: Control reg at 1fff1724000
[ 12.216912] Initialise system trusted keyrings
[ 12.217110] Key type blacklist registered
[ 12.217806] workingset: timestamp_bits=46 max_order=17 bucket_order=0
[ 12.237080] zbud: loaded
[ 12.239572] integrity: Platform Keyring initialized
[ 12.239627] Key type asymmetric registered
[ 12.239663] Asymmetric key parser 'x509' registered
[ 12.239818] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 252)
[ 12.240307] io scheduler mq-deadline registered
[ 12.244281] f006b9fc: ttyS0 at MMIO 0x1fff13803f8 (irq = 5, base_baud
= 115387) is a 16550A
[ 12.244343] Console: ttyS0 (SU)
[ 22.827690] printk: console [ttyS0] enabled
[ 22.883564] f006d240: ttyS1 at MMIO 0x1fff13602f8 (irq = 6, base_baud
= 115387) is a 16550A
[ 22.996286] mousedev: PS/2 mouse device common for all mice
[ 23.074818] rtc-m48t59 rtc-m48t59.0: IRQ index 0 not found
[ 23.147559] rtc-m48t59 rtc-m48t59.0: registered as rtc0
[ 23.216279] rtc-m48t59 rtc-m48t59.0: hctosys: unable to read the
hardware clock
[ 23.312888] ledtrig-cpu: registered to indicate activity on CPUs
[ 23.393792] NET: Registered protocol family 10
[ 23.582874] Segment Routing with IPv6
[ 23.631448] mip6: Mobile IPv6
[ 23.670441] NET: Registered protocol family 17
[ 23.729161] mpls_gso: MPLS GSO support
[ 23.778922] registered taskstats version 1
[ 23.832799] Loading compiled-in X.509 certificates
[ 25.123021] Loaded X.509 cert 'Debian Secure Boot CA:
6ccece7e4c6c0d1f6149f3dd27dfcc5cbb419ea1'
[ 25.237711] Loaded X.509 cert 'Debian Secure Boot Signer 2020:
00b55eb3b9'
[ 25.328557] zswap: loaded using pool lzo/zbud
[ 25.386968] Key type ._fscrypt registered
[ 25.439661] Key type .fscrypt registered
[ 25.491185] Key type fscrypt-provisioning registered
[ 25.556954] AppArmor: AppArmor sha1 policy hashing enabled
[ 25.638272] This architecture does not have kernel memory protection.
[ 25.722972] Run /init as init process
Loading, please wait...
Starting version 247.2-4
[ 26.860422] sunhme: module verification failed: signature and/or
required key missing - tainting kernel
[ 27.060189] SCSI subsystem initialized
[ 27.336195] sym53c8xx 0000:01:02.0: enabling device (0146 -> 0147)
[ 27.464883] scsi host0: pata_cmd64x
[ 27.514792] hme 0000:01:01.1: enabling device (0000 -> 0002)
[ 27.593947] scsi host1: pata_cmd64x
[ 27.641107] sym0: <875> rev 0x3 at pci 0000:01:02.0 irq 13
[ 27.714970] ata1: PATA max MWDMA2 cmd 0x1fe02001000 ctl 0x1fe02001008
bmdma 0x1fe02001020 irq 15
[ 27.830604] ata2: PATA max MWDMA2 cmd 0x1fe02001010 ctl 0x1fe02001018
bmdma 0x1fe02001028 irq 15
[ 27.946826] sunhme.c:v3.10 August 26, 2008 David S. Miller
(davem@davemloft.net)
[ 28.133905] sym0: No NVRAM, ID 7, Fast-20, SE, parity checking
[ 28.226805] eth0: HAPPY MEAL (PCI/CheerIO) 10/100BaseT Ethernet
[ 28.226820] 08:00:20:c2:46:48
[ 28.351955] sym0: SCSI BUS has been reset.
[ 28.405818] scsi host2: sym-2.2.3
[ 28.489885] hme 0000:01:03.1: enabling device (0000 -> 0002)
[ 28.604654] eth1: HAPPY MEAL (PCI/CheerIO) 10/100BaseT Ethernet
[ 28.604668] 08:00:20:c2:46:48
[ 28.754364] hme 0000:01:03.1 enp1s3f1: renamed from eth1
[ 28.826843] hme 0000:01:01.1 enp1s1f1: renamed from eth0
[ 31.470920] scsi 2:0:0:0: Direct-Access SEAGATE ST318404LSUN18G
5221 PQ: 0 ANSI: 3
[ 31.577549] scsi target2:0:0: tagged command queuing enabled, command
queue depth 16.
[ 31.680720] scsi target2:0:0: Beginning Domain Validation
[ 31.759929] scsi target2:0:0: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns,
offset 16)
[ 31.859847] scsi target2:0:0: Domain Validation skipping write tests
[ 31.943434] scsi target2:0:0: Ending Domain Validation
[ 32.014018] scsi 2:0:1:0: Direct-Access SEAGATE ST318404LSUN18G
8590 PQ: 0 ANSI: 3
[ 32.120590] scsi target2:0:1: tagged command queuing enabled, command
queue depth 16.
[ 32.223760] scsi target2:0:1: Beginning Domain Validation
[ 32.302948] scsi target2:0:1: FAST-20 WIDE SCSI 40.0 MB/s ST (50 ns,
offset 16)
[ 32.402922] scsi target2:0:1: Domain Validation skipping write tests
[ 32.486509] scsi target2:0:1: Ending Domain Validation
[ 36.476422] sd 2:0:0:0: Power-on or device reset occurred
[ 36.548364] sd 2:0:1:0: Power-on or device reset occurred
[ 36.620250] sd 2:0:0:0: [sda] 35378533 512-byte logical blocks: (18.1
GB/16.9 GiB)
[ 36.720040] sd 2:0:1:0: [sdb] 35378533 512-byte logical blocks: (18.1
GB/16.9 GiB)
[ 36.825662] sd 2:0:1:0: [sdb] Write Protect is off
[ 36.888823] sd 2:0:0:0: [sda] Write Protect is off
[ 36.953967] sd 2:0:1:0: [sdb] Write cache: disabled, read cache:
enabled, supports DPO and FUA
[ 37.067387] sd 2:0:0:0: [sda] Write cache: disabled, read cache:
enabled, supports DPO and FUA
[ 37.198270] sdb: sdb1 sdb2 sdb3 sdb4 sdb5 sdb6 sdb7 sdb8
[ 37.269752] sda: sda1 sda2 sda3 sda4
[ 37.331118] sd 2:0:0:0: [sda] Attached SCSI disk
[ 37.402899] sd 2:0:1:0: [sdb] Attached SCSI disk
[ 37.753276] random: fast init done
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top
... done.
Begin: Running /scripts/local-premount ... done.
Begin: Will now check root file system ... fsck from util-linux 2.36.1
[/sbin/fsck.ext4 (1) -- /dev/sda2] fsck.ext4 -a -C0 /dev/sda2
/dev/sda2: recovering journal
[ 88.816750] random: crng init done
/dev/sda2: Clearing orphaned inode 654139 (uid=0, gid=0, mode=0100644,
size=36624)
/dev/sda2: Clearing orphaned inode 658478 (uid=0, gid=0, mode=0100644,
size=153440)
/dev/sda2: Clearing orphaned inode 658310 (uid=0, gid=0, mode=0100755,
size=1071888)
/dev/sda2: Clearing orphaned inode 661016 (uid=0, gid=0, mode=0100755,
size=258912)
/dev/sda2: Clearing orphaned inode 6610[ 89.995218] crc32c_sparc64:
sparc64 crc32c opcode not available.
14 (uid=0, gid=0, mode=0100755, size=159000)
/dev/sda2: Clearing orphaned inode 661000 (uid=0, gid=0, mode=0100755,
size=1702256)
/dev/sda2: Clearing orphaned inode 654542 (uid=0, gid=0, mod[
90.284993] EXT4-fs (sda2): mounted filesystem with ordered data mode.
Opts: (null)
e=0100644, size=2584584)
/dev/sda2: Clearing orphaned inode 663150 (uid=0, gid=0, mode=0100644,
size=445600)
/dev/sda2: Clearing orphaned inode 654417 (uid=0, gid=0, mode=0100644,
size=715000)
/dev/sda2: Clearing orphaned inode 663146 (uid=0, gid=0, mode=0100644,
size=227768)
/dev/sda2: Clearing orphaned inode 654386 (uid=0, gid=0, mode=0100644,
size=808616)
/dev/sda2: Clearing orphaned inode 657782 (uid=0, gid=0, mode=0100755,
size=65000)
/dev/sda2: Clearing orphaned inode 657778 (uid[ 90.899027] Not
activating Mandatory Access Control as /sbin/tomoyo-init does not exist.
=0, gid=0, mode=0100600, size=72312)
/dev/sda2: Clearing orphaned inode 656102 (uid=0, gid=0, mode=0100644,
size=368408)
/dev/sda2: Clearing orphaned inode 656113 (uid=0, gid=0, mode=0100644,
size=165480)
/dev/sda2: Clearing orphaned inode 657495 (uid=0, gid=0, mode=0100644,
size=36488)
/dev/sda2: Clearing orphaned inode 655748 (uid=0, gid=0, mode=0100644,
size=321680)
/dev/sda2: Clearing orphaned inode 525606 (uid=0, gid=0, mode=0100644,
size=391565)
/dev/sda2: clean, 47529/1013824 files, 629339/4049080 blocks
done.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 92.245962] systemd[1]: System time before build time, advancing clock.
[ 92.581158] systemd[1]: Inserted module 'autofs4'
[ 92.948572] systemd[1]: systemd 247.3-1 running in system mode. (+PAM
+AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP
+GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD -SECCOMP +BLKID +ELFUTILS +KMOD
+IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 93.242159] systemd[1]: Detected architecture sparc64.
Welcome to Debian GNU/Linux bullseye/sid!
[ 93.407914] systemd[1]: Set hostname to <ceres>.
[ 96.605030] systemd[1]: Queued start job for default target Rescue Mode.
[ 96.704166] systemd[1]: Created slice system-modprobe.slice.
[ OK ] Created slice system-modprobe.slice.
[ 96.858820] systemd[1]: Created slice system-systemd\x2dfsck.slice.
[ OK ] Created slice system-systemd\x2dfsck.slice.
[ 97.032609] systemd[1]: Started Dispatch Password Requests to Console
Directory Watch.
[ OK ] Started Dispatch Password b&ts to Console Directory Watch.
[ 97.245493] systemd[1]: Set up automount Arbitrary Executable File
Formats File System Automount Point.
[ OK ] Set up automount Arbitraryb&s File System Automount Point.
[ 97.476173] systemd[1]: Reached target Local Encrypted Volumes.
[ OK ] Reached target Local Encrypted Volumes.
[ 97.633471] systemd[1]: Listening on fsck to fsckd communication Socket.
[ OK ] Listening on fsck to fsckd communication Socket.
[ 97.817886] systemd[1]: Listening on Journal Audit Socket.
[ OK ] Listening on Journal Audit Socket.
[ 97.969139] systemd[1]: Listening on Journal Socket (/dev/log).
[ OK ] Listening on Journal Socket (/dev/log).
[ 98.137336] systemd[1]: Listening on Journal Socket.
[ OK ] Listening on Journal Socket.
[ 98.285795] systemd[1]: Listening on udev Control Socket.
[ OK ] Listening on udev Control Socket.
[ 98.436955] systemd[1]: Listening on udev Kernel Socket.
[ OK ] Listening on udev Kernel Socket.
[ 98.595161] systemd[1]: Mounting Huge Pages File System...
Mounting Huge Pages File System...
[ 98.755808] systemd[1]: Mounting POSIX Message Queue File System...
Mounting POSIX Message Queue File System...
[ 98.944046] systemd[1]: Mounting Kernel Debug File System...
Mounting Kernel Debug File System...
[ 99.129496] systemd[1]: Mounting Kernel Trace File System...
Mounting Kernel Trace File System...
[ 99.312949] systemd[1]: Starting Set the console keyboard layout...
Starting Set the console keyboard layout...
[ 99.491286] systemd[1]: Starting Create list of static device nodes
for the current kernel...
Starting Create list of stb&odes for the current kernel...
[ 99.716828] systemd[1]: Starting Load Kernel Module configfs...
Starting Load Kernel Module configfs...
[ 99.901465] systemd[1]: Starting Load Kernel Module fuse...
[ 100.084072] fuse: init (API version 7.32)
Starting Load Kernel Module fuse...
[ 100.242945] systemd[1]: Condition check resulted in Set Up Additional
Binary Formats being skipped.
[ 100.479937] systemd[1]: Condition check resulted in File System Check
on Root Device being skipped.
[ 100.757612] systemd[1]: Starting Journal Service...
Starting Journal Service...
[ 101.057538] systemd[1]: Starting Load Kernel Modules...
Starting Load Kernel Modules...
[ 101.416276] systemd[1]: Starting Remount Root and Kernel File Systems...
Starting Remount Root and Kernel File Systems...
[ 101.883390] EXT4-fs (sda2): re-mounted. Opts: errors=remount-ro
[ 101.973534] systemd[1]: Starting Coldplug All udev Devices...
Starting Coldplug All udev Devices...
[ 102.326974] systemd[1]: Started Journal Service.
[ OK ] Started Journal Service.
[ OK ] Mounted Huge Pages File System.
[ OK ] Mounted POSIX Message Queue File System.
[ OK ] Mounted Kernel Debug File System.
[ OK ] Mounted Kernel Trace File System.
[ OK ] Finished Create list of stb& nodes for the current kernel.
[ OK ] Finished Load Kernel Module configfs.
[ OK ] Finished Load Kernel Module fuse.
[ OK ] Finished Load Kernel Modules.
[ OK ] Finished Remount Root and Kernel File Systems.
Mounting FUSE Control File System...
Mounting Kernel Configuration File System...
Starting Flush Journal to Persistent Storage...
Starting Load/Save Random Seed...
Starting Apply Kernel Variables...
Starting 104.060008] systemd-journald[174]: Received client
request to flush runtime journal.
9mCreate System Users...
[ OK ] Finished Set the console keyboard layout.
[ OK ] Mounted FUSE Control File System.
[ OK ] Mounted Kernel Configuration File System.
[ OK ] Finished Load/Save Random Seed.
[ OK ] Finished Apply Kernel Variables.[ 104.708686]
systemd-journald[174]: File
/var/log/journal/4a727eeed1c9429f860a24d0362f23de/system.journal
corrupted or uncleanly shut down, renaming and replacing.
[ OK ] Finished Coldplug All udev Devices.
[ OK ] Finished Create System Users.
Starting Create Static Device Nodes in /dev...
[ OK ] Finished Flush Journal to Persistent Storage.
[ OK ] Finished Create Static Device Nodes in /dev.
[ OK ] Reached target Local File Systems (Pre).
Starting Rule-based Manageb&for Device Events and Files...
[ OK ] Started Rule-based Manager for Device Events and Files.
[ 107.307305] /pci@1f,0/pci@1,1/ebus@1/flashprom@10,0: OBP Flash, RD
1fff0000000[100000] WR 1fff0000000[100000]
[ 107.539485] d7s: 7-Segment
Display/pci@1f,0/pci@1,1/ebus@1/display7seg@14,200040 at [
(FLIPPED):0x1fff1200040]
[ 107.679253] envctrl: Initialized
[ 107.679267] [gpio 0x72]
[ 107.722853] [gpio 0x70]
[ 107.756050] [adc 0x9e]
[ 108.184098] sd 2:0:0:0: Attached scsi generic sg0 type 0
[ 108.367514] /pci@1f,0/pci@1,1/ebus@1/flashprom@10,400000: OBP Flash,
RD 1fff0400000[200000] WR 1fff0400000[200000]
[* ] (1 of 2) A start job is running forb&aac[ 108.563316] sd
2:0:1:0: Attached scsi generic sg1 type 0
[ 108.667460] envctrl: probe of f0088200 failed with error -22
[** ] (1 of 2) A start job is running forb&aac1-21d8b95f317f (12s /
1min 30s)
[*** ] (1 of 2) A start job is running forb&aac1-21d8b95f317f (12s /
1min 30s)
[ 109.662860] /pci@1f,0/pci@1,1/ebus@1/flashprom@10,800000: OBP Flash,
RD 1fff0[ OK ] Found device ST318404LSUN18G.
[ 110.534730] flash: probe of f0085c48 failed with error -16
[ OK ] Found device ST318404LSUN18G 4.
Activating swap /dev/disk/b&314c-428d-a705-de972bb638f2...
Starting File System Checkb&a339-47c5-aac1-21d8b95f317f...
[ 113.428077] Adding 992704k swap on /dev/sda4. Priority:-2 extents:1
across:992704k FS
[ OK ] Activated swap /dev/disk/bb&d-314c-428d-a705-de972bb638f2.
[ OK ] Found device Happy Meal 10/100 Ethernet [hme].
[ OK ] Reached target Swap.
[ OK ] Started File System Check Daemon to report status.
[ OK ] Finished File System Checkb&2-a339-47c5-aac1-21d8b95f317f.
Mounting /boot...
[ 132.217113] EXT4-fs (sda1): mounting ext2 file system using the ext4
subsystem
[ 133.115924] EXT4-fs (sda1): mounted filesystem without journal. Opts:
(null)
[ 133.957017] ext2 filesystem being mounted at /boot supports
timestamps until 2038 (0x7fffffff)
[ OK ] Mounted /boot.
[ OK ] Reached target Local File Systems.
[ OK ] Started ifup for enp1s1f1.
Starting Create Volatile Files and Directories...
[ OK ] Finished Create Volatile Files and Directories.
Starting Update UTMP about System Boot/Shutdown...
[ OK ] Finished Update UTMP about System Boot/Shutdown.
[ OK ] Reached target System Initialization.
[ OK ] Started Rescue Shell.
[ OK ] Reached target Rescue Mode.
Starting Update UTMP about System Runlevel Changes...
[ 139.956457] enp1s1f1: Link is up using
[ 139.956480] external
[ 140.006864] transceiver at
[ 140.036714] 100Mb/s, Full Duplex.
[ OK ] Finished Update UTMP about System Runlevel Changes.
You are in rescue mode. After logging in, type "journalctl -xb" to view
system logs, "systemctl reboot" to reboot, "systemctl default" or "exit"
to boot into default mode.
Give root password for maintenance
root@ceres:~# uname -a
Linux ceres 5.10.0-1-sparc64 #1 Debian 5.10.5-1 (2021-01-09) sparc64
GNU/Linux
root@ceres:~#
That answers the question about the Linux kernel version as well as all
the data anyone would want about the hardware. Yes that is a 100Mbit old
happy meal and I think that was renamed in the boot process to enp1s1f1
and yes it is working :
ceres# ip link show
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN mode
DEFAULT group default qlen 1000
link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
2: enp1s1f1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN mode DEFAULT group default qlen 1000
link/ether 08:00:20:c2:46:48 brd ff:ff:ff:ff:ff:ff
3: enp1s3f1: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN mode
DEFAULT group default qlen 1000
link/ether 08:00:20:c2:46:48 brd ff:ff:ff:ff:ff:ff
ceres#
However there must be a bug somewhere because the physical MAC address
is the same on both interfaces.
Regardless :
ceres#
ceres# ip addr show dev enp1s1f1
2: enp1s1f1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast
state UNKNOWN group default qlen 1000
link/ether 08:00:20:c2:46:48 brd ff:ff:ff:ff:ff:ff
inet 172.16.35.61/26 brd 172.16.35.63 scope global enp1s1f1
valid_lft forever preferred_lft forever
inet6 2607:fea8:99a0:fab0:a00:20ff:fec2:4648/64 scope global dynamic
mngtmpaddr
valid_lft 172790sec preferred_lft 172790sec
inet6 fe80::a00:20ff:fec2:4648/64 scope link
valid_lft forever preferred_lft forever
ceres#
SystemD claims we are running just fine :
ceres#
ceres# LC_ALL=C systemctl status
* ceres
State: running
Jobs: 0 queued
Failed: 0 units
Since: Thu 1970-01-01 00:01:28 GMT; 51 years 2 months ago
CGroup: /
|-user.slice
| `-user-0.slice
| |-session-1.scope
| | |- 305 /bin/login -p --
| | |-1534 -bash
| | |-1560 systemctl status
| | `-1561 pager
| `-user@0.service ...
| `-init.scope
| |-1515 /lib/systemd/systemd --user
| `-1516 (sd-pam)
|-init.scope
| `-1 /sbin/init single verbose
`-system.slice
|-systemd-udevd.service
| `-189 /lib/systemd/systemd-udevd
|-cron.service
| `-267 /usr/sbin/cron -f
|-systemd-journald.service
| `-174 /lib/systemd/systemd-journald
|-ssh.service
| `-312 sshd: /usr/sbin/sshd -D [listener] 0 of 10-100 startups
|-rsyslog.service
| `-277 /usr/sbin/rsyslogd -n -iNONE
|-ntp.service
| `-307 /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 106:112
|-dbus.service
| `-269 /usr/bin/dbus-daemon --system --address=systemd:
--nofork >
|-system-getty.slice
| `-getty@tty1.service
| `-304 /sbin/agetty -o -p -- \x5cu --noclear tty1 linux
`-systemd-logind.service
`-290 /lib/systemd/systemd-logind
ceres#
OKay so that will get us to the point where I can demonstrate the system
lockup when I attempt to "upgrade".
> I do not have a Netra handy (but I have one in storage, like everyone
> ;p ). I have an Ultra 5 here so UltraSparc IIi CPU. It does not
> expect this behavior. Any chance the memory module need to be
> reseated?
As we see in the POST output the ECC memory is healthy.
>
> I have unstable the mix but as point of reference….
>
> mgt@xray:~$ uname -a
> Linux xray 5.10.0-3-sparc64 #1 Debian 5.10.13-1 (2021-02-06) sparc64
GNU/Linux
> mgt@xray:~$ cat /etc/debian_version
> bullseye/sid
> mgt@xray:~$ cat /proc/cpuinfo
> cpu : TI UltraSparc IIi (Sabre)
> fpu : UltraSparc IIi integrated FPU
> pmu : ultra12
> prom : OBP 3.31.0 2001/07/25 20:36
> type : sun4u
> ncpus probed : 1
> ncpus active : 1
> D$ parity tl1 : 0
> I$ parity tl1 : 0
> Cpu0ClkTck : 0000000013d92d40
> cpucaps : flush,stbar,swap,muldiv,v9,mul32,div32,v8plus,vis
> MMU Type : Spitfire
> MMU PGSZs : 8K,64K,512K,4MB
>
We are very similar here :
ceres#
ceres# uname -a
Linux ceres 5.10.0-1-sparc64 #1 Debian 5.10.5-1 (2021-01-09) sparc64
GNU/Linux
ceres# cat /etc/debian_version
bullseye/sid
ceres# cat /proc/cpuinfo
cpu : TI UltraSparc IIi (Sabre)
fpu : UltraSparc IIi integrated FPU
pmu : ultra12
prom : OBP 3.10.27 2000/06/22 16:45
type : sun4u
ncpus probed : 1
ncpus active : 1
D$ parity tl1 : 0
I$ parity tl1 : 0
Cpu0ClkTck : 000000001a3a2356
cpucaps : flush,stbar,swap,muldiv,v9,mul32,div32,v8plus,vis
MMU Type : Spitfire
MMU PGSZs : 8K,64K,512K,4MB
ceres#
> root@xray:/home/users/mgt# apt update
> Get:1 http://deb.debian.org/debian-ports sid InRelease [55.3 kB]
> Get:2 http://deb.debian.org/debian-ports unreleased InRelease [56.6 kB]
> Get:3 http://deb.debian.org/debian-ports sid/main all Packages [9,069
kB]
> Get:4 http://deb.debian.org/debian-ports sid/main sparc64 Packages
[21.5 MB]
> Fetched 30.7 MB in 1min 55s (266 kB/s)
> Reading package lists... Done
> Building dependency tree... Done
> Reading state information... Done
> 111 packages can be upgraded. Run 'apt list --upgradable' to see them.
> root@xray:/home/users/mgt# apt list --upgradeable
> Listing… Done
> .
> .
>
> apt upgrade was then run and 111 packages upgraded without issue….
>
I wish that I could also see that sort of a result.
I get a total lock up *every* time :
ceres#
ceres# apt update
Get:1 http://deb.debian.org/debian-ports sid InRelease [55.3 kB]
Get:2 http://deb.debian.org/debian-ports sid/main sparc64 Packages [21.5 MB]
Get:3 http://deb.debian.org/debian-ports sid/main all Packages [9069 kB]
Fetched 30.7 MB in 1min 32s (335 kB/s)
Reading package lists... Done
Building dependency tree
Reading state information... Done
176 packages can be upgraded. Run 'apt list --upgradable' to see them.
ceres#
ceres# apt upgrade
E: dpkg was interrupted, you must manually run 'dpkg --configure -a' to
correct the problem.
ceres#
ceres#
ceres# dpkg --configure -a
Setting up perl-modules-5.32 (5.32.1-2) ...
Setting up systemd (247.3-1) ...
[ 1461.972071] systemd[1]: systemd 247.3-1 running in system mode. (+PAM
+AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP
+GCRYPT +GNUTLS +ACL +XZ +LZ4 +ZSTD -SECCOMP +BLKID +ELFUTILS +KMOD
+IDN2 -IDN +PCRE2 default-hierarchy=unified)
[ 1462.267197] systemd[1]: Detected architecture sparc64.
[ 1486.944128] watchdog: BUG: soft lockup - CPU#0 stuck for 22s! [systemd:1]
[ 1487.033443] Modules linked in: drm(E) drm_panel_orientation_quirks(E)
i2c_core(E) sg(E) envctrl(E) display7seg(E) flash(E) fuse(E) configfs(E)
ip_tables(E) x_tables(E) autofs4(E) ext4(E) crc16(E) mbcache(E) jbd2(E)
crc32c_generic(E) sd_mod(E) t10_pi(E) crc_t10dif(E) crct10dif_generic(E)
crct10dif_common(E) ata_generic(E) pata_cmd64x(E) libata(E) sym53c8xx(E)
scsi_transport_spi(E) scsi_mod(E) sunhme(E)
[ 1487.501587] CPU: 0 PID: 1 Comm: systemd Tainted: G E
5.10.0-1-sparc64 #1 Debian 5.10.5-1
[ 1487.625180] TSTATE: 0000000011001604 TPC: 000000000094c4ec TNPC:
000000000094c4f0 Y: 00000000 Tainted: G E
[ 1487.772853] TPC: <misc_open+0x4c/0x180>
[ 1487.823247] g0: fffff800065a1140 g1: 000000001000a830 g2:
0000000000000000 g3: 0000000000000002
[ 1487.937628] g4: fffff80004193c60 g5: 0000000000dcb214 g6:
fffff80004198000 g7: 0000000000500008
[ 1488.052108] o0: 0000000000f24960 o1: fffff800044f1010 o2:
0000000000040000 o3: 0000000000000000
[ 1488.166609] o4: 0000000000000000 o5: 0000000000000000 sp:
fffff8000419af81 ret_pc: 000000000094c4c0
[ 1488.285655] RPC: <misc_open+0x20/0x180>
[ 1488.336074] l0: 0000000000f24800 l1: fffff800041cb021 l2:
00000003936449cb l3: 00000003936449cb
[ 1488.450559] l4: 0000000000020000 l5: fffff8000419b8f0 l6:
0000000000e12000 l7: 0000000000000001
[ 1488.565040] i0: fffff8000adf7840 i1: fffff800044f1000 i2:
0000000000f24800 i3: 0000000000f24978
[ 1488.679518] i4: 00000000000000eb i5: 000000001000a818 i6:
fffff8000419b031 i7: 0000000000665838
[ 1488.794016] I7: <chrdev_open+0x98/0x1e0>
[ 1488.845557] Call Trace:
[ 1488.877596] [<0000000000665838>] chrdev_open+0x98/0x1e0
[ 1488.946340] [<000000000065ae30>] do_dentry_open+0x170/0x420
[ 1489.019626] [<000000000065ca68>] vfs_open+0x28/0x40
[ 1489.083791] [<0000000000671348>] path_openat+0x988/0x1100
[ 1489.154806] [<0000000000673dd0>] do_filp_open+0x50/0x100
[ 1489.224673] [<000000000065cd30>] do_sys_openat2+0x70/0x180
[ 1489.296831] [<000000000065d268>] sys_openat+0x48/0xc0
[ 1489.363285] [<0000000000406174>] linux_sparc_syscall+0x34/0x44
~
Type 'go' to resume
ok
That always happens. Always.
OKay, also you said :
> The Netra’s have few different devices wonder if there is a bug in
> one of those drivers?
Good question. The same MAC address on both of the hme interfaces is
strange. I can check the firmware and see what it says :
ok cd /pci@1f,0/pci@1,1/
ok ls
f0096138 network@3,1
f00902bc scsi@2
f00885f4 network@1,1
f006b270 ebus@1
ok cd network@1,1
ok .properties
local-mac-address 08 00 20 c2 46 48
assigned-addresses 82010910 00000000 e0000000 00000000 00007020
hm-rev 000000c1
device_type network
interrupts 00000001
address-bits 00000030
max-frame-size 00004000
reg 00010900 00000000 00000000 00000000 00000000
02010910 00000000 00000000 00000000 00007020
compatible SUNW,hme
name network
fast-back-to-back
devsel-speed 00000001
class-code 00020000
max-latency 00000005
min-grant 0000000a
revision-id 00000001
device-id 00001001
vendor-id 0000108e
ok
ok cd ..
ok cd network@3,1
ok .properties
local-mac-address 08 00 20 c2 46 49
assigned-addresses 82011910 00000000 e0010000 00000000 00007020
hm-rev 000000c1
device_type network
address-bits 00000030
max-frame-size 00004000
reg 00011900 00000000 00000000 00000000 00000000
02011910 00000000 00000000 00000000 00007020
compatible SUNW,hme
name network
fast-back-to-back
devsel-speed 00000001
class-code 00020000
interrupts 00000001
max-latency 00000005
min-grant 0000000a
revision-id 00000001
device-id 00001001
vendor-id 0000108e
ok
That says the hardware is fine. However we know the MAC addresses are
wrong from the output of "ip link show" as seen above. Very hard for
me to believe that the old old happy meal driver hme is borked.
I will install a scsi card which also has network and see what happens.
--
Dennis Clarke
RISC-V/SPARC/PPC/ARM/CISC
UNIX and Linux spoken
GreyBeard and suspenders optional
Reply to: