Clevo 5600, ACPI/APM problems
Hi,
I've just bought a new machine, and installed Debian `Woody'
on it. It all works (after I tracked down the XFree 4.2.0
experimental release), except for power management.
The suspend button does nothing.
I can do
apm -s
to suspend the system, but nothing I can do wakes it up again.
I suspect that the CPU is running flat out all the time, because I'm
seeing only 60minutes of battery power.
The kernel logs say:
(1 If I disable ACPI in the kernel config)
Aug 14 17:38:54 numbat kernel: apm: BIOS version 1.2 Flags 0x03
(Driver version 1.16)
...
Aug 14 17:38:54 numbat kernel: ACPI: APM is already active, exiting
(2 If ACPI and APM are enabled)
Aug 14 07:48:31 numbat kernel: ACPI: have wakeup address 0xc0001000
Aug 14 07:48:31 numbat kernel: On node 0 totalpages: 130944
Aug 14 07:48:31 numbat kernel: zone(0): 4096 pages.
Aug 14 07:48:31 numbat kernel: zone(1): 126848 pages.
Aug 14 07:48:31 numbat kernel: zone(2): 0 pages.
Aug 14 07:48:31 numbat kernel: ACPI: RSDP (v000 PTLTD
) @ 0
x000f6390
Aug 14 07:48:31 numbat kernel: ACPI: RSDT (v001 PTLTD Sheeks
01540.00000) @ 0
x1fef6ba4
Aug 14 07:48:31 numbat kernel: ACPI: FADT (v001 Clevo 845MP
01540.00000) @ 0
x1fefaf2d
Aug 14 07:48:31 numbat kernel: ACPI: BOOT (v001 PTLTD $SBFTBL$
01540.00000) @ 0
x1fefafa1
Aug 14 07:48:31 numbat kernel: ACPI: MADT not present
Aug 14 07:48:31 numbat kernel: No local APIC present or hardware
disabled
Aug 14 07:48:31 numbat kernel: ACPI: Subsystem revision 20020725
Aug 14 07:48:31 numbat kernel: ACPI: Interpreter enabled
Aug 14 07:48:31 numbat kernel: ACPI: Using PIC for interrupt routing
Aug 14 07:48:31 numbat kernel: ACPI: System [ACPI] (supports S0 S3 S4
S5)
Aug 14 07:48:31 numbat kernel: ACPI: PCI Root Bridge [PCI0] (00:00)
Aug 14 07:48:31 numbat kernel: PCI: Probing PCI hardware (bus 00)
Aug 14 07:48:31 numbat kernel: Unknown bridge resource 2: assuming
transparent
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0._PR
T]
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.AGP
B._PRT]
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Routing Table
[\_SB_.PCI0.PCI
B._PRT]
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Link [LNKA] (IRQs
*11)
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Link [LNKB] (IRQs
*11)
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Link [LNKC] (IRQs
*5)
Aug 14 07:48:31 numbat kernel: ACPI: PCI Interrupt Link [LNKD] (IRQs
*9)
Aug 14 07:48:31 numbat kernel: ACPI: Embedded Controller [EC] (gpe 28)
Aug 14 07:48:31 numbat kernel: usb.c: registered new driver usbfs
Aug 14 07:48:31 numbat kernel: usb.c: registered new driver hub
Aug 14 07:48:31 numbat kernel: PCI: Using ACPI for IRQ routing
'pci=noacpi'
Aug 14 07:48:31 numbat kernel: SBF: Simple Boot Flag extension found
and enabled.
Aug 14 07:48:31 numbat kernel: SBF: Setting boot flags 0x1
Aug 14 07:48:31 numbat kernel: apm: BIOS version 1.2 Flags 0x03
(Driver version 1.16)
Aug 14 07:48:31 numbat kernel: apm: overridden by ACPI.
Aug 14 07:48:31 numbat kernel: ACPI: AC Adapter [ADP0] (on-line)
Aug 14 07:48:31 numbat kernel: ACPI: Battery Slot [BAT0] (battery
present)
Aug 14 07:48:31 numbat kernel: ACPI: Battery Slot [BAT1] (battery
absent)
Aug 14 07:48:31 numbat kernel: ACPI: Power Button (CM) [PWRB]
Aug 14 07:48:31 numbat kernel: ACPI: Lid Switch [LID]
Aug 14 07:48:31 numbat kernel: ACPI: Sleep Button (CM) [SLPB]
Aug 14 07:48:31 numbat kernel: ACPI: Processor [CPU0] (supports C1 C2,
2 performance states, 8 throttling states)
Aug 14 07:48:31 numbat kernel: ACPI: Thermal Zone [THM0] (40 C)
Reply to: