Re: двухмониторная конфигурация
Упс.
Во-первых, монитор 22".
Во-вторых,
~~~~
1)~% dmesg |gr drm
[ 1.625102] [drm] Initialized drm 1.1.0 20060810
[ 1.733857] [drm] set up 7M of stolen space
[ 1.838234] [drm] initialized overlay support
[ 2.354978] [drm:edid_is_valid] *ERROR* EDID checksum is invalid,
remainder is 233
[ 2.355052] [drm:edid_is_valid] *ERROR* Raw EDID:
[ 2.528233] fb0: inteldrmfb frame buffer device
[ 2.528252] [drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on
minor 0
~~~~
Это привеломеня к тому, что вероятно такой бок как раз по причине ошибке
при чтении EDID, потому далее:
~~~~
parse-edid: parse-edid version 2.0.0
get-edid: get-edid version 2.0.0
Performing real mode VBE call
Interrupt 0x10 ax=0x4f00 bx=0x0 cx=0x0
Function supported
Call successful
VBE version 300
VBE string at 0x2110 "Intel(r) 82945GM Chipset Family Graphics
Chip Accelerated VGA BIOS"
VBE/DDC service about to be called
Report DDC capabilities
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x0 cx=0x0
Function supported
Call successful
Monitor and video card combination does not support DDC1 transfers
Monitor and video card combination supports DDC2 transfers
0 seconds per 128 byte EDID block transfer
Screen is not blanked during DDC transfer
Reading next EDID block
VBE/DDC service about to be called
Read EDID
Performing real mode VBE call
Interrupt 0x10 ax=0x4f15 bx=0x1 cx=0x0
Function supported
Call successful
parse-edid: EDID checksum passed.
# EDID version 1 revision 3
Section "Monitor"
# Block type: 2:0 3:ff
# Block type: 2:0 3:fd
# Block type: 2:0 3:fc
Identifier "BenQ V2200Eco"
VendorName "BNQ"
ModelName "BenQ V2200Eco"
# Block type: 2:0 3:ff
# Block type: 2:0 3:fd
HorizSync 24-83
VertRefresh 50-76
# Max dot clock (video bandwidth) 200 MHz
# Block type: 2:0 3:fc
# DPMS capabilities: Active off:yes Suspend:no Standby:no
Mode "1920x1080" # vfreq 60.000Hz, hfreq 67.500kHz
DotClock 148.500000
HTimings 1920 2008 2052 2200
VTimings 1080 1084 1089 1125
Flags "+HSync" "+VSync"
EndMode
# Block type: 2:0 3:ff
# Block type: 2:0 3:fd
# Block type: 2:0 3:fc
EndSection
~~~~
Вобщем причиной может быть плохой кабель, чтож может, но тогда они либо
они у меня все плохие либо что-то тут не так. Надо отметить, что на моей
памяти, правильная конфигурация отвалилась сразу после обновления, точнее
поселе прихода обновлений ядра.
Так, что у меня еще есть надежда :), жду советов.
--
WBR Lavruschenko Oleksandr,
graduate student, Aerospace Department,
National Technical University of Ukraine "Kiev Polytechnic Institute"
web: http://pskla.kpi.ua/staff/lavrushchenko
Reply to: