Bug#782442: linux-image-3.16.0-4-amd64: USB3 regression: External hard disk does not work anymore
Package: src:linux
Version: 3.16.7-ckt9-1
Severity: normal
Dear Maintainer,
one of my external hard disks does not work anymore with current kernels,
when I plug it into my USB3 port.
Steps to reproduce:
* Boot the system without the disk being connected
* Plug the disk into my Laptop's USB3 port
* Watch dmesg and my DE's removable media notification
Behaviour with kernels 3.16.7-ckt9-1 and 3.14.15-2:
As you can see in the kernel log below, I get lots of error junk in
dmesg. The disk is not recognized. The disk spins up though, so
it seems to notice that there is "something" at the other end
of the cable.
I unplugged the disk before doing this report, so it can't show up in
the USB device listing below. However, when I call "lsusb" with the
disk connected (while the kernel prints all these errors), no additional
device shows up.
Behaviour with 3.13.10-1 and older kernels:
The disk is recognized correctly, and I can access my data at USB3 speed.
Here's the dmesg that is printed in that case:
>>>>> successfull (old kernel) dmesg start <<<<<<
[ 37.930632] usb usb1: root hub lost power or was reset
[ 37.930641] usb usb3: root hub lost power or was reset
[ 37.935270] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 37.935290] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 37.935308] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 37.935324] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 37.935338] xhci_hcd 0000:04:00.0: irq 47 for MSI/MSI-X
[ 38.258763] usb 3-1: new SuperSpeed USB device number 2 using xhci_hcd
[ 38.275187] usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 38.276132] usb 3-1: New USB device found, idVendor=0bc2, idProduct=3312
[ 38.276140] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 38.276144] usb 3-1: Product: Expansion Desk
[ 38.276148] usb 3-1: Manufacturer: Seagate
[ 38.276152] usb 3-1: SerialNumber: NA4NANTR
[ 38.301581] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 38.301753] scsi7 : usb-storage 3-1:1.0
[ 38.301905] usbcore: registered new interface driver usb-storage
[ 39.300862] scsi 7:0:0:0: Direct-Access Seagate Expansion Desk 0739 PQ: 0 ANSI: 6
[ 39.301577] sd 7:0:0:0: Attached scsi generic sg3 type 0
[ 39.303473] sd 7:0:0:0: [sdd] Spinning up disk...
[ 44.758288] .........ready
[ 52.799760] sd 7:0:0:0: [sdd] 1220942645 4096-byte logical blocks: (5.00 TB/4.54 TiB)
[ 52.800311] sd 7:0:0:0: [sdd] Write Protect is off
[ 52.800314] sd 7:0:0:0: [sdd] Mode Sense: 2b 00 10 08
[ 52.800857] sd 7:0:0:0: [sdd] Write cache: enabled, read cache: enabled, supports DPO and FUA
[ 52.801638] sd 7:0:0:0: [sdd] 1220942645 4096-byte logical blocks: (5.00 TB/4.54 TiB)
[ 53.080785] sdd: sdd1
[ 53.081595] sd 7:0:0:0: [sdd] 1220942645 4096-byte logical blocks: (5.00 TB/4.54 TiB)
[ 53.082717] sd 7:0:0:0: [sdd] Attached SCSI disk
>>>>> successfull (old kernel) dmesg end <<<<<<
I will try to reproduce this with upstream kernels, and if I can, report the
problem upstream.
With all kernels I tried, if I connect the same disk to a USB2 port, it works
all right. But of course, disk access is much slower then.
The USB3 port also sometimes makes problems with other devices, but that's way less
reproducible - hence I am concentrating on this particular disk. In particular,
after unsuccessfully connecting the disk to the USB3 port, with high likelyhood,
no USB device whatsoever will work on that port until a reboot.
Sorry for reporting this so short before the Jessie release - I noticed the problem
a while ago already, but did not have the time to figure out the details.
Kind regards,
Ralf
-- Package-specific info:
** Version:
Linux version 3.16.0-4-amd64 (debian-kernel@lists.debian.org) (gcc version 4.8.4 (Debian 4.8.4-1) ) #1 SMP Debian 3.16.7-ckt9-1 (2015-04-08)
** Command line:
BOOT_IMAGE=/vmlinuz-3.16.0-4-amd64 root=/dev/mapper/cryptvg-rootlv ro quiet splash
** Tainted: WO (4608)
* Taint on warning.
* Out-of-tree module has been loaded.
** Kernel log:
[ 57.085970] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 57.085983] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 58.071879] usb usb2: root hub lost power or was reset
[ 58.071888] usb usb3: root hub lost power or was reset
[ 58.076523] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 58.076543] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 58.076558] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 58.076575] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 58.076590] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 59.068886] usb usb2: root hub lost power or was reset
[ 59.068896] usb usb3: root hub lost power or was reset
[ 59.078780] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 59.078799] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 59.078815] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 59.078829] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 59.078844] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 60.062988] usb usb2: root hub lost power or was reset
[ 60.062996] usb usb3: root hub lost power or was reset
[ 60.067631] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 60.067650] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 60.067666] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 60.067682] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 60.067699] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 61.061944] usb usb2: root hub lost power or was reset
[ 61.061953] usb usb3: root hub lost power or was reset
[ 61.071856] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 61.071872] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 61.071885] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 61.071898] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 61.071911] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 62.057690] usb usb2: root hub lost power or was reset
[ 62.057699] usb usb3: root hub lost power or was reset
[ 62.062338] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 62.062357] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 62.062373] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 62.062390] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 62.062405] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 63.058090] usb usb2: root hub lost power or was reset
[ 63.058099] usb usb3: root hub lost power or was reset
[ 63.067987] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 63.068004] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 63.068019] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 63.068034] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 63.068048] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 64.055084] usb usb2: root hub lost power or was reset
[ 64.055093] usb usb3: root hub lost power or was reset
[ 64.059729] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 64.059749] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 64.059765] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 64.059781] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 64.059797] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 65.056580] usb usb2: root hub lost power or was reset
[ 65.056589] usb usb3: root hub lost power or was reset
[ 65.066478] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 65.066497] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 65.066514] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 65.066530] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 65.066547] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 66.054544] usb usb2: root hub lost power or was reset
[ 66.054553] usb usb3: root hub lost power or was reset
[ 66.059193] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 66.059212] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 66.059229] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 66.059245] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 66.059261] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 67.052906] usb usb2: root hub lost power or was reset
[ 67.052915] usb usb3: root hub lost power or was reset
[ 67.062805] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 67.062825] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 67.062842] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 67.062860] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 67.062875] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 68.051609] usb usb2: root hub lost power or was reset
[ 68.051618] usb usb3: root hub lost power or was reset
[ 68.056253] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 68.056272] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 68.056288] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 68.056305] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 68.056320] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 69.050621] usb usb2: root hub lost power or was reset
[ 69.050630] usb usb3: root hub lost power or was reset
[ 69.060521] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 69.060539] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 69.060555] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 69.060569] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 69.060583] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 70.049888] usb usb2: root hub lost power or was reset
[ 70.049897] usb usb3: root hub lost power or was reset
[ 70.054532] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 70.054551] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 70.054567] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 70.054583] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 70.054599] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
[ 71.049411] usb usb2: root hub lost power or was reset
[ 71.049420] usb usb3: root hub lost power or was reset
[ 71.059306] xhci_hcd 0000:04:00.0: irq 42 for MSI/MSI-X
[ 71.059323] xhci_hcd 0000:04:00.0: irq 43 for MSI/MSI-X
[ 71.059338] xhci_hcd 0000:04:00.0: irq 44 for MSI/MSI-X
[ 71.059353] xhci_hcd 0000:04:00.0: irq 45 for MSI/MSI-X
[ 71.059368] xhci_hcd 0000:04:00.0: irq 46 for MSI/MSI-X
** Model information
sys_vendor: ASUSTeK Computer Inc.
product_name: K53SM
product_version: 1.0
chassis_vendor: ASUSTeK Computer Inc.
chassis_version: 1.0
bios_vendor: American Megatrends Inc.
bios_version: K53SM.214
board_vendor: ASUSTeK Computer Inc.
board_name: K53SM
board_version: 1.0
** Loaded modules:
rfcomm
xt_tcpudp
ip6t_rpfilter
ip6t_REJECT
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
ipt_REJECT
xt_conntrack
ebtable_nat
ebtable_broute
bridge
stp
llc
ebtable_filter
ebtables
ip6table_nat
nf_conntrack_ipv6
nf_defrag_ipv6
nf_nat_ipv6
ip6table_mangle
ip6table_security
ip6table_raw
ip6table_filter
ip6_tables
iptable_nat
nf_conntrack_ipv4
nf_defrag_ipv4
nf_nat_ipv4
nf_nat
nf_conntrack
iptable_mangle
iptable_security
iptable_raw
iptable_filter
ip_tables
x_tables
binfmt_misc
bnep
bbswitch(O)
rtsx_usb_ms
memstick
ecb
btusb
uvcvideo
videobuf2_vmalloc
videobuf2_memops
bluetooth
videobuf2_core
v4l2_common
6lowpan_iphc
videodev
media
arc4
joydev
iTCO_wdt
iTCO_vendor_support
iwlmvm
mac80211
asus_nb_wmi
x86_pkg_temp_thermal
asus_wmi
sparse_keymap
snd_hda_codec_hdmi
intel_powerclamp
intel_rapl
coretemp
snd_hda_codec_realtek
snd_hda_codec_generic
kvm_intel
kvm
iwlwifi
snd_hda_intel
snd_hda_controller
snd_hda_codec
snd_hwdep
snd_pcm
cfg80211
psmouse
snd_timer
i2c_i801
pcspkr
snd
serio_raw
rfkill
soundcore
mei_me
mei
shpchp
lpc_ich
battery
evdev
processor
ac
cuse
fuse
parport_pc
ppdev
lp
parport
autofs4
ext4
crc16
mbcache
jbd2
algif_skcipher
af_alg
hid_generic
hid_cherry
usbhid
hid
dm_crypt
dm_mod
rtsx_usb_sdmmc
mmc_core
rtsx_usb
mfd_core
sg
sd_mod
crc_t10dif
crct10dif_generic
i915
mxm_wmi
crct10dif_pclmul
crct10dif_common
crc32_pclmul
crc32c_intel
ghash_clmulni_intel
aesni_intel
aes_x86_64
lrw
gf128mul
glue_helper
ablk_helper
cryptd
ahci
libahci
xhci_hcd
libata
ehci_pci
i2c_algo_bit
ehci_hcd
drm_kms_helper
scsi_mod
r8169
mii
drm
usbcore
usb_common
i2c_core
thermal
wmi
video
thermal_sys
button
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 2nd Generation Core Processor Family DRAM Controller [8086:0104] (rev 09)
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:01.0 PCI bridge [0604]: Intel Corporation Xeon E3-1200/2nd Generation Core Processor Family PCI Express Root Port [8086:0101] (rev 09) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: db000000-dc0fffff
Prefetchable memory behind bridge: 00000000c0000000-00000000d1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller [8086:0126] (rev 09) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:212e]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 48
Region 0: Memory at dc400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at b0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at e000 [size=64]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 6 Series/C200 Series Chipset Family MEI Controller #1 [8086:1c3a] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 49
Region 0: Memory at df00a000 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
Kernel driver in use: mei_me
00:1a.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #2 [8086:1c2d] (rev 05) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at df008000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05)
Subsystem: ASUSTeK Computer Inc. Device [1043:1ac3]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 50
Region 0: Memory at df000000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 1 [8086:1c10] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: de600000-deffffff
Prefetchable memory behind bridge: 00000000d4200000-00000000d4bfffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 2 [8086:1c12] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 0000b000-0000bfff
Memory behind bridge: ddc00000-de5fffff
Prefetchable memory behind bridge: 00000000d3700000-00000000d40fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.3 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 4 [8086:1c16] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000a000-0000afff
Memory behind bridge: dd200000-ddbfffff
Prefetchable memory behind bridge: 00000000d2c00000-00000000d35fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.5 PCI bridge [0604]: Intel Corporation 6 Series/C200 Series Chipset Family PCI Express Root Port 6 [8086:1c1a] (rev b5) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: dc800000-dd1fffff
Prefetchable memory behind bridge: 00000000d2100000-00000000d2afffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 6 Series/C200 Series Chipset Family USB Enhanced Host Controller #1 [8086:1c26] (rev 05) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at df007000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge [0601]: Intel Corporation HM65 Express Chipset Family LPC Controller [8086:1c49] (rev 05)
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: lpc_ich
00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 47
Region 0: I/O ports at e0b0 [size=8]
Region 1: I/O ports at e0a0 [size=4]
Region 2: I/O ports at e090 [size=8]
Region 3: I/O ports at e080 [size=4]
Region 4: I/O ports at e060 [size=32]
Region 5: Memory at df006000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 6 Series/C200 Series Chipset Family SMBus Controller [8086:1c22] (rev 05)
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin C routed to IRQ 18
Region 0: Memory at df005000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at e040 [size=32]
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF108M [GeForce GT 630M] [10de:0de9] (rev ff) (prog-if ff)
!!! Unknown header type 7f
03:00.0 Network controller [0280]: Intel Corporation Wireless 7260 [8086:08b1] (rev 73)
Subsystem: Intel Corporation Dual Band Wireless-AC 7260 [8086:4070]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 51
Region 0: Memory at ddc00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: <access denied>
Kernel driver in use: iwlwifi
04:00.0 USB controller [0c03]: ASMedia Technology Inc. ASM1042 SuperSpeed USB Host Controller [1b21:1042] (prog-if 30 [XHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:1059]
Control: I/O- Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 19
Region 0: Memory at dd200000 (64-bit, non-prefetchable) [size=32K]
Capabilities: <access denied>
Kernel driver in use: xhci_hcd
05:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 06)
Subsystem: ASUSTeK Computer Inc. Device [1043:1277]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 41
Region 0: I/O ports at 9000 [size=256]
Region 2: Memory at d2104000 (64-bit, prefetchable) [size=4K]
Region 4: Memory at d2100000 (64-bit, prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: r8169
** USB devices:
Bus 004 Device 005: ID 046d:c069 Logitech, Inc. M500 Laser Mouse
Bus 004 Device 004: ID 046a:0023 Cherry GmbH CyMotion Master Linux Keyboard G230
Bus 004 Device 003: ID 0424:2514 Standard Microsystems Corp. USB 2.0 Hub
Bus 004 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 004 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 005: ID 0bda:0139 Realtek Semiconductor Corp. RTS5139 Card Reader Controller
Bus 001 Device 004: ID 13d3:5710 IMC Networks UVC VGA Webcam
Bus 001 Device 003: ID 8087:07dc Intel Corp.
Bus 001 Device 002: ID 8087:0024 Intel Corp. Integrated Rate Matching Hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
-- System Information:
Debian Release: 8.0
APT prefers testing
APT policy: (990, 'testing'), (100, 'unstable')
Architecture: amd64 (x86_64)
Foreign Architectures: i386
Kernel: Linux 3.16.0-4-amd64 (SMP w/4 CPU cores)
Locale: LANG=de_DE.utf8, LC_CTYPE=de_DE.utf8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Init: systemd (via /run/systemd/system)
Versions of packages linux-image-3.16.0-4-amd64 depends on:
ii debconf [debconf-2.0] 1.5.56
ii initramfs-tools [linux-initramfs-tool] 0.119
ii kmod 18-3
ii linux-base 3.5
ii module-init-tools 18-3
Versions of packages linux-image-3.16.0-4-amd64 recommends:
ii firmware-linux-free 3.3
ii irqbalance 1.0.6-3
Versions of packages linux-image-3.16.0-4-amd64 suggests:
pn debian-kernel-handbook <none>
ii grub-pc 2.02~beta2-22
pn linux-doc-3.16 <none>
Versions of packages linux-image-3.16.0-4-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
ii firmware-iwlwifi 0.43
pn firmware-libertas <none>
ii firmware-linux 0.43
ii firmware-linux-nonfree 0.43
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
ii firmware-realtek 0.43
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.16.0-4-amd64/postinst/mips-initrd-3.16.0-4-amd64:
linux-image-3.16.0-4-amd64/prerm/removing-running-kernel-3.16.0-4-amd64: true
linux-image-3.16.0-4-amd64/postinst/depmod-error-initrd-3.16.0-4-amd64: false
Reply to: