Bug#687478: linux-image-3.2.0-3-amd64: Xorg (at least gdm) doesn't detect keyboard and mouse
Package: src:linux
Version: 3.2.23-1
Severity: normal
Dear Maintainer,
Booting with 3.2.0-2-amd64 version keyboard and mouse are detected by Xorg.
Booting with 3.2.0-3-amd64 version keyboard and mouse are NOT detected
by Xorg. I have to unplug and plug both devices to Xorg detect it.
Dmesg when I attach keyboard / mouse is:
[ 577.000046] usb 3-1: USB disconnect, device number 2
[ 578.480032] usb 3-1: new low-speed USB device number 4 using uhci_hcd
[ 578.654419] usb 3-1: New USB device found, idVendor=413c, idProduct=3012
[ 578.654424] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 578.654428] usb 3-1: Product: Dell USB Optical Mouse
[ 578.654431] usb 3-1: Manufacturer: Dell
[ 578.670685] input: Dell Dell USB Optical Mouse as
/devices/pci0000:00/0000:00:1a.0/usb3/3-1/3-1:1.0/input/input10
[ 578.670851] generic-usb 0003:413C:3012.0003: input,hidraw0: USB HID
v1.11 Mouse [Dell Dell USB Optical Mouse] on usb-0000:00:1a.0-1/input0
[ 591.880049] usb 3-2: USB disconnect, device number 3
[ 593.856027] usb 3-2: new low-speed USB device number 5 using uhci_hcd
[ 594.030434] usb 3-2: New USB device found, idVendor=03f0, idProduct=0024
[ 594.030439] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 594.030443] usb 3-2: Product: HP Basic USB Keyboard
[ 594.030446] usb 3-2: Manufacturer: CHICONY
[ 594.048794] input: CHICONY HP Basic USB Keyboard as
/devices/pci0000:00/0000:00:1a.0/usb3/3-2/3-2:1.0/input/input11
[ 594.048998] generic-usb 0003:03F0:0024.0004: input,hidraw1: USB HID
v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on
usb-0000:00:1a.0-2/input0
Thank you very much
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: Hewlett-Packard
product_name: HP Compaq dc7700p Ultra-slim Desktop
product_version:
chassis_vendor: Hewlett-Packard
chassis_version:
bios_vendor: Hewlett-Packard
bios_version: 786E1 v02.09
board_vendor: Hewlett-Packard
board_name: 0A5Ch
board_version:
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation 82Q963/Q965 Memory
Controller Hub [8086:2990] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation
82Q963/Q965 Integrated Graphics Controller [8086:2992] (rev 02)
(prog-if 00 [VGA controller])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 42
Region 0: Memory at f0400000 (32-bit, non-prefetchable) [size=1M]
Region 2: Memory at e0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 1210 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:03.0 Communication controller [0780]: Intel Corporation 82Q963/Q965
HECI Controller [8086:2994] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx+
Latency: 0
Interrupt: pin A routed to IRQ 5
Region 0: Memory at f0526900 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:03.2 IDE interface [0101]: Intel Corporation 82Q963/Q965 PT IDER
Controller [8086:2996] (rev 02) (prog-if 85 [Master SecO PriO])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 0: I/O ports at 1218 [size=8]
Region 1: I/O ports at 1240 [size=4]
Region 2: I/O ports at 1220 [size=8]
Region 3: I/O ports at 1244 [size=4]
Region 4: I/O ports at 11e0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_generic
00:03.3 Serial controller [0700]: Intel Corporation 82Q963/Q965 KT
Controller [8086:2997] (rev 02) (prog-if 02 [16550])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 17
Region 0: I/O ports at 1228 [size=8]
Region 1: Memory at f0524000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: serial
00:19.0 Ethernet controller [0200]: Intel Corporation 82566DM Gigabit
Network Connection [8086:104a] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2800]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: Memory at f0500000 (32-bit, non-prefetchable) [size=128K]
Region 1: Memory at f0525000 (32-bit, non-prefetchable) [size=4K]
Region 2: I/O ports at 1100 [size=32]
Capabilities: <access denied>
Kernel driver in use: e1000e
00:1a.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI Controller #4 [8086:2834] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1120 [size=32]
Kernel driver in use: uhci_hcd
00:1a.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI Controller #5 [8086:2835] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1140 [size=32]
Kernel driver in use: uhci_hcd
00:1a.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB2 EHCI Controller #2 [8086:283a] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 22
Region 0: Memory at f0526000 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 82801H (ICH8 Family) HD
Audio Controller [8086:284b] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 43
Region 0: Memory at f0520000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801H (ICH8 Family) PCI
Express Port 1 [8086:283f] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=20, subordinate=20, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: c0000000-c01fffff
Prefetchable memory behind bridge: 00000000c0200000-00000000c03fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI Controller #1 [8086:2830] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 4: I/O ports at 1160 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB UHCI Controller #2 [8086:2831] (rev 02) (prog-if 00 [UHCI])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 21
Region 4: I/O ports at 1180 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB controller [0c03]: Intel Corporation 82801H (ICH8 Family)
USB2 EHCI Controller #1 [8086:2836] (rev 02) (prog-if 20 [EHCI])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 20
Region 0: Memory at f0526400 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 PCI Bridge
[8086:244e] (rev f2) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=07, subordinate=07, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801HO (ICH8DO) LPC
Interface Controller [8086:2814] (rev 02)
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 IDE interface [0101]: Intel Corporation 82801H (ICH8 Family) 4
port SATA Controller [IDE mode] [8086:2820] (rev 02) (prog-if 8a
[Master SecP PriP])
Subsystem: Hewlett-Packard Company Device [103c:2803]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 11f0 [size=16]
Region 5: I/O ports at 1200 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 005 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 006 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 002: ID 413c:3012 Dell Computer Corp. Optical Wheel Mouse
Bus 003 Device 003: ID 03f0:0024 Hewlett-Packard KU-0316 Keyboard
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable'), (500, 'testing'), (1, 'experimental')
Architecture: amd64 (x86_64)
Kernel: Linux 3.2.0-2-amd64 (SMP w/2 CPU cores)
Locale: LANG=es_ES.UTF-8, LC_CTYPE=es_ES.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-3-amd64 depends on:
ii debconf [debconf-2.0] 1.5.46
ii initramfs-tools [linux-initramfs-tool] 0.107
ii kmod 9-2
ii linux-base 3.5
ii module-init-tools 9-2
Versions of packages linux-image-3.2.0-3-amd64 recommends:
ii firmware-linux-free 3.1
Versions of packages linux-image-3.2.0-3-amd64 suggests:
ii debian-kernel-handbook 1.0.15
ii grub-pc 1.99-22.1
ii linux-doc-3.2 3.2.23-1
Versions of packages linux-image-3.2.0-3-amd64 is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
linux-image-3.2.0-3-amd64/postinst/depmod-error-initrd-3.2.0-3-amd64: false
linux-image-3.2.0-3-amd64/prerm/removing-running-kernel-3.2.0-3-amd64: true
linux-image-3.2.0-3-amd64/postinst/ignoring-ramdisk:
linux-image-3.2.0-3-amd64/postinst/missing-firmware-3.2.0-3-amd64:
Reply to: