14.01.2014 17:00, Andrei Lomov пишет:
удалите все без коментов и сделайтеЧто-то не могу итерфейс поднять на 2-й сетевой карте ... То ли карта того ... Гляньте, пожалуйста, свежим взглядом: # cat /etc/network/interfaces # The loopback network interface auto lo iface lo inet loopback # The primary network interface allow-hotplug eth0 iface eth0 inet static address 192.168.72.41 netmask 255.255.224.0 network 192.168.64.0 broadcast 192.168.95.255 gateway 192.168.64.1 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 217.117.80.1 # The secondary network interface allow-hotplug eth1 iface eth1 inet static address 192.168.1.11 #192.168.0.11 netmask 255.255.255.0 network 192.168.1.0 broadcast 192.168.1.255 gateway 192.168.1.11 # dns-* options are implemented by the resolvconf package, if installed dns-nameservers 217.117.80.1 Карты физически как-бы подключены: # lspci 00:00.0 Host bridge: Intel Corporation 4 Series Chipset DRAM Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 4 Series Chipset PCI Express Root Port (rev 03) 00:1a.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #4 00:1a.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #5 00:1a.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #6 00:1a.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #2 00:1b.0 Audio device: Intel Corporation 82801JI (ICH10 Family) HD Audio Controller 00:1c.0 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 1 00:1c.1 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Port 2 00:1c.5 PCI bridge: Intel Corporation 82801JI (ICH10 Family) PCI Express Root Port 6 00:1d.0 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #1 00:1d.1 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #2 00:1d.2 USB controller: Intel Corporation 82801JI (ICH10 Family) USB UHCI Controller #3 00:1d.7 USB controller: Intel Corporation 82801JI (ICH10 Family) USB2 EHCI Controller #1 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev 90) 00:1f.0 ISA bridge: Intel Corporation 82801JIR (ICH10R) LPC Interface Controller 00:1f.2 IDE interface: Intel Corporation 82801JI (ICH10 Family) 4 port SATA IDE Controller #1 00:1f.3 SMBus: Intel Corporation 82801JI (ICH10 Family) SMBus Controller 00:1f.5 IDE interface: Intel Corporation 82801JI (ICH10 Family) 2 port SATA IDE Controller #2 01:00.0 VGA compatible controller: NVIDIA Corporation G98 [GeForce 8400 GS] (rev a1) 02:00.0 SATA controller: JMicron Technology Corp. JMB363 SATA/IDE Controller (rev 03) 02:00.1 IDE interface: JMicron Technology Corp. JMB363 SATA/IDE Controller (rev 03) 04:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 02) 05:00.0 Ethernet controller: VIA Technologies, Inc. VT6105/VT6106S [Rhine- III] (rev 86) # cat /var/log/dmesg|grep eth [ 1.258541] r8169 0000:04:00.0: eth0: RTL8168c/8111c at 0xf8210000, 00:21:85:5a:bd:1f, XID 1c4000c0 IRQ 44 [ 1.258543] r8169 0000:04:00.0: eth0: jumbo features [frames: 6128 bytes, tx checksumming: ko] [ 1.258870] via-rhine 0000:05:00.0: eth1: VIA Rhine III at 0x1e800, 00:05:5d:81:2d:66, IRQ 16 [ 1.259591] via-rhine 0000:05:00.0: eth1: MII PHY found at address 1, status 0x786d advertising 05e1 Link 45e1 [ 8.935330] r8169 0000:04:00.0: eth0: link down [ 8.935335] r8169 0000:04:00.0: eth0: link down [ 8.935478] ADDRCONF(NETDEV_UP): eth0: link is not ready # cat /etc/udev/rules.d/70-persistent-net.rules # This file was automatically generated by the /lib/udev/write_net_rules # program, run by the persistent-net-generator.rules rules file. # # You can modify it, as long as you keep each rule on a single # line, and change only the value of the NAME= key. # PCI device 0x10ec:/sys/devices/pci0000:00/0000:00:1c.5/0000:04:00.0 (r8169) SUBSYSTEM=="net", ACTION="" DRIVERS=="?*", ATTR{address}=="00:21:85:5a:bd:1f", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth0" # PCI device 0x1106:/sys/devices/pci0000:00/0000:00:1e.0/0000:05:00.0 (via- rhine) SUBSYSTEM=="net", ACTION="" DRIVERS=="?*", ATTR{address}=="00:05:5d:81:2d:66", ATTR{dev_id}=="0x0", ATTR{type}=="1", KERNEL=="eth*", NAME="eth1" udevadm trigger --action=""> проверьте после перезагрузки появилась ли карта. вообще покажите после ребута ip link ip a У меня была похожая трабла дело оказалось в том, что карты гавеные хоть и самые распростарненные на realtek 8139 как их ядро определяло, но увы не работали нормально вместе.Интерфейса на второй карте нет: # ifconfig eth0 Link encap:Ethernet HWaddr 00:21:85:5a:bd:1f inet addr:192.168.72.41 Bcast:192.168.95.255 Mask:255.255.224.0 inet6 addr: fe80::221:85ff:fe5a:bd1f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:668 errors:0 dropped:5 overruns:0 frame:0 TX packets:138 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:57844 (56.4 KiB) TX bytes:22380 (21.8 KiB) Interrupt:44 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:119 errors:0 dropped:0 overruns:0 frame:0 TX packets:119 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:9495 (9.2 KiB) TX bytes:9495 (9.2 KiB) Первая карта смотрит к провайдеру (работает), вторую хотел развернуть во внутреннюю сеть, пока маршрутизатора нет под рукой. Простейшая задача, а не могу понять, где затык. (debian wheezy) Пришлось остановиться на бюджетных Dlink 528TX Кажется. Гигабитных -- -- Faithfully yours, Vladimir Skubriev |