Re: Qube2 with Squeeze won't boot
On Sat, Dec 15, 2012 at 12:21 AM, Arnaud Patard
<arnaud.patard@rtp-net.org> wrote:
> Sameer Verma <sverma@sfsu.edu> writes:
>
> Hi,
>
>> I just upgraded my Qube2 from Lenny to Squeeze. Went through the
>> process of apt-get update and apt-get upgrade using squeeze in
>> sources.list. After this, I installed the r5k kernel and installed
>> udev (reference
>> http://www.debian.org/releases/stable/amd64/release-notes/ch-upgrading.en.html)
>>
>> A reboot won't bring the machine up.
>>
>> Serial connection gives me the following.
>>
>> Any suggestions?
>>
>> cheers,
>> Sameer
>>
>> [ "CoLo" v1.22 ]
>> stage2: 8bfa0000-8c000000
>> cpu: clock 250.000MHz
>> pci: unit type <Qube2>
>> tulip: #0 device 21143
>> tulip: #1 device 21143
>> tulip: {00:10:e0:00:f8:9a}
>> ide: resetting
>> boot: running boot menu
>> 1> lcd 'Booting...'
>> 1> mount
>> ide: {ST313021A}
>> ide: LBA 25434228
>> ide: supports PIO mode 4
>> ide: mode 4 timing
>> ide: partition 1
>> ext2: revision 0
>> 1> lcd 'Booting...' /dev/{mounted-volume}
>> 1> -load /boot/default.colo
>> ext2: {boot/default.colo} --> {./default.colo}
>> 000000bf 191t
>> 1> -script
>> 2> mount hda1
>> ext2: revision 0
>> 2> load /vmlinux
>> ext2: {vmlinux} --> {vmlinux-2.6.32-5-r5k-cobalt}
>> 00598334 5866292t
>> 2> lcd "Booting Debian"
>> 2> var cons_opts ''
>> 2> -var cons_opts console=ttyS0,{console-speed}
>> 2> execute root=/dev/hda2 {cons_opts}
>
> root=/dev/hda2
>
> [...]
>
>> [ 0.768000] scsi 0:0:0:0: Direct-Access ATA ST313021A
>> 3.03 PQ: 0 ANSI: 5
>> [ 0.780000] TCP cubic registered
>> [ 0.784000] NET: Registered protocol family 17
>> [ 0.792000] registered taskstats version 1
>> [ 0.800000] rtc_cmos rtc_cmos: setting system clock to 2012-12-15
>> 06:34:48 UTC (1355553288)
>> [ 0.808000] Initalizing network drop monitor service
>> [ 0.820000] sd 0:0:0:0: [sda] 25434228 512-byte logical blocks:
>> (13.0 GB/12.1 GiB)
>> [ 0.832000] sd 0:0:0:0: [sda] Write Protect is off
>> [ 0.840000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
>> enabled, doesn't support DPO or FUA
>> [ 0.856000] sda: sda1 sda2 sda3 < sda5 sda6 >
>> [ 0.916000] sd 0:0:0:0: [sda] Attached SCSI disk
>
> /dev/sda1-6 detected
>
> Try updating your bootloader configuration to use root=/dev/sda2 instead
> of root=/dev/hda2 (things have moved from ide drivers to libata drivers).
Thanks. How do I edit the config once it throws me into a boot shell?
I am able to mount /dev/hda1 but don't see any editor. Do I have to
remove the drive and mount it elsewhere and edit?
cheers,
Sameer
>
> Arnaud
>
>
Reply to: