[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#862510: ohci-pci: frame counter not updating



Package: src:linux
Version: 4.9.18-1
Severity: important

When connecting a device (mini-box 256x64 picoLCD, listed in the kernel log as
'ITUNER INC USB-LCD-256x64') to one of the USB2 ports on this machine, it'll
run fine for up to several hours, and then disconnect, leaving the following
in the kernel log:
ohci-pci 0000:00:12.0: frame counter not updating; disabled
ohci-pci 0000:00:12.0: HC died; cleaning up

Note that in the log below, it managed to run for slightly over 2 minutes after
system boot before dying.


Connecting the device to a USB3 port, causing it to use xhci_hcd, appears to
work reliably.

I've seen similar bug reports for this issue on Ubuntu (I'm running Debian
stretch here):
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1634737
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1635012

The above cases appear to have been resolved by https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=a8006bd915095c40098bfcb684cc2bdfb414dc0d
 - however, I've verified that the changes introduced by this patch are already
applied to linux-image-4.9.0-2-amd64 ver 4.9.18-1.

My previous installation on here was wheezy, using a backported kernel from jessie.
This USB2 issue did not appear while wheezy was running.



-- Package-specific info:
** Version:
Linux version 4.9.0-2-amd64 (debian-kernel@lists.debian.org) (gcc version 6.3.0 20170321 (Debian 6.3.0-11) ) #1 SMP Debian 4.9.18-1 (2017-03-30)

** Command line:
placeholder root=/dev/mapper/balrog-root--stretch ro net.ifnames=0 biosdevname=0 quiet

** Not tainted

** Kernel log:
[   46.674217] lan0: port 1(eth0.2) entered blocking state
[   46.674219] lan0: port 1(eth0.2) entered disabled state
[   46.674298] device eth0.2 entered promiscuous mode
[   46.680647] lan0: port 1(eth0.2) entered blocking state
[   46.680649] lan0: port 1(eth0.2) entered forwarding state
[   47.732359] NFSD: Using /var/lib/nfs/v4recovery as the NFSv4 state recovery directory
[   47.732367] NFSD: starting 90-second grace period (net ffffffff81cd3980)
[   48.110022] xen:xen_evtchn: Event-channel device installed
[   57.821269] lan0: port 2(vif1.0) entered blocking state
[   57.821271] lan0: port 2(vif1.0) entered disabled state
[   57.821379] device vif1.0 entered promiscuous mode
[   57.824143] IPv6: ADDRCONF(NETDEV_UP): vif1.0: link is not ready
[   57.937745] Bridge firewalling registered
[   59.756110] xen-blkback: backend/vbd/1/51713: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[   59.768037] xen-blkback: backend/vbd/1/51714: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[   59.777334] xen-blkback: backend/vbd/1/51729: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[   59.796475] xen-blkback: backend/vbd/1/51745: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[   59.809462] xen-blkback: backend/vbd/1/51761: using 1 queues, protocol 1 (x86_64-abi) persistent grants
[   59.836503] vif vif-1-0 vif1.0: Guest Rx ready
[   59.836580] IPv6: ADDRCONF(NETDEV_CHANGE): vif1.0: link becomes ready
[   59.836627] lan0: port 2(vif1.0) entered blocking state
[   59.836629] lan0: port 2(vif1.0) entered forwarding state
[   65.697886] device vif2.0 entered promiscuous mode
[   65.700755] IPv6: ADDRCONF(NETDEV_UP): vif2.0: link is not ready
[   67.374042] vif vif-2-0 vif2.0: Guest Rx ready
[   67.374116] IPv6: ADDRCONF(NETDEV_CHANGE): vif2.0: link becomes ready
[   67.374717] xen-blkback: backend/vbd/2/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[   68.871065] lan0: port 3(vif3.0) entered blocking state
[   68.871069] lan0: port 3(vif3.0) entered disabled state
[   68.871236] device vif3.0 entered promiscuous mode
[   68.875165] IPv6: ADDRCONF(NETDEV_UP): vif3.0: link is not ready
[   69.290501] xen-blkback: backend/vbd/3/51713: using 1 queues, protocol 1 (x86_64-abi) 
[   69.308346] xen-blkback: backend/vbd/3/51714: using 1 queues, protocol 1 (x86_64-abi) 
[   69.337093] vif vif-3-0 vif3.0: Guest Rx ready
[   69.337170] IPv6: ADDRCONF(NETDEV_CHANGE): vif3.0: link becomes ready
[   69.337225] lan0: port 3(vif3.0) entered blocking state
[   69.337226] lan0: port 3(vif3.0) entered forwarding state
[   72.396111] GuestNet: port 2(vif4.0) entered blocking state
[   72.396113] GuestNet: port 2(vif4.0) entered disabled state
[   72.396227] device vif4.0 entered promiscuous mode
[   72.399081] IPv6: ADDRCONF(NETDEV_UP): vif4.0: link is not ready
[   74.197440] xen-blkback: backend/vbd/4/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[   74.225330] vif vif-4-0 vif4.0: Guest Rx ready
[   74.225383] IPv6: ADDRCONF(NETDEV_CHANGE): vif4.0: link becomes ready
[   74.225430] GuestNet: port 2(vif4.0) entered blocking state
[   74.225432] GuestNet: port 2(vif4.0) entered forwarding state
[   76.183978] lan0: port 4(vif5.0) entered blocking state
[   76.183980] lan0: port 4(vif5.0) entered disabled state
[   76.184089] device vif5.0 entered promiscuous mode
[   76.186851] IPv6: ADDRCONF(NETDEV_UP): vif5.0: link is not ready
[   77.858265] xen-blkback: backend/vbd/5/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[   77.880994] xen-blkback: backend/vbd/5/51714: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[   77.914863] vif vif-5-0 vif5.0: Guest Rx ready
[   77.914935] IPv6: ADDRCONF(NETDEV_CHANGE): vif5.0: link becomes ready
[   77.914999] lan0: port 4(vif5.0) entered blocking state
[   77.915001] lan0: port 4(vif5.0) entered forwarding state
[  122.160025] ohci-pci 0000:00:12.0: frame counter not updating; disabled
[  122.160064] ohci-pci 0000:00:12.0: HC died; cleaning up
[  122.160151] usb 11-3: USB disconnect, device number 2
[  122.163302] usb 11-4: USB disconnect, device number 3
[  154.647920] lan0: port 5(vif6.0) entered blocking state
[  154.647922] lan0: port 5(vif6.0) entered disabled state
[  154.648010] device vif6.0 entered promiscuous mode
[  154.650934] IPv6: ADDRCONF(NETDEV_UP): vif6.0: link is not ready
[  156.287702] vif vif-6-0 vif6.0: Guest Rx ready
[  156.287769] IPv6: ADDRCONF(NETDEV_CHANGE): vif6.0: link becomes ready
[  156.287828] lan0: port 5(vif6.0) entered blocking state
[  156.287829] lan0: port 5(vif6.0) entered forwarding state
[  156.292096] xen-blkback: backend/vbd/6/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[  246.999319] device vif2.0 left promiscuous mode
[ 5262.955605] usb 10-2: new full-speed USB device number 2 using xhci_hcd
[ 5263.144855] usb 10-2: New USB device found, idVendor=04d8, idProduct=c002
[ 5263.144858] usb 10-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 5263.144860] usb 10-2: Product: USB-LCD-256x64
[ 5263.144861] usb 10-2: Manufacturer: ITUNER INC
[ 5263.144862] usb 10-2: SerialNumber: Ver.00.03
[ 5263.295744] input: ITUNER INC USB-LCD-256x64 as /devices/pci0000:00/0000:00:15.2/0000:03:00.0/usb10/10-2/10-2:1.0/0003:04D8:C002.0003/input/input17
[ 5263.295822] Registered IR keymap rc-rc6-mce
[ 5263.295892] input: ITUNER INC USB-LCD-256x64 as /devices/pci0000:00/0000:00:15.2/0000:03:00.0/usb10/10-2/10-2:1.0/0003:04D8:C002.0003/rc/rc0/input18
[ 5263.295928] rc rc0: ITUNER INC USB-LCD-256x64 as /devices/pci0000:00/0000:00:15.2/0000:03:00.0/usb10/10-2/10-2:1.0/0003:04D8:C002.0003/rc/rc0
[ 5263.296313] rc rc0: lirc_dev: driver ir-lirc-codec (PicoLCD (graphic)) registered at minor = 0
[ 5263.297259] Console: switching to mono frame buffer device 32x8
[ 5280.099829] Console: switching to colour VGA+ 80x25
[ 5727.382715] device vif8.0 entered promiscuous mode
[ 5727.385595] IPv6: ADDRCONF(NETDEV_UP): vif8.0: link is not ready
[ 5728.957119] xen-blkback: backend/vbd/8/51713: using 2 queues, protocol 1 (x86_64-abi) persistent grants
[ 5728.993444] vif vif-8-0 vif8.0: Guest Rx ready
[ 5728.993511] IPv6: ADDRCONF(NETDEV_CHANGE): vif8.0: link becomes ready
[ 5838.321825] audit: type=1305 audit(1494695633.399:2): audit_pid=6641 old=0 auid=4294967295 ses=4294967295 res=1

** Model information
sys_vendor: To Be Filled By O.E.M.
product_name: To Be Filled By O.E.M.
product_version: To Be Filled By O.E.M.
chassis_vendor: To Be Filled By O.E.M.
chassis_version: To Be Filled By O.E.M.
bios_vendor: American Megatrends Inc.
bios_version: P3.30
board_vendor: ASRock
board_name: FM2A88X Extreme4+
board_version:         

** Loaded modules:
xt_physdev
br_netfilter
iptable_filter
xen_netback
xen_blkback
xen_gntdev
xen_evtchn
xenfs
xen_privcmd
8021q
garp
mrp
bridge
stp
llc
edac_mce_amd
edac_core
crct10dif_pclmul
crc32_pclmul
ghash_clmulni_intel
snd_hda_codec_realtek
ir_lirc_codec
snd_hda_codec_generic
lirc_dev
snd_hda_codec_hdmi
ir_rc6_decoder
snd_hda_intel
rc_rc6_mce
amdkfd
evdev
pcspkr
snd_hda_codec
radeon
serio_raw
snd_hda_core
ttm
shpchp
snd_hwdep
snd_pcm
drm_kms_helper
snd_timer
snd
soundcore
sg
hid_picolcd
rc_core
fam15h_power
k10temp
drm
sp5100_tco
i2c_algo_bit
video
button
tpm_tis
tpm_tis_core
tpm
nfsd
aoe
ip_tables
x_tables
autofs4
xfs
raid10
raid0
multipath
linear
rpcsec_gss_krb5
auth_rpcgss
nfsv4
dns_resolver
nfsv3
nfs_acl
nfs
lockd
grace
sunrpc
fscache
dm_snapshot
dm_bufio
dm_mod
raid456
async_raid6_recov
async_memcpy
async_pq
async_xor
async_tx
xor
raid6_pq
libcrc32c
crc32c_generic
raid1
md_mod
hid_generic
usbhid
hid
sr_mod
cdrom
sd_mod
ata_generic
ohci_pci
crc32c_intel
aesni_intel
aes_x86_64
glue_helper
lrw
alx
gf128mul
ablk_helper
mdio
cryptd
ahci
libahci
xhci_pci
pata_atiixp
uhci_hcd
xhci_hcd
ohci_hcd
ehci_pci
libata
ehci_hcd
i2c_piix4
usbcore
scsi_mod
usb_common

** PCI devices:
00:00.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Root Complex [1022:1422]
	Subsystem: ASRock Incorporation Family 15h (Models 30h-3fh) Processor Root Complex [1849:1422]
	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:00.2 IOMMU [0806]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) I/O Memory Management Unit [1022:1423]
	Subsystem: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) I/O Memory Management Unit [1022:1423]
	Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0
	Interrupt: pin A routed to IRQ 255
	Capabilities: <access denied>

00:01.0 VGA compatible controller [0300]: Advanced Micro Devices, Inc. [AMD/ATI] Kaveri [Radeon R7 Graphics] [1002:1313] (prog-if 00 [VGA controller])
	Subsystem: ASRock Incorporation Kaveri [Radeon R7 Graphics] [1849:1313]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at c0000000 (64-bit, prefetchable) [size=256M]
	Region 2: Memory at d0000000 (64-bit, prefetchable) [size=8M]
	Region 4: I/O ports at f000 [size=256]
	Region 5: Memory at feb00000 (32-bit, non-prefetchable) [size=256K]
	Expansion ROM at 000c0000 [disabled] [size=128K]
	Capabilities: <access denied>
	Kernel modules: radeon

00:01.1 Audio device [0403]: Advanced Micro Devices, Inc. [AMD/ATI] Kaveri HDMI/DP Audio Controller [1002:1308]
	Subsystem: ASRock Incorporation Kaveri HDMI/DP Audio Controller [1849:1308]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 107
	Region 0: Memory at feb64000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:02.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device [1022:1424]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:03.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device [1022:1424]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:04.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Device [1022:1424]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:10.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller [1022:7814] (rev 09) (prog-if 30 [XHCI])
	Subsystem: ASRock Incorporation FCH USB XHCI Controller [1849:7814]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at feb6a000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

00:10.1 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB XHCI Controller [1022:7814] (rev 09) (prog-if 30 [XHCI])
	Subsystem: ASRock Incorporation FCH USB XHCI Controller [1849:7814]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at feb68000 (64-bit, non-prefetchable) [size=8K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

00:11.0 SATA controller [0106]: Advanced Micro Devices, Inc. [AMD] FCH SATA Controller [AHCI mode] [1022:7801] (rev 40) (prog-if 01 [AHCI 1.0])
	Subsystem: ASRock Incorporation FCH SATA Controller [AHCI mode] [1849:7801]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx+
	Latency: 32
	Interrupt: pin A routed to IRQ 91
	Region 0: I/O ports at f190 [size=8]
	Region 1: I/O ports at f180 [size=4]
	Region 2: I/O ports at f170 [size=8]
	Region 3: I/O ports at f160 [size=4]
	Region 4: I/O ports at f150 [size=16]
	Region 5: Memory at feb71000 (32-bit, non-prefetchable) [size=2K]
	Capabilities: <access denied>
	Kernel driver in use: ahci
	Kernel modules: ahci

00:12.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller [1022:7807] (rev 11) (prog-if 10 [OHCI])
	Subsystem: ASRock Incorporation FCH USB OHCI Controller [1849:7807]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at feb70000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci
	Kernel modules: ohci_pci

00:12.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller [1022:7808] (rev 11) (prog-if 20 [EHCI])
	Subsystem: ASRock Incorporation FCH USB EHCI Controller [1849:7808]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at feb6f000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:13.0 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller [1022:7807] (rev 11) (prog-if 10 [OHCI])
	Subsystem: ASRock Incorporation FCH USB OHCI Controller [1849:7807]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at feb6e000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci
	Kernel modules: ohci_pci

00:13.2 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB EHCI Controller [1022:7808] (rev 11) (prog-if 20 [EHCI])
	Subsystem: ASRock Incorporation FCH USB EHCI Controller [1849:7808]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 17
	Region 0: Memory at feb6d000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

00:14.0 SMBus [0c05]: Advanced Micro Devices, Inc. [AMD] FCH SMBus Controller [1022:780b] (rev 16)
	Subsystem: ASRock Incorporation FCH SMBus Controller [1849:780b]
	Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel driver in use: piix4_smbus
	Kernel modules: i2c_piix4, sp5100_tco

00:14.1 IDE interface [0101]: Advanced Micro Devices, Inc. [AMD] FCH IDE Controller [1022:780c] (prog-if 8a [Master SecP PriP])
	Subsystem: ASRock Incorporation FCH IDE Controller [1849:780c]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Interrupt: pin B routed to IRQ 17
	Region 0: I/O ports at 01f0 [size=8]
	Region 1: I/O ports at 03f4
	Region 2: I/O ports at 0170 [size=8]
	Region 3: I/O ports at 0374
	Region 4: I/O ports at f100 [size=16]
	Kernel driver in use: pata_atiixp
	Kernel modules: pata_atiixp, ata_generic

00:14.2 Audio device [0403]: Advanced Micro Devices, Inc. [AMD] FCH Azalia Controller [1022:780d] (rev 01)
	Subsystem: ASRock Incorporation FCH Azalia Controller [1849:c892]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=slow >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 16
	Region 0: Memory at feb60000 (64-bit, non-prefetchable) [size=16K]
	Capabilities: <access denied>
	Kernel driver in use: snd_hda_intel
	Kernel modules: snd_hda_intel

00:14.3 ISA bridge [0601]: Advanced Micro Devices, Inc. [AMD] FCH LPC Bridge [1022:780e] (rev 11)
	Subsystem: ASRock Incorporation FCH LPC Bridge [1849:780e]
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0

00:14.4 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] FCH PCI Bridge [1022:780f] (rev 40) (prog-if 01 [Subtractive decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: fea00000-feafffff
	Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-

00:14.5 USB controller [0c03]: Advanced Micro Devices, Inc. [AMD] FCH USB OHCI Controller [1022:7809] (rev 11) (prog-if 10 [OHCI])
	Subsystem: ASRock Incorporation FCH USB OHCI Controller [1849:7809]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 18
	Region 0: Memory at feb6c000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci-pci
	Kernel modules: ohci_pci

00:15.0 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 0) [1022:43a0] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 86
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:15.2 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 2) [1022:43a2] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 87
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	Memory behind bridge: fe900000-fe9fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:15.3 PCI bridge [0604]: Advanced Micro Devices, Inc. [AMD] Hudson PCI to PCI bridge (PCIE port 3) [1022:43a3] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 88
	Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: fe800000-fe8fffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: <access denied>
	Kernel driver in use: pcieport
	Kernel modules: shpchp

00:18.0 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 0 [1022:141a]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.1 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 1 [1022:141b]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.2 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 2 [1022:141c]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:18.3 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 3 [1022:141d]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Capabilities: <access denied>
	Kernel driver in use: k10temp
	Kernel modules: k10temp

00:18.4 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 4 [1022:141e]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Kernel driver in use: fam15h_power
	Kernel modules: fam15h_power

00:18.5 Host bridge [0600]: Advanced Micro Devices, Inc. [AMD] Family 15h (Models 30h-3fh) Processor Function 5 [1022:141f]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

01:05.0 USB controller [0c03]: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
	Subsystem: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 20
	Region 4: I/O ports at e020 [size=32]
	Capabilities: <access denied>
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

01:05.1 USB controller [0c03]: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038] (rev 62) (prog-if 00 [UHCI])
	Subsystem: VIA Technologies, Inc. VT82xx/62xx UHCI USB 1.1 Controller [1106:3038]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 21
	Region 4: I/O ports at e000 [size=32]
	Capabilities: <access denied>
	Kernel driver in use: uhci_hcd
	Kernel modules: uhci_hcd

01:05.2 USB controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 65) (prog-if 20 [EHCI])
	Subsystem: VIA Technologies, Inc. USB 2.0 Controller [1106:3104]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32, Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 22
	Region 0: Memory at fea00000 (32-bit, non-prefetchable) [size=256]
	Capabilities: <access denied>
	Kernel driver in use: ehci-pci
	Kernel modules: ehci_pci

03:00.0 USB controller [0c03]: Etron Technology, Inc. EJ188/EJ198 USB 3.0 Host Controller [1b6f:7052] (prog-if 30 [XHCI])
	Subsystem: ASRock Incorporation EJ188/EJ198 USB 3.0 Host Controller [1849:7052]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 105
	Region 0: Memory at fe900000 (64-bit, non-prefetchable) [size=32K]
	Capabilities: <access denied>
	Kernel driver in use: xhci_hcd
	Kernel modules: xhci_pci

04:00.0 Ethernet controller [0200]: Qualcomm Atheros QCA8171 Gigabit Ethernet [1969:10a1] (rev 10)
	Subsystem: ASRock Incorporation QCA8171 Gigabit Ethernet [1849:10a1]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 106
	Region 0: Memory at fe800000 (64-bit, non-prefetchable) [size=256K]
	Region 2: I/O ports at d000 [size=128]
	Capabilities: <access denied>
	Kernel driver in use: alx
	Kernel modules: alx


** USB devices:
Bus 012 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 010 Device 002: ID 04d8:c002 Microchip Technology, Inc. 
Bus 010 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 014 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 013 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 011 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 009 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 008 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 007 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 006 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub


-- System Information:
Debian Release: 9.0
  APT prefers testing
  APT policy: (500, 'testing')
Architecture: amd64
 (x86_64)

Kernel: Linux 4.9.0-2-amd64 (SMP w/4 CPU cores)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)

Versions of packages linux-image-4.9.0-2-amd64 depends on:
ii  initramfs-tools [linux-initramfs-tool]  0.130
ii  kmod                                    23-2
ii  linux-base                              4.5

Versions of packages linux-image-4.9.0-2-amd64 recommends:
pn  firmware-linux-free  <none>
pn  irqbalance           <none>

Versions of packages linux-image-4.9.0-2-amd64 suggests:
pn  debian-kernel-handbook  <none>
ii  grub-pc                 2.02~beta3-5
pn  linux-doc-4.9           <none>

Versions of packages linux-image-4.9.0-2-amd64 is related to:
pn  firmware-amd-graphics                      <none>
pn  firmware-atheros                           <none>
pn  firmware-bnx2                              <none>
pn  firmware-bnx2x                             <none>
pn  firmware-brcm80211                         <none>
pn  firmware-cavium                            <none>
pn  firmware-intel-sound                       <none>
pn  firmware-intelwimax                        <none>
pn  firmware-ipw2x00                           <none>
pn  firmware-ivtv                              <none>
pn  firmware-iwlwifi                           <none>
pn  firmware-libertas                          <none>
pn  firmware-linux-nonfree                     <none>
pn  firmware-misc-nonfree                      <none>
pn  firmware-myricom                           <none>
pn  firmware-netxen                            <none>
pn  firmware-qlogic                            <none>
pn  firmware-realtek                           <none>
pn  firmware-samsung                           <none>
pn  firmware-siano                             <none>
pn  firmware-ti-connectivity                   <none>
ii  xen-hypervisor-4.8-amd64 [xen-hypervisor]  4.8.1-1+deb9u1

-- no debconf information


Reply to: