Package: src:linux
Version: 4.0.8-1
Severity: important
Dear Maintainer,
after update of the kernel (3.16 > 4.0.0) the system hangs at boot. I found out,
that the kernel does not bind the ethernet interface correctly to the module.
The ethernet device is a Atheros AR8132 and the kernel module for it is atl1c.
Due to this behaviour, boot hangs with the message:
[***] An LSB job is running: Raise network interfaces
This problem appears from time to time in the forums, for example here:
http://forums.debian.net/viewtopic.php?f=5&t=119326
I tried to manually unload and load the kernel module, with no success.
Also I tried several boots, and it showed, that the device sometimes is bound, and sometimes
not. But there is always the very long delay at boot (about 70 - 90 seconds).
For testing purposes I reverted back to kernel-3.16, and everything went back to normal (the delay then is 1 - 2 seconds).
When the device is not bound correctly with kernel 4.0, then "eth0" is not existent.
Please note, that I am using hard IP, so there is never a delay for dhcp requests.
And as I said, with kernel-3.16 everything is working fine, with kernel 4.0 I get the problem.
Please note also: When I made the update, the only thing I updated was the kernel, so other packages are not involved. And I can surely reproduce the bug.
It would be nice, if you could take a look at the involved kernel modules or kernel itself.
Thank you very much for reading this.
Best regards
Hans-J. Ullrich
-- Package-specific info:
** Version:
Linux version 4.0.0-2-686-pae (debian-kernel@lists.debian.org) (gcc version 4.9.3 (Debian 4.9.3-1) ) #1 SMP Debian 4.0.8-1 (2015-07-11)
** Command line:
BOOT_IMAGE=/vmlinuz-4.0.0-2-686-pae root=UUID=da2bbacb-1b05-461e-8b72-9eef666b9bf6 ro quiet
** Not tainted
** Kernel log:
[ 14.944422] Bluetooth: Core ver 2.20
[ 14.944484] NET: Registered protocol family 31
[ 14.944487] Bluetooth: HCI device and connection manager initialized
[ 14.944500] Bluetooth: HCI socket layer initialized
[ 14.944509] Bluetooth: L2CAP socket layer initialized
[ 14.944548] Bluetooth: SCO socket layer initialized
[ 14.974393] ath: phy0: ASPM enabled: 0x42
[ 14.974400] ath: EEPROM regdomain: 0x60
[ 14.974402] ath: EEPROM indicates we should expect a direct regpair map
[ 14.974407] ath: Country alpha2 being used: 00
[ 14.974409] ath: Regpair used: 0x60
[ 15.001042] usbcore: registered new interface driver btusb
[ 15.064594] Console: switching to colour frame buffer device 128x37
[ 15.076291] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 15.076299] i915 0000:00:02.0: registered panic notifier
[ 15.135695] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
[ 15.136946] ieee80211 phy0: Atheros AR9285 Rev:2 mem=0xf8280000, irq=17
[ 15.280349] uvcvideo: Found UVC 1.00 device USB2.0 UVC 1.3M WebCam (13d3:5095)
[ 15.303352] input: USB2.0 UVC 1.3M WebCam as /devices/pci0000:00/0000:00:1d.7/usb1/1-2/1-2:1.0/input/input10
[ 15.308513] usbcore: registered new interface driver uvcvideo
[ 15.308524] USB Video Class driver (1.1.1)
[ 15.461206] usbcore: registered new interface driver usbserial
[ 15.461278] usbcore: registered new interface driver usbserial_generic
[ 15.461342] usbserial: USB Serial support registered for generic
[ 15.522647] usbcore: registered new interface driver option
[ 15.522731] usbserial: USB Serial support registered for GSM modem (1-port)
[ 15.523246] option 5-2:1.0: GSM modem (1-port) converter detected
[ 15.544989] usb 5-2: GSM modem (1-port) converter now attached to ttyUSB0
[ 15.545097] option 5-2:1.1: GSM modem (1-port) converter detected
[ 15.552517] usb 5-2: GSM modem (1-port) converter now attached to ttyUSB1
[ 15.552604] option 5-2:1.2: GSM modem (1-port) converter detected
[ 15.564132] usb 5-2: GSM modem (1-port) converter now attached to ttyUSB2
[ 15.701167] Adding 6143996k swap on /dev/sda6. Priority:-1 extents:1 across:6143996k SSFS
[ 15.859540] psmouse serio1: synaptics: queried max coordinates: x [..5808], y [..4842]
[ 15.907562] asus_wmi: ASUS WMI generic driver loaded
[ 15.933874] asus_wmi: Initialization: 0x0
[ 15.933998] asus_wmi: BIOS WMI version: 0.5
[ 15.934223] asus_wmi: SFUN value: 0x0
[ 15.959810] input: Eee PC WMI hotkeys as /devices/platform/eeepc-wmi/input/input11
[ 15.988713] iTCO_vendor_support: vendor-support=0
[ 15.990726] iTCO_wdt: Intel TCO WatchDog Timer Driver v1.11
[ 15.990829] iTCO_wdt: unable to reset NO_REBOOT flag, device disabled by hardware/BIOS
[ 16.015803] psmouse serio1: synaptics: Touchpad model: 1, fw: 7.2, id: 0x1a0b1, caps: 0xd04733/0xa40000/0xa0000, board id: 0, fw id: 570166
[ 16.155976] input: SynPS/2 Synaptics TouchPad as /devices/platform/i8042/serio1/input/input9
[ 16.272184] EXT4-fs (sda5): mounting ext2 file system using the ext4 subsystem
[ 16.289618] EXT4-fs (sda5): mounted filesystem without journal. Opts: (null)
[ 16.514652] cfg80211: World regulatory domain updated:
[ 16.514664] cfg80211: DFS Master region: unset
[ 16.514670] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 16.514679] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.514687] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.514694] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.514702] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[ 16.514710] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[ 16.514718] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[ 16.514724] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 16.514731] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 18.024638] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 18.024664] lpc_ich 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
[ 18.024681] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 18.134472] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 18.134506] lpc_ich 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
[ 18.134529] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 18.135062] asus_wmi: Backlight controlled by ACPI video driver
[ 18.135399] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 18.135427] lpc_ich 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
[ 18.135447] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 24.535150] EXT4-fs (dm-1): mounted filesystem with ordered data mode. Opts: discard,errors=remount-ro
[ 24.668343] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 24.668366] lpc_ich 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
[ 24.668380] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 24.740353] systemd-journald[281]: Received request to flush runtime journal from PID 1
[ 25.672686] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 25.672712] lpc_ich 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
[ 25.672728] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 25.777231] i915 0000:00:02.0: BAR 6: [??? 0x00000000 flags 0x2] has bogus alignment
[ 25.777258] lpc_ich 0000:00:1f.0: BAR 13: [io 0x0800-0x087f] has bogus alignment
[ 25.777275] pci 0000:00:1e.0: PCI bridge to [bus 05]
[ 32.237369] EXT4-fs (dm-2): mounted filesystem with ordered data mode. Opts: discard,errors=remount-ro
[ 33.822878] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 34.901913] wlan0: authenticate with 00:1a:4f:21:8e:32
[ 34.920361] wlan0: send auth to 00:1a:4f:21:8e:32 (try 1/3)
[ 34.922157] wlan0: authenticated
[ 34.924118] wlan0: associate with 00:1a:4f:21:8e:32 (try 1/3)
[ 34.928631] wlan0: RX AssocResp from 00:1a:4f:21:8e:32 (capab=0x411 status=0 aid=2)
[ 34.928858] wlan0: associated
[ 34.928897] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 125.974223] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 126.406009] NET4: DECnet for Linux: V.2.5.68s (C) 1995-2003 Linux DECnet Project Team
[ 126.406334] DECnet: Routing cache hash table of 1024 buckets, 8Kbytes
[ 126.406355] NET: Registered protocol family 12
[ 127.320521] apm: BIOS not found.
[ 127.558538] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 127.558540] Bluetooth: BNEP filters: protocol multicast
[ 127.558556] Bluetooth: BNEP socket layer initialized
[ 127.956238] NET: Registered protocol family 23
[ 144.777897] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 170.709361] perf interrupt took too long (2526 > 2500), lowering kernel.perf_event_max_sample_rate to 50000
[ 260.791546] perf interrupt took too long (5010 > 5000), lowering kernel.perf_event_max_sample_rate to 25000
[ 473.181298] fuse init (API version 7.23)
** Model information
not available
** Loaded modules:
fuse
xt_multiport
iptable_filter
ip_tables
x_tables
snd_hrtimer
snd_seq_midi
snd_seq_midi_event
snd_rawmidi
snd_seq
snd_seq_device
binfmt_misc
cpufreq_conservative
cpufreq_userspace
cpufreq_powersave
cpufreq_stats
irda
crc_ccitt
bnep
decnet
ctr
ccm
joydev
iTCO_wdt
iTCO_vendor_support
eeepc_wmi
asus_wmi
option
usb_wwan
usbserial
uvcvideo
videobuf2_vmalloc
videobuf2_memops
videobuf2_core
v4l2_common
arc4
btusb
bluetooth
ath9k
ath9k_common
evdev
psmouse
serio_raw
ath9k_hw
snd_hda_codec_realtek
ath
snd_hda_codec_generic
i915
snd_hda_intel
snd_hda_controller
sg
mac80211
lpc_ich
mfd_core
snd_hda_codec
drm_kms_helper
snd_hwdep
rng_core
snd_pcm_oss
cfg80211
snd_mixer_oss
drm
snd_pcm
i2c_algo_bit
snd_timer
snd
shpchp
soundcore
wmi
battery
ac
video
sparse_keymap
acpi_cpufreq
rfkill
button
processor
sbs
sbshc
max6650
coretemp
gspca_sn9c20x
gspca_main
videodev
media
loop
atl1
mii
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
algif_skcipher
af_alg
usb_storage
sha256_generic
dm_crypt
dm_mod
aes_i586
xts
lrw
gf128mul
ablk_helper
cryptd
sd_mod
ahci
libahci
libata
scsi_mod
uhci_hcd
ehci_pci
ehci_hcd
usbcore
atl1c
usb_common
thermal
thermal_sys
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 945GSE Express Memory Controller Hub [8086:27ac] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:8340]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 945GSE Express Integrated Graphics Controller [8086:27ae] (rev 03) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:8340]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7e00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at dc00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f7dc0000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:02.1 Display controller [0380]: Intel Corporation Mobile 945GM/GMS/GME, 943/940GML Express Integrated Graphics Controller [8086:27a6] (rev 03)
Subsystem: ASUSTeK Computer Inc. Device [1043:8340]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f7e80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation NM10/ICH7 Family High Definition Audio Controller [8086:27d8] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:8398]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 28
Region 0: Memory at f7db8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 1 [8086:27d0] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: 80000000-801fffff
Prefetchable memory behind bridge: 0000000080200000-00000000803fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 2 [8086:27d2] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=02, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: f8000000-fbffffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation NM10/ICH7 Family PCI Express Port 4 [8086:27d6] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f7f00000-f7ffffff
Prefetchable memory behind bridge: 0000000080400000-00000000805fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #1 [8086:27c8] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at d400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #2 [8086:27c9] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at d480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #3 [8086:27ca] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at d800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB UHCI Controller #4 [8086:27cb] (rev 02) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at d880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation NM10/ICH7 Family USB2 EHCI Controller [8086:27cc] (rev 02) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7db7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev e2) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801GBM (ICH7-M) LPC Interface Bridge [8086:27b9] (rev 02)
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 82801GBM/GHM (ICH7-M Family) SATA Controller [AHCI mode] [8086:27c5] (rev 02) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:830f]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 27
Region 0: I/O ports at d080 [size=8]
Region 1: I/O ports at d000 [size=4]
Region 2: I/O ports at cc00 [size=8]
Region 3: I/O ports at c880 [size=4]
Region 4: I/O ports at c800 [size=16]
Region 5: Memory at f7db7800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ahci
01:00.0 Ethernet controller [0200]: Qualcomm Atheros AR8132 Fast Ethernet [1969:1062] (rev c0)
Subsystem: ASUSTeK Computer Inc. Device [1043:838a]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 29
Region 0: Memory at f7fc0000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at ec00 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
02:00.0 Network controller [0280]: Qualcomm Atheros AR9285 Wireless Network Adapter (PCI-Express) [168c:002b] (rev 01)
Subsystem: AzureWave AW-NE785 / AW-NE785H 802.11bgn Wireless Full or Half-size Mini PCIe Card [1a3b:1089]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbff0000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath9k
** USB devices:
Bus 001 Device 002: ID 13d3:5095 IMC Networks
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 005 Device 003: ID 12d1:1001 Huawei Technologies Co., Ltd. E169/E620/E800 HSDPA Modem
Bus 005 Device 002: ID 0b05:b700 ASUSTek Computer, Inc. Broadcom Bluetooth 2.1
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
-- System Information:
Debian Release: stretch/sid
APT prefers testing
APT policy: (500, 'testing'), (500, 'stable')
Architecture: i386 (i686)
Kernel: Linux 4.0.0-2-686-pae (SMP w/2 CPU cores)
Locale: LANG=de_DE@euro, LC_CTYPE=de_DE@euro (charmap=UTF-8) (ignored: LC_ALL set to de_DE.UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-4.0.0-2-686-pae depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.120
ii kmod 20-1
ii linux-base 3.5
Versions of packages linux-image-4.0.0-2-686-pae recommends:
ii firmware-linux-free 3.3
ii irqbalance 1.0.6-3
ii libc6-i686 2.19-18
Versions of packages linux-image-4.0.0-2-686-pae suggests:
pn debian-kernel-handbook <none>
ii extlinux 3:6.03+dfsg-7
ii grub-pc 2.02~beta2-26
pn linux-doc-4.0 <none>
Versions of packages linux-image-4.0.0-2-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
ii firmware-linux 0.44
ii firmware-linux-nonfree 0.44
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-4.0.0-2-686-pae/postinst/mips-initrd-4.0.0-2-686-pae:
linux-image-4.0.0-2-686-pae/postinst/depmod-error-initrd-4.0.0-2-686-pae: false
* linux-image-4.0.0-2-686-pae/prerm/removing-running-kernel-4.0.0-2-686-pae: false
|