Re: i845pe
В сообщении от 2 Июнь 2003 12:50 Tim Tereschenko написал:
> On Sun, 1 Jun 2003 01:39:21 +0400
> devi <unxlist@yandex.ru> wrote:
>
> D> есть машины на asus p4pe (i845pe).
> D> очень хочется включить udma5.
> D> к моему сожалению в 2.4.18 ничего
> D> не нашел на предмет i845pe.
> D>
> D> никак не могу найти нужную информацию,
> D> плз, подскажите стоит ли вообще искать,
> D> и если да, то где хотя бы почитать...
> D>
> D> всего наилучшего!
> Поставь 2.4.20 ядро. Там уже есть.
> У меня тоже мать на i845pe.
а можно поподнобнее? --- какие опции нужно сказать ядру при копиляции,
а то я тут разжился мамой на i845pe от Gigabyte GA-8PE800
ядро 2.4.20 --- тормоза страшенные :-(
Вот кусок лога загрузки ядра, посвященный ide:
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
ICH4: detected chipset, but driver not compiled in!
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: BIOS setup was incomplete.
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: QUANTUM FIREBALLP AS40.0, ATA DISK drive
hdc: ATAPI-CD ROM-DRIVE-52MAX, ATAPI CD/DVD-ROM drive
hdd: QUANTUM FIREBALLP AS40.0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 78177792 sectors (40027 MB) w/1902KiB Cache, CHS=4866/255/63
hdd: 78177792 sectors (40027 MB) w/1902KiB Cache, CHS=77557/16/63
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33)
весь вывод dmesg в аттаче. . .
и еще пара вопросов по этой маме
-- есть интегрированный звук --- согласно доке там кодек Realtek ALC650 ---
как его задействовать?
-- как мерить температуру проца итдитп ?
может у кого уже есть готовые рения для такой же мамы?
Linux version 2.4.20-airgate-p4-1 (root@(none)) (gcc version 2.95.4 20011002 (Debian prerelease)) #1 Втр Июн 10 16:05:14 YEKST 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f4b20
hm, page 000f4000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 131056
zone(0): 4096 pages.
zone(1): 126960 pages.
zone(2): 0 pages.
ACPI: Searched entire block, no RSDP was found.
ACPI: RSDP located at physical address c00f6610
RSD PTR v0 [GBT ]
__va_range(0x1fff3000, 0x68): idx=8 mapped at ffff6000
ACPI table found: RSDT v1 [GBT AWRDACPI 16944.11825]
__va_range(0x1fff3040, 0x24): idx=8 mapped at ffff6000
__va_range(0x1fff3040, 0x74): idx=8 mapped at ffff6000
ACPI table found: FACP v1 [GBT AWRDACPI 16944.11825]
__va_range(0x1fff6740, 0x24): idx=8 mapped at ffff6000
__va_range(0x1fff6740, 0x68): idx=8 mapped at ffff6000
ACPI table found: APIC v1 [GBT AWRDACPI 16944.11825]
__va_range(0x1fff6740, 0x68): idx=8 mapped at ffff6000
LAPIC (acpi_id[0x0000] id[0x0] enabled[1])
CPU 0 (0x0000) enabledProcessor #0 Unknown CPU [15:1] APIC version 16
LAPIC (acpi_id[0x0001] id[0x1] enabled[0])
CPU 1 (0x0100) disabled
IOAPIC (id[0x2] address[0xfec00000] global_irq_base[0x0])
INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x1] trigger[0x3])
LAPIC_NMI (acpi_id[0x0000] polarity[0x0] trigger[0x0] lint[0x1])
LAPIC_NMI (acpi_id[0x0001] polarity[0x0] trigger[0x0] lint[0x1])
2 CPUs total
Local APIC address fee00000
Enabling the CPU's according to the ACPI table
Intel MultiProcessor Specification v1.4
Virtual Wire compatibility mode.
OEM ID: OEM00000 Product ID: PROD00000000 APIC at: 0xFEE00000
I/O APIC #2 Version 17 at 0xFEC00000.
Processors: 1
Kernel command line: auto BOOT_IMAGE=Linux ro root=304 mem=nopentium
Initializing CPU#0
Detected 1716.931 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3420.97 BogoMIPS
Memory: 515288k/524224k available (1429k kernel code, 8548k reserved, 575k data, 88k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes)
Inode cache hash table entries: 32768 (order: 6, 262144 bytes)
Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
Buffer-cache hash table entries: 32768 (order: 5, 131072 bytes)
Page-cache hash table entries: 131072 (order: 7, 524288 bytes)
CPU: L1 I cache: 0K, L1 D cache: 8K
CPU: L2 cache: 256K
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: 3febfbf7 00000000 00000000 00000000
CPU: Common caps: 3febfbf7 00000000 00000000 00000000
CPU: Intel(R) Pentium(R) 4 CPU 1.70GHz stepping 03
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
Setting 2 in the phys_id_present_map
...changing IO-APIC physical APIC ID to 2 ... ok.
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-5, 2-6, 2-9, 2-11, 2-20, 2-21 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 21.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02
.... register #01: 00178020
....... : max redirection entries: 0017
....... : PRQ implemented: 1
....... : IO APIC version: 0020
.... register #02: 00000000
....... : arbitration: 00
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00
01 001 01 0 0 0 0 0 1 1 39
02 001 01 0 0 0 0 0 1 1 31
03 001 01 0 0 0 0 0 1 1 41
04 001 01 0 0 0 0 0 1 1 49
05 000 00 1 0 0 0 0 0 0 00
06 000 00 1 0 0 0 0 0 0 00
07 001 01 0 0 0 0 0 1 1 51
08 001 01 0 0 0 0 0 1 1 59
09 000 00 1 0 0 0 0 0 0 00
0a 001 01 0 0 0 0 0 1 1 61
0b 000 00 1 0 0 0 0 0 0 00
0c 001 01 0 0 0 0 0 1 1 69
0d 001 01 0 0 0 0 0 1 1 71
0e 001 01 0 0 0 0 0 1 1 79
0f 001 01 0 0 0 0 0 1 1 81
10 001 01 1 1 0 1 0 1 1 89
11 001 01 1 1 0 1 0 1 1 91
12 001 01 1 1 0 1 0 1 1 99
13 001 01 1 1 0 1 0 1 1 A1
14 000 00 1 0 0 0 0 0 0 00
15 000 00 1 0 0 0 0 0 0 00
16 001 01 1 1 0 1 0 1 1 A9
17 001 01 1 1 0 1 0 1 1 B1
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ10 -> 0:10
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
IRQ16 -> 0:16
IRQ17 -> 0:17
IRQ18 -> 0:18
IRQ19 -> 0:19
IRQ22 -> 0:22
IRQ23 -> 0:23
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1717.0261 MHz.
..... host bus clock speed is 101.0014 MHz.
cpu: 0, clocks: 1010014, slice: 505007
CPU0<T0:1010000,T1:504992,D:1,S:505007,C:1010014>
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfa160, last bus=2
PCI: Using configuration type 1
PCI: Probing PCI hardware
Transparent bridge - Intel Corp. 82801BA/CA/DB PCI Bridge
PCI: Using IRQ router PIIX [8086/24c0] at 00:1f.0
PCI->APIC IRQ transform: (B0,I29,P0) -> 16
PCI->APIC IRQ transform: (B0,I29,P1) -> 19
PCI->APIC IRQ transform: (B0,I29,P2) -> 18
PCI->APIC IRQ transform: (B0,I29,P3) -> 23
PCI->APIC IRQ transform: (B0,I31,P0) -> 16
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B0,I31,P1) -> 17
PCI->APIC IRQ transform: (B1,I0,P0) -> 16
PCI->APIC IRQ transform: (B2,I2,P0) -> 22
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
VFS: Diskquotas version dquot_6.4.0 initialized
Journalled Block Device driver loaded
devfs: v1.12c (20020818) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
ACPI: Core Subsystem version [20011018]
ACPI: Subsystem enabled
ACPI: System firmware supports S0 S1 S4 S5
Processor[0]: C0 C1
Processor[1]: C0 C1
parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE]
parport0: irq 7 detected
parport0: faking semi-colon
parport0: Printer, Hewlett-Packard HP LaserJet 1100
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI enabled
ttyS00 at 0x03f8 (irq = 4) is a 16550A
ttyS01 at 0x02f8 (irq = 3) is a 16550A
lp0: using parport0 (polling).
Real Time Clock Driver v1.10e
i810_rng: RNG not detected
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH4: IDE controller on PCI bus 00 dev f9
ICH4: detected chipset, but driver not compiled in!
PCI: Device 00:1f.1 not available because of resource collisions
ICH4: BIOS setup was incomplete.
ICH4: chipset revision 2
ICH4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA
hda: QUANTUM FIREBALLP AS40.0, ATA DISK drive
hdc: ATAPI-CD ROM-DRIVE-52MAX, ATAPI CD/DVD-ROM drive
hdd: QUANTUM FIREBALLP AS40.0, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 78177792 sectors (40027 MB) w/1902KiB Cache, CHS=4866/255/63
hdd: 78177792 sectors (40027 MB) w/1902KiB Cache, CHS=77557/16/63
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, UDMA(33)
Uniform CD-ROM driver Revision: 3.12
Partition check:
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 < p5 p6 > p4
/dev/ide/host0/bus1/target1/lun0: p1 p2 p3 < p5 p6 p7 p8 p9 p10 p11 >
ne2k-pci.c:v1.02 10/19/2000 D. Becker/P. Gortmaker
http://www.scyld.com/network/ne2k-pci.html
eth0: RealTek RTL-8029 found at 0xc000, IRQ 22, 00:50:BA:57:7F:29.
PPP generic driver version 2.4.2
cmpci: version $Revision: 5.64 $ time 16:06:53 Jun 10 2003
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
uhci.c: USB Universal Host Controller Interface driver v1.1
PCI: Setting latency timer of device 00:1d.0 to 64
uhci.c: USB UHCI at I/O 0xd800, IRQ 16
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.1 to 64
uhci.c: USB UHCI at I/O 0xd000, IRQ 19
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Setting latency timer of device 00:1d.2 to 64
uhci.c: USB UHCI at I/O 0xd400, IRQ 18
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
md: raid0 personality registered as nr 2
md: raid1 personality registered as nr 3
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
[events: 000000cc]
[events: 000000cc]
md: autorun ...
md: considering ide/host0/bus1/target1/lun0/part7 ...
md: adding ide/host0/bus1/target1/lun0/part7 ...
md: adding ide/host0/bus0/target0/lun0/part6 ...
md: created md0
md: bind<ide/host0/bus0/target0/lun0/part6,1>
md: bind<ide/host0/bus1/target1/lun0/part7,2>
md: running: <ide/host0/bus1/target1/lun0/part7><ide/host0/bus0/target0/lun0/part6>
md: ide/host0/bus1/target1/lun0/part7's event counter: 000000cc
md: ide/host0/bus0/target0/lun0/part6's event counter: 000000cc
md: md0: raid array is not clean -- starting background reconstruction
md: RAID level 1 does not need chunksize! Continuing anyway.
md0: max total readahead window set to 124k
md0: 1 data-disks, max readahead per data-disk: 124k
raid1: device ide/host0/bus1/target1/lun0/part7 operational as mirror 1
raid1: device ide/host0/bus0/target0/lun0/part6 operational as mirror 0
raid1: raid set md0 not clean; reconstructing mirrors
raid1: raid set md0 active with 2 out of 2 mirrors
md: updating md0 RAID superblock on device
md: ide/host0/bus1/target1/lun0/part7 [events: 000000cd]<6>(write) ide/host0/bus1/target1/lun0/part7's sb offset: 19534912
md: ide/host0/bus0/target0/lun0/part6 [events: 000000cd]<6>(write) ide/host0/bus0/target0/lun0/part6's sb offset: 19534912
md: syncing RAID array md0
md: minimum _guaranteed_ reconstruction speed: 100 KB/sec/disc.
md: using maximum available idle IO bandwith (but not more than 100000 KB/sec) for reconstruction.
md: using 124k window, over a total of 19534912 blocks.
md: ... autorun DONE.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 32768)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 88k freed
Adding Swap: 738980k swap-space (priority 10)
Adding Swap: 738980k swap-space (priority 10)
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,4), internal journal
reiserfs: checking transaction log (device 03:01) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
reiserfs: checking transaction log (device 03:05) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide1(22,69), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
reiserfs: checking transaction log (device 16:46) ...
Using r5 hash to sort names
ReiserFS version 3.6.25
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on md(9,0), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
svc: unknown version (3)
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
apm: overridden by ACPI.
apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16)
apm: overridden by ACPI.
0: nvidia: loading NVIDIA Linux x86 nvidia.o Kernel Module 1.0-4191 Mon Dec 9 11:49:01 PST 2002
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: Detected Intel i845G chipset
agpgart: AGP aperture is 128M @ 0xd0000000
Reply to:
- Follow-Ups:
- Re: i845pe
- From: Vlad Harchev <hvv@hippo.ru>
- Re: i845pe
- From: Tim Tereschenko <tim@han.ks.ua>
- Re: i845pe
- From: "Dimitry N. Naldaev" <dima@tik.perm.ru>