Lombard booting Debian Ports 2020-04-19 (was Re: Updated installation images for Debian Ports 2020-04-19)
On 4/19/20 11:58 PM, John Paul Adrian Glaubitz wrote:
> ...
> Some error messages would be nice. What's preventing the boot?
I don't know what's preventing the CD from booting. I don't see any
error messages; the CD just doesn't seem to be a bootable device. The
Debian 7.8 CD does boot.
> Did you try loading GRUB directly from the OpenFirmware prompt?
>From the Open Firmware prompt, the Debian 7.8 CD can be booted using the
following command:
0 > boot cd:,\install\yaboot
>From the Open Firmware prompt, the Debian SID CD can't be booted; I
tried these commands:
0 > boot cd:,\boot\grub\powerpc.elf
MAC-PARTS: can't find a default partition
can't OPEN: cd:,\boot\grub\powerpc.elf
0 > boot cd:,\install\vmlinux
MAC-PARTS: can't find a default partition
can't OPEN: cd:,\install\vmlinux
0 > boot cd:,\install\initrd.gz
MAC-PARTS: can't find a default partition
can't OPEN: cd:,\install\initrd.gz
Perhaps I'm not booting the right file?
>
>> I was able to re-install Debian 7.8 from CD; here are the ofpath and
>> ofpathname results for the internal disk (/dev/sda). Hopefully this
>> will be helpful in getting grub to work on this system (if it isn't
>> possible to get grub to work, then I can continue to use yaboot). I
>> could also re-install Debian SID from one of the pre-GRUB versions if
>> you need to see the ofpath and ofpathname results from there.
>>
>> root@lombard:~# df /
>> Filesystem 1K-blocks Used Available Use% Mounted on
>> /dev/sda8 8256952 1050344 6787180 14% /
>>
>> root@lombard:~# ofpath /dev/sda8
>> /pci@80000000/mac-io@10/ata-3@20000/@0:8
>>
>> root@lombard:~# ofpath /dev/sda
>> /pci@80000000/mac-io@10/ata-3@20000/@0
>>
>> root@lombard:~# ofpathname /dev/sda8
>> /pci@80000000/mac-io@10/ata-3@20000/scsi@0/sd@0,0
>>
>> root@lombard:~# ofpathname /dev/sda
>> /pci@80000000/mac-io@10/ata-3@20000/scsi@0/sd@0,0
>
> This doesn't look like you are using the updated ofpathname version I
> created but rather an outdated one.
Yes, ofpath and ofpathname are the outdated versions from Debian 7.8.
>
> Is that by any chance the version of ofpathname shipped in Debian
> Jessie? If yes, it's not surprising that the paths reported are
> not correct.
It's from Debian 7.8 (Wheezy). I only included the paths in case the
information would be useful. I can re-install Debian SID from a
pre-GRUB Debian SID CD and install your later versions of ofpathame if
that would be helpful.
> ...
> Also, in order to fix potential issues with your particular
> model, I need the output of "cat /proc/cpuinfo", "dmesg",
> "lsscsi -tv" and "lspci".
>
> Thanks,
> Adrian
>
The requested information is below (unfortunately, at this point it's
all from Debian 7.8):
-----
root@lombard:/# cat /proc/cpuinfo
processor : 0
cpu : 740/750
temperature : 46-49 C (uncalibrated)
clock : 399.999996MHz
revision : 130.2 (pvr 0008 8202)
bogomips : 33.40
timebase : 16703983
platform : PowerMac
model : PowerBook1,1
machine : PowerBook1,1
motherboard : PowerBook1,1 MacRISC Power Macintosh
detected as : 64 (PowerBook 101 (Lombard))
pmac flags : 00000009
L2 cache : 1024K unified
pmac-generation : NewWorld
Memory : 512 MB
root@lombard:/#
root@lombard:/# lsscsi --version
version: 0.26 2012/01/31 [svn: r97]
root@lombard:/# lsscsi -tv
[0:0:0:0] disk ata: /dev/sda
dir: /sys/bus/scsi/devices/0:0:0:0
[/sys/devices/pci0000:00/0000:00:10.0/0.80800000:mac-io/0.00020000:ata-3/host0/target0:0:0/0:0:0:0]
[1:0:0:0] cd/dvd ata: /dev/sr0
dir: /sys/bus/scsi/devices/1:0:0:0
[/sys/devices/pci0000:00/0000:00:10.0/0.80800000:mac-io/0.00000034:media-ba/0.00021000:ata-3/host1/target1:0:0/1:0:0:0]
root@lombard:/#
root@lombard:/# lspci --version
lspci version 3.1.9
root@lombard:/# lspci
00:00.0 Host bridge: Motorola MPC106 [Grackle] (rev 40)
00:0e.0 USB controller: LSI Corporation USB (rev 12)
00:0f.0 Multimedia controller: C-Cube Microsystems Cinemaster C 3.0 DVD
Decoder (rev 02)
00:10.0 Unassigned class [ff00]: Apple Inc. Paddington Mac I/O
00:11.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI
3D Rage LT Pro (rev dc)
00:13.0 CardBus bridge: Texas Instruments PCI1211
root@lombard:/#
root@lombard:/# dmesg
[ 0.000000] Using PowerMac machine description
[ 0.000000] Cannot reserve gpages without hugetlb enabled
[ 0.000000] Total memory = 512MB; using 1024kB for hash table (at
cff00000)
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Linux version 3.2.0-4-powerpc
(debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-14) )
#1 Debian 3.2.78-1
[ 0.000000] Found initrd at 0xc1400000:0xc1e6b000
[ 0.000000] Found a Paddington mac-io controller, rev: 0, mapped at
0xff780000
[ 0.000000] PowerMac motherboard: PowerBook 101 (Lombard)
[ 0.000000] PMU driver v2 initialized for 1999 PowerBook G3, firmware: 0b
[ 0.000000] bootconsole [udbg0] enabled
[ 0.000000] Found Grackle (MPC106) PCI host bridge at
0x0000000080000000. Firmware bus number: 0->0
[ 0.000000] PCI host bridge /pci@80000000 (primary) ranges:
[ 0.000000] IO 0x00000000fe000000..0x00000000fe7fffff ->
0x0000000000000000
[ 0.000000] MEM 0x00000000fd000000..0x00000000fdffffff ->
0x0000000000000000
[ 0.000000] MEM 0x0000000080000000..0x00000000fcffffff ->
0x0000000080000000
[ 0.000000] Removing ISA hole at 0x00000000fd000000
[ 0.000000] nvram: OF partition at 0x140
[ 0.000000] nvram: XP partition at 0x11b0
[ 0.000000] nvram: NR partition at 0x12b0
[ 0.000000] Top of RAM: 0x20000000, Total RAM: 0x20000000
[ 0.000000] Memory hole size: 0MB
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0x00000000 -> 0x00020000
[ 0.000000] Normal empty
[ 0.000000] HighMem empty
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0x00000000 -> 0x00020000
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c055dd10, node_mem_map
c06ec000
[ 0.000000] DMA zone: 1024 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 130048 pages, LIFO batch:31
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on.
Total pages: 130048
[ 0.000000] Kernel command line: root=/dev/sda8 ro
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144
bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072
bytes)
[ 0.000000] High memory: 0k
[ 0.000000] Memory: 500656k/524288k available (5232k kernel code,
23632k reserved, 320k data, 1512k bss, 244k init)
[ 0.000000] Kernel virtual memory layout:
[ 0.000000] * 0xfffcf000..0xfffff000 : fixmap
[ 0.000000] * 0xff800000..0xffc00000 : highmem PTEs
[ 0.000000] * 0xfeebb000..0xff800000 : early ioremap
[ 0.000000] * 0xe1000000..0xfeebb000 : vmalloc & ioremap
[ 0.000000] NR_IRQS:512
[ 0.000000] irq: Found primary Apple PIC /pci@80000000/mac-io@10 for
64 irqs
[ 0.000000] irq: System has 64 possible interrupts
[ 0.000000] GMT Delta read from XPRAM: -360 minutes, DST: on
[ 0.000000] time_init: decrementer frequency = 16.703983 MHz
[ 0.000000] time_init: processor frequency = 399.999996 MHz
[ 0.000000] clocksource: timebase mult[ef76be9] shift[22] registered
[ 0.000000] clockevent: decrementer mult[446b654] shift[32] cpu[0]
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled, bootconsole disabled
[ 0.000000] pmac_zilog: serial modem detected
[ 0.002444] pid_max: default: 32768 minimum: 301
[ 0.002648] Security Framework initialized
[ 0.002709] AppArmor: AppArmor disabled by boot time parameter
[ 0.002779] Mount-cache hash table entries: 512
[ 0.003475] device-tree: Duplicate name in /cpus/PowerPC,750@0,
renamed to "l2-cache#1"
[ 0.006163] Initializing cgroup subsys cpuacct
[ 0.006216] Initializing cgroup subsys memory
[ 0.006285] Initializing cgroup subsys devices
[ 0.006308] Initializing cgroup subsys freezer
[ 0.006330] Initializing cgroup subsys net_cls
[ 0.006352] Initializing cgroup subsys blkio
[ 0.006395] Initializing cgroup subsys perf_event
[ 0.008951] devtmpfs: initialized
[ 0.010516] print_constraints: dummy:
[ 0.010854] NET: Registered protocol family 16
[ 0.012275] PMU i2c /pci@80000000/mac-io@10/via-pmu@16000
[ 0.012314] channel 1 bus <multibus>
[ 0.012338] channel 2 bus <multibus>
[ 0.012844] PCI: Probing PCI hardware
[ 0.013127] pci 0000:00:00.0: [1057:0002] type 0 class 0x000600
[ 0.013274] pci 0000:00:0e.0: [11c1:5801] type 0 class 0x000c03
[ 0.013310] pci 0000:00:0e.0: reg 10: [mem 0x80882000-0x80882fff]
[ 0.013407] pci 0000:00:0f.0: [123f:8888] type 0 class 0x000480
[ 0.013436] pci 0000:00:0f.0: reg 10: [io 0x0c00-0x0cff]
[ 0.013549] pci 0000:00:10.0: [106b:0017] type 0 class 0x00ff00
[ 0.013575] pci 0000:00:10.0: reg 10: [mem 0x80800000-0x8087ffff]
[ 0.013672] pci 0000:00:11.0: [1002:4c49] type 0 class 0x000300
[ 0.013703] pci 0000:00:11.0: reg 10: [mem 0x81000000-0x81ffffff]
[ 0.013726] pci 0000:00:11.0: reg 14: [io 0x0c00-0x0cff]
[ 0.013748] pci 0000:00:11.0: reg 18: [mem 0x80881000-0x80881fff]
[ 0.013790] pci 0000:00:11.0: reg 30: [mem 0x00000000-0x0001ffff pref]
[ 0.013833] pci 0000:00:11.0: supports D1 D2
[ 0.013893] pci 0000:00:13.0: [104c:ac1e] type 2 class 0x000607
[ 0.013923] pci 0000:00:13.0: reg 10: [mem 0x80880000-0x80880fff]
[ 0.013966] pci 0000:00:13.0: supports D1 D2
[ 0.013981] pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot
[ 0.014168] pci 0000:00:13.0: bridge configuration invalid ([bus
00-00]), reconfiguring
[ 0.015309] PCI: Cannot allocate resource region 1 of device
0000:00:11.0, will remap
[ 0.015374] PCI 0000:00 Cannot reserve Legacy IO [io 0x0000-0x0fff]
[ 0.015391] PCI: max bus depth: 1 pci_try_num: 2
[ 0.015447] pci 0000:00:11.0: BAR 6: assigned [mem
0x80000000-0x8001ffff pref]
[ 0.015496] pci 0000:00:11.0: BAR 1: assigned [io 0x1000-0x10ff]
[ 0.015537] pci 0000:00:13.0: BAR 16: assigned [mem
0x84000000-0x87ffffff]
[ 0.015578] pci 0000:00:13.0: BAR 15: assigned [mem
0x88000000-0x8bffffff pref]
[ 0.015624] pci 0000:00:13.0: BAR 14: assigned [io 0x1100-0x11ff]
[ 0.015661] pci 0000:00:13.0: BAR 13: assigned [io 0x1200-0x12ff]
[ 0.015698] pci 0000:00:13.0: CardBus bridge to [bus 01-04]
[ 0.015731] pci 0000:00:13.0: bridge window [io 0x1200-0x12ff]
[ 0.015767] pci 0000:00:13.0: bridge window [io 0x1100-0x11ff]
[ 0.015804] pci 0000:00:13.0: bridge window [mem
0x88000000-0x8bffffff pref]
[ 0.015850] pci 0000:00:13.0: bridge window [mem 0x84000000-0x87ffffff]
[ 0.015904] pci 0000:00:13.0: enabling device (0000 -> 0003)
[ 0.015948] pci_bus 0000:00: resource 0 [io 0x0000-0x7fffff]
[ 0.015965] pci_bus 0000:00: resource 1 [mem 0x80000000-0xfcffffff]
[ 0.015982] pci_bus 0000:01: resource 0 [io 0x1200-0x12ff]
[ 0.015998] pci_bus 0000:01: resource 1 [io 0x1100-0x11ff]
[ 0.016014] pci_bus 0000:01: resource 2 [mem 0x88000000-0x8bffffff pref]
[ 0.016032] pci_bus 0000:01: resource 3 [mem 0x84000000-0x87ffffff]
[ 0.019748] bio: create slab <bio-0> at 0
[ 0.020414] vgaarb: device added:
PCI:0000:00:11.0,decodes=io+mem,owns=mem,locks=none
[ 0.020469] vgaarb: loaded
[ 0.020489] vgaarb: bridge control possible 0000:00:11.0
[ 0.021065] SCSI subsystem initialized
[ 0.021335] libata version 3.00 loaded.
[ 0.022099] Switching to clocksource timebase
[ 0.044122] NET: Registered protocol family 2
[ 0.056341] IP route cache hash table entries: 4096 (order: 2, 16384
bytes)
[ 0.057466] TCP established hash table entries: 16384 (order: 5,
131072 bytes)
[ 0.058600] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.059179] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.059221] TCP reno registered
[ 0.059251] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.059320] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.059821] NET: Registered protocol family 1
[ 0.114276] PCI: CLS 32 bytes, default 32
[ 0.114673] Unpacking initramfs...
[ 1.515954] Freeing initrd memory: 10668k freed
[ 1.519717] Thermal assist unit using timers, shrink_timer: 500 jiffies
[ 1.522226] audit: initializing netlink socket (disabled)
[ 1.522346] type=2000 audit(1587388694.520:1): initialized
[ 1.583081] VFS: Disk quotas dquot_6.5.2
[ 1.583243] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 1.583478] msgmni has been set to 1000
[ 1.584419] alg: No test for stdrng (krng)
[ 1.584604] Block layer SCSI generic (bsg) driver version 0.4 loaded
(major 253)
[ 1.584657] io scheduler noop registered
[ 1.584682] io scheduler deadline registered
[ 1.584745] io scheduler cfq registered (default)
[ 1.585305] atyfb 0000:00:11.0: enabling device (0086 -> 0087)
[ 1.585370] atyfb: using auxiliary register aperture
[ 1.585800] atyfb: 3D RAGE LT PRO (Mach64 LI, PCI) [0x4c49 rev 0xdc]
[ 1.585877] atyfb: 8M SDRAM (1:1), 29.498928 MHz XTAL, 230 MHz PLL,
100 Mhz MCLK, 100 MHz XCLK
[ 1.586472] atyfb: monitor sense=62b, mode 6
[ 1.649857] Console: switching to colour frame buffer device 128x48
[ 1.669346] atyfb: fb0: ATY Mach64 frame buffer device on PCI
[ 1.670592] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 1.672056] pmac_zilog: 0.6 (Benjamin Herrenschmidt
<benh@kernel.crashing.org>)
[ 1.672399] ttyPZ0 at MMIO 0x80813020 (irq = 16) is a Z85c30 ESCC -
Internal modem
[ 1.672978] ttyPZ1 at MMIO 0x80813000 (irq = 17) is a Z85c30 ESCC -
Infrared port
[ 1.673544] Serial: MPC52xx PSC UART driver
[ 1.673921] Generic non-volatile memory driver v1.1
[ 1.674337] Linux agpgart interface v0.103
[ 1.674703] MacIO PCI driver attached to Paddington chipset
[ 1.675865] Can't request resource 0 for MacIO device 0.00000000:power-mg
[ 1.677682] swim3 0.00015000:fdc: [fd0] SWIM3 floppy controller in
media bay
[ 1.679937] mediabay0: Registered Heathrow media-bay
[ 1.882971] PMU Backlight initialized (pmubl)
[ 1.884077] mediabay0: Bay contains an ATA device
[ 1.884311] adb: starting probe task...
[ 2.902181] pata-macio 0.00020000:ata-3: Activating pata-macio
chipset Heathrow ATA, Apple bus ID 0
[ 2.903573] scsi0 : pata_macio
[ 2.904105] ata1: PATA max MWDMA2 irq 25
[ 3.066740] ata1.00: ATA-6: ST9120821A, 3.04, max UDMA/100
[ 3.066980] ata1.00: 234441648 sectors, multi 8: LBA48
[ 3.083325] ata1.00: configured for MWDMA2
[ 3.084193] scsi 0:0:0:0: Direct-Access ATA ST9120821A
3.04 PQ: 0 ANSI: 5
[ 3.922173] pata-macio 0.00021000:ata-3: Activating pata-macio
chipset Heathrow ATA, Apple bus ID 1
[ 3.933485] scsi1 : pata_macio
[ 3.943940] ata2: PATA max MWDMA2 irq 36
[ 3.954713] mousedev: PS/2 mouse device common for all mice
[ 3.968541] rtc-generic rtc-generic: rtc core: registered rtc-generic
as rtc0
[ 3.980041] TCP cubic registered
[ 3.990485] NET: Registered protocol family 10
[ 4.003426] Mobile IPv6
[ 4.013212] NET: Registered protocol family 17
[ 4.023187] Registering the dns_resolver key type
[ 4.033826] PM: Hibernation image not present or could not be loaded.
[ 4.033891] registered taskstats version 1
[ 4.048975] rtc-generic rtc-generic: setting system clock to
2020-04-20 07:18:17 UTC (1587367097)
[ 4.058952] Initializing network drop monitor service
[ 4.114672] ata2.00: ATAPI: MATSHITADVD-ROM SR-8174, C113, max UDMA/33
[ 4.133240] adb devices: [2]: 2 c3
[ 4.139638] ata2.00: configured for MWDMA2
[ 4.149779] [3]: 3 1 [7]: 7 1f
[ 4.164227] scsi 1:0:0:0: CD-ROM MATSHITA DVD-ROM SR-8174
C113 PQ: 0 ANSI: 5
[ 4.177332] Freeing unused kernel memory: 244k freed
[ 4.191444] ADB keyboard at 2, handler 1
[ 4.210307] Detected ADB keyboard, type ANSI.
[ 4.210692] input: ADB keyboard as /devices/virtual/input/input0
[ 4.210999] input: ADB Powerbook buttons as /devices/virtual/input/input1
[ 4.249061] ADB mouse at 3, handler set to 4 (trackpad)
[ 4.326685] input: ADB mouse as /devices/virtual/input/input2
[ 4.345633] adb: finished probe task...
[ 4.377032] udevd[47]: starting version 175
[ 4.546403] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0xe
frozen
[ 4.556564] ata2: mediabay plug
[ 4.566431] ata2: soft resetting link
[ 4.767729] usbcore: registered new interface driver usbfs
[ 5.330217] mesh: configured for synchronous 5 MB/s
[ 5.365246] eth0: BMAC+ at 00:50:e4:45:95:32
[ 5.400865] usbcore: registered new interface driver hub
[ 5.463383] usbcore: registered new device driver usb
[ 5.569085] sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120
GB/111 GiB)
[ 5.593938] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.614732] sd 0:0:0:0: [sda] Write Protect is off
[ 5.624649] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.654329] mesh: performing initial bus reset...
[ 5.668549] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 5.794728] ata2.00: configured for MWDMA2
[ 5.805042] sda: [mac] sda1 sda2 sda3 sda4 sda5 sda6 sda7 sda8 sda9
sda10 sda11 sda12 sda13
[ 5.815498] ata2: EH complete
[ 5.832740] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.850616] sr0: scsi3-mmc drive: 24x/24x cd/rw xa/form2 cdda tray
[ 5.860996] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 5.872886] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.897073] ohci_hcd 0000:00:0e.0: OHCI Host Controller
[ 5.912114] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.924423] sr 1:0:0:0: Attached scsi CD-ROM sr0
[ 5.928653] ohci_hcd 0000:00:0e.0: new USB bus registered, assigned
bus number 1
[ 5.942979] sr 1:0:0:0: Attached scsi generic sg1 type 5
[ 5.974454] ohci_hcd 0000:00:0e.0: irq 28, io mem 0x80882000
[ 6.078416] usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
[ 6.088787] usb usb1: New USB device strings: Mfr=3, Product=2,
SerialNumber=1
[ 6.098982] usb usb1: Product: OHCI Host Controller
[ 6.109156] usb usb1: Manufacturer: Linux 3.2.0-4-powerpc ohci_hcd
[ 6.119389] usb usb1: SerialNumber: 0000:00:0e.0
[ 6.131528] hub 1-0:1.0: USB hub found
[ 6.141808] hub 1-0:1.0: 2 ports detected
[ 9.666257] scsi2 : MESH
[ 9.697317] scsi: waiting for bus probes to complete ...
[ 12.083414] PM: Starting manual resume from disk
[ 12.093365] PM: Hibernation image partition 8:12 present
[ 12.093377] PM: Looking for hibernation image.
[ 12.109762] PM: Image not found (code -22)
[ 12.109777] PM: Hibernation image not present or could not be loaded.
[ 12.218003] kjournald starting. Commit interval 5 seconds
[ 12.228276] EXT3-fs (sda8): mounted filesystem with ordered data mode
[ 15.159163] udevd[273]: starting version 175
[ 16.236102] yenta_cardbus 0000:00:13.0: CardBus bridge found [0000:0000]
[ 16.247256] yenta_cardbus 0000:00:13.0: Enabling burst memory read
transactions
[ 16.258475] yenta_cardbus 0000:00:13.0: Using CSCINT to route CSC
interrupts to PCI
[ 16.269489] yenta_cardbus 0000:00:13.0: Routing CardBus interrupts to PCI
[ 16.280365] yenta_cardbus 0000:00:13.0: TI: mfunc 0x00000002, devctl 0x60
[ 16.297467] PowerMac i2c bus pmu 2 registered
[ 16.446554] PowerMac i2c bus pmu 1 registered
[ 16.566416] yenta_cardbus 0000:00:13.0: ISA IRQ mask 0x0000, PCI irq 22
[ 16.577450] yenta_cardbus 0000:00:13.0: Socket status: 30000086
[ 16.715596] yenta_cardbus 0000:00:13.0: pcmcia: parent PCI bridge
window: [io 0x0000-0x7fffff]
[ 16.814710] yenta_cardbus 0000:00:13.0: pcmcia: parent PCI bridge
window: [mem 0x80000000-0xfcffffff]
[ 16.873784] pcmcia_socket pcmcia_socket0: cs: memory probe
0x80000000-0xfcffffff: excluding 0x80000000-0x81ffffff 0x84000000-0x8bffffff
[ 17.096830] pcmcia_socket pcmcia_socket0: cs: memory probe
0x80000000-0x80ffffff: excluding 0x80000000-0x800fffff 0x80800000-0x808fffff
[ 20.454023] Adding 2097148k swap on /dev/sda12. Priority:-1
extents:1 across:2097148k
[ 21.348654] EXT3-fs (sda8): using internal journal
[ 21.785423] loop: module loaded
[ 23.233212] input: PowerMac Beep as
/devices/pci0000:00/0000:00:10.0/input/input3
[ 29.463986] phy registers:
[ 29.465315] 0800 7849 2000 5c10 01e1 c5e1 000f 2801
[ 29.486742] 0000 0000 0000 0000 0000 0000 0000 0000
[ 29.507808] 2002 0000 0000 0000 0001 0000 0020 0000
[ 29.528585] 0000 0000 0180 0100 0006 0f00 0000 0000
[ 30.170025] RPC: Registered named UNIX socket transport module.
[ 30.180380] RPC: Registered udp transport module.
[ 30.190716] RPC: Registered tcp transport module.
[ 30.200936] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 30.358437] FS-Cache: Loaded
[ 30.693484] FS-Cache: Netfs 'nfs' registered for caching
[ 30.786129] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 37.188955] Bluetooth: Core ver 2.16
[ 37.189407] NET: Registered protocol family 31
[ 37.189633] Bluetooth: HCI device and connection manager initialized
[ 37.189923] Bluetooth: HCI socket layer initialized
[ 37.190205] Bluetooth: L2CAP socket layer initialized
[ 37.192653] Bluetooth: SCO socket layer initialized
[ 37.235697] Bluetooth: RFCOMM TTY layer initialized
[ 37.236140] Bluetooth: RFCOMM socket layer initialized
[ 37.236412] Bluetooth: RFCOMM ver 1.11
[ 37.266282] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 37.266683] Bluetooth: BNEP filters: protocol multicast
[ 37.643225] lp: driver loaded but no devices found
[ 40.210173] eth0: no IPv6 routers present
[ 42.910303] input: Mouseemu virtual keyboard as
/devices/virtual/input/input4
[ 42.918404] input: Mouseemu virtual mouse as
/devices/virtual/input/input5
Reply to: