Qube2 with Squeeze won't boot
I just upgraded my Qube2 from Lenny to Squeeze. Went through the
process of apt-get update and apt-get upgrade using squeeze in
sources.list. After this, I installed the r5k kernel and installed
udev (reference
http://www.debian.org/releases/stable/amd64/release-notes/ch-upgrading.en.html)
A reboot won't bring the machine up.
Serial connection gives me the following.
Any suggestions?
cheers,
Sameer
[ "CoLo" v1.22 ]
stage2: 8bfa0000-8c000000
cpu: clock 250.000MHz
pci: unit type <Qube2>
tulip: #0 device 21143
tulip: #1 device 21143
tulip: {00:10:e0:00:f8:9a}
ide: resetting
boot: running boot menu
1> lcd 'Booting...'
1> mount
ide: {ST313021A}
ide: LBA 25434228
ide: supports PIO mode 4
ide: mode 4 timing
ide: partition 1
ext2: revision 0
1> lcd 'Booting...' /dev/{mounted-volume}
1> -load /boot/default.colo
ext2: {boot/default.colo} --> {./default.colo}
000000bf 191t
1> -script
2> mount hda1
ext2: revision 0
2> load /vmlinux
ext2: {vmlinux} --> {vmlinux-2.6.32-5-r5k-cobalt}
00598334 5866292t
2> lcd "Booting Debian"
2> var cons_opts ''
2> -var cons_opts console=ttyS0,{console-speed}
2> execute root=/dev/hda2 {cons_opts}
elf32: 00080000 - 0053d36f (80084280) (ffffffff.80000000)
elf32: 80080000 (80080000) 4500176t + 469152t
[ 0.124000] Cobalt board ID: 5
[ 0.132000] Switching to clocksource MIPS
[ 0.164000] NET: Registered protocol family 2
[ 0.172000] IP route cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.184000] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.192000] TCP bind hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.200000] TCP: Hash tables configured (established 8192 bind 8192)
[ 0.208000] TCP reno registered
[ 0.212000] NET: Registered protocol family 1
[ 0.220000] pci 0000:00:09.0: Activating ISA DMA hang workarounds
[ 0.224000] PCI: Enabling device 0000:00:09.2 (0000 -> 0001)
[ 0.240000] audit: initializing netlink socket (disabled)
[ 0.244000] type=2000 audit(0.246:1): initialized
[ 0.280000] VFS: Disk quotas dquot_6.5.2
[ 0.288000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.300000] msgmni has been set to 370
[ 0.312000] alg: No test for stdrng (krng)
[ 0.316000] Block layer SCSI generic (bsg) driver version 0.4
loaded (major 253)
[ 0.324000] io scheduler noop registered
[ 0.332000] io scheduler anticipatory registered
[ 0.336000] io scheduler deadline registered
[ 0.340000] io scheduler cfq registered (default)
[ 0.400000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
�[ 0.440000] console [ttyS0] enabled, bootconsole disabled 21) is a ST16650V2
[ 0.440000] console [ttyS0] enabled, bootconsole disabled
[ 0.484000] brd: module loaded
[ 0.492000] scsi0 : pata_via
[ 0.496000] scsi1 : pata_via
[ 0.504000] ata1: PATA max UDMA/33 cmd 0x1f0 ctl 0x3f6 bmdma 0x1420 irq 14
[ 0.508000] ata2: PATA max UDMA/33 cmd 0x170 ctl 0x376 bmdma 0x1428 irq 15
[ 0.520000] physmap platform flash device: 00080000 at 1fc00000
[ 0.528000] Found: AMD AM29F040
[ 0.532000] physmap-flash.0: Found 1 x8 devices at 0x0 in 8-bit bank
[ 0.540000] number of JEDEC chips: 1
[ 0.544000] cfi_cmdset_0002: Disabling erase-suspend-program due to
code brokenness.
[ 0.552000] cmdlinepart partition parsing not available
[ 0.560000] RedBoot partition parsing not available
[ 0.564000] Using physmap partition information
[ 0.568000] Creating 1 MTD partitions on "physmap-flash.0":
[ 0.576000] 0x000000000000-0x000000080000 : "firmware"
[ 0.584000] Linux Tulip driver version 1.1.15 (Feb 27, 2007)
[ 0.592000] PCI: Enabling device 0000:00:07.0 (0045 -> 0047)
[ 0.600000] tulip0: Old format EEPROM on 'Cobalt Microserver'
board. Using substitute media control info.
[ 0.612000] tulip0: EEPROM default media type Autosense.
[ 0.616000] tulip0: Index #0 - Media MII (#11) described by a
21142 MII PHY (3) block.
[ 0.628000] tulip0: MII transceiver #1 config 1000 status 7809
advertising 01e1.
[ 0.644000] eth0: Digital DS21142/43 Tulip rev 65 at MMIO
0x12080000, 00:10:e0:00:f8:9a, IRQ 19.
[ 0.652000] PCI: Enabling device 0000:00:0c.0 (0005 -> 0007)
[ 0.664000] tulip1: Old format EEPROM on 'Cobalt Microserver'
board. Using substitute media control info.
[ 0.672000] tulip1: EEPROM default media type Autosense.
[ 0.680000] tulip1: Index #0 - Media MII (#11) described by a
21142 MII PHY (3) block.
[ 0.692000] tulip1: MII transceiver #1 config 1000 status 7809
advertising 01e1.
[ 0.708000] eth1: Digital DS21142/43 Tulip rev 65 at MMIO
0x12080400, 00:10:e0:00:d5:26, IRQ 20.
[ 0.716000] ata1.00: ATA-5: ST313021A, 3.03, max UDMA/66
[ 0.724000] ata1.00: 25434228 sectors, multi 0: LBA
[ 0.732000] mice: PS/2 mouse device common for all mice
[ 0.740000] rtc_cmos rtc_cmos: rtc core: registered rtc_cmos as rtc0
[ 0.748000] rtc0: alarms up to one day, 242 bytes nvram
[ 0.752000] ata1.00: configured for UDMA/33
[ 0.760000] Registered led device: qube::front
[ 0.768000] scsi 0:0:0:0: Direct-Access ATA ST313021A
3.03 PQ: 0 ANSI: 5
[ 0.780000] TCP cubic registered
[ 0.784000] NET: Registered protocol family 17
[ 0.792000] registered taskstats version 1
[ 0.800000] rtc_cmos rtc_cmos: setting system clock to 2012-12-15
06:34:48 UTC (1355553288)
[ 0.808000] Initalizing network drop monitor service
[ 0.820000] sd 0:0:0:0: [sda] 25434228 512-byte logical blocks:
(13.0 GB/12.1 GiB)
[ 0.832000] sd 0:0:0:0: [sda] Write Protect is off
[ 0.840000] sd 0:0:0:0: [sda] Write cache: enabled, read cache:
enabled, doesn't support DPO or FUA
[ 0.856000] sda: sda1 sda2 sda3 < sda5 sda6 >
[ 0.916000] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.492000] VFS: Cannot open root device "hda2" or unknown-block(0,0)
[ 1.500000] Please append a correct "root=" boot option; here are
the available partitions:
[ 1.508000] 0800 12717114 sda driver: sd
[ 1.512000] 0801 96358 sda1
[ 1.516000] 0802 3502170 sda2
[ 1.520000] 0803 1 sda3
[ 1.524000] 0805 345366 sda5
[ 1.528000] 0806 8771458 sda6
[ 1.532000] Kernel panic - not syncing: VFS: Unable to mount root
fs on unknown-block(0,0)
Reply to: