Bug#687308: linux-image-3.2.0-2-686-pae: When insert usb yota lte modem or usb mouse both devices failed to work.
Package: src:linux
Version: 3.2.20-1
Severity: important
Dear Maintainer,
Sometimes when I insert device, both of them fail to work.
The only solution is to reboot laptop, which is bad.
Last line in dmesg are:
Sep 11 21:34:08 localhost kernel: [18653.975474] usb 2-1.2: new low-speed USB
device number 8 using ehci_hcd
Sep 11 21:34:08 localhost kernel: [18654.072262] usb 2-1.2: New USB device
found, idVendor=045e, idProduct=00cb
Sep 11 21:34:08 localhost kernel: [18654.072268] usb 2-1.2: New USB device
strings: Mfr=1, Product=2, SerialNumber=0
Sep 11 21:34:08 localhost kernel: [18654.072273] usb 2-1.2: Product: Microsoft
Basic Optical Mouse v2.0
Sep 11 21:34:08 localhost kernel: [18654.072276] usb 2-1.2: Manufacturer:
Microsoft
Sep 11 21:34:08 localhost kernel: [18654.076391] input: Microsoft Microsoft
Basic Optical Mouse v2.0 as
/devices/pci0000:00/0000:00:1d.0/usb2/2-1/2-1.2/2-1.2:1.0/input/input16
Sep 11 21:34:08 localhost kernel: [18654.076793] generic-usb
0003:045E:00CB.0002: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft
Basic Optical Mouse v2.0 ] on usb-0000:00:1d.0-1.2/input0
Sep 11 21:35:09 localhost kernel: [18714.942458] usb 2-1.3: USB disconnect,
device number 5
Sep 11 21:35:09 localhost kernel: [18714.942585] rndis_host 2-1.3:1.0: eth1:
unregister 'rndis_host' usb-0000:00:1d.0-1.3, RNDIS device
Sep 11 21:35:11 localhost kernel: [18717.048667] usb 2-1.3: new high-speed USB
device number 9 using ehci_hcd
Sep 11 21:35:11 localhost kernel: [18717.152258] ehci_hcd 0000:00:1d.0: fatal
error
Sep 11 21:35:11 localhost kernel: [18717.156193] ehci_hcd 0000:00:1d.0: HC
died; cleaning up
Sep 11 21:35:11 localhost kernel: [18717.159056] ehci_hcd 0000:00:1d.0: force
halt; handshake f8224824 00004000 00004000 -> -110
Sep 11 21:35:11 localhost kernel: [18717.159060] ehci_hcd 0000:00:1d.0: HC
died; cleaning up
Sep 11 21:35:11 localhost kernel: [18717.159156] usb 2-1.3: device descriptor
read/all, error -108
Sep 11 21:35:11 localhost kernel: [18717.159165] hub 2-1:1.0: cannot disable
port 3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159180] hub 2-1:1.0: cannot reset port
3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159187] hub 2-1:1.0: cannot disable
port 3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159198] hub 2-1:1.0: cannot reset port
3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159205] hub 2-1:1.0: cannot disable
port 3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159216] hub 2-1:1.0: cannot reset port
3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159222] hub 2-1:1.0: cannot disable
port 3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159228] hub 2-1:1.0: unable to
enumerate USB device on port 3
Sep 11 21:35:11 localhost kernel: [18717.159234] hub 2-1:1.0: cannot disable
port 3 (err = -19)
Sep 11 21:35:11 localhost kernel: [18717.159245] usb 2-1.2: USB disconnect,
device number 8
Sep 11 21:35:11 localhost kernel: [18717.288370] usb 2-1.6: USB disconnect,
device number 3
Sep 11 21:35:11 localhost kernel: [18717.340275] usb 2-1: USB disconnect,
device number 2
-- Package-specific info:
** Version:
Linux version 3.2.0-2-686-pae (Debian 3.2.20-1) (debian-kernel@lists.debian.org) (gcc version 4.6.3 (Debian 4.6.3-7) ) #1 SMP Mon Jun 11 18:27:04 UTC 2012
** Command line:
BOOT_IMAGE=/boot/vmlinuz-3.2.0-2-686-pae root=UUID=2df64c86-d83f-4dba-800d-699a1b3bb259 ro quiet
** Tainted: O (4096)
* Out-of-tree module has been loaded.
** Kernel log:
[ 9.536006] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PROM
[ 9.536016] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[ 9.536018] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from PCIROM
[ 9.545817] nouveau 0000:01:00.0: Invalid ROM contents
[ 9.545909] [drm] nouveau 0000:01:00.0: ... BIOS signature not found
[ 9.545912] [drm] nouveau 0000:01:00.0: Attempting to load BIOS image from ACPI
[ 10.074032] input: FSPPS/2 Sentelic FingerSensingPad as /devices/platform/i8042/serio1/input/input14
[ 13.289958] [drm] nouveau 0000:01:00.0: ... appears to be valid
[ 13.289962] [drm] nouveau 0000:01:00.0: BIT BIOS found
[ 13.289965] [drm] nouveau 0000:01:00.0: Bios version 70.08.19.00
[ 13.289969] [drm] nouveau 0000:01:00.0: TMDS table version 2.0
[ 13.289971] [drm] nouveau 0000:01:00.0: Found Display Configuration Block version 4.0
[ 13.289974] [drm] nouveau 0000:01:00.0: Raw DCB entry 0: 02014300 00000000
[ 13.289976] [drm] nouveau 0000:01:00.0: Raw DCB entry 1: 0000000e 00000000
[ 13.289979] [drm] nouveau 0000:01:00.0: DCB connector table: VHER 0x40 5 16 4
[ 13.289981] [drm] nouveau 0000:01:00.0: 0: 0x00000340: type 0x40 idx 0 tag 0xff
[ 13.289983] [drm] nouveau 0000:01:00.0: 1: 0x00001061: type 0x61 idx 1 tag 0x07
[ 13.289985] [drm] nouveau 0000:01:00.0: 2: 0x00000147: type 0x47 idx 2 tag 0xff
[ 13.289987] [drm] nouveau 0000:01:00.0: 3: 0x00202346: type 0x46 idx 3 tag 0x08
[ 13.289989] [drm] nouveau 0000:01:00.0: 4: 0x00000400: type 0x00 idx 4 tag 0xff
[ 13.289991] [drm] nouveau 0000:01:00.0: 5: 0x00000210: type 0x10 idx 5 tag 0xff
[ 13.289993] [drm] nouveau 0000:01:00.0: 6: 0x00000211: type 0x11 idx 6 tag 0xff
[ 13.289995] [drm] nouveau 0000:01:00.0: 7: 0x00000213: type 0x13 idx 7 tag 0xff
[ 13.290009] [drm] nouveau 0000:01:00.0: Adaptor not initialised, running VBIOS init tables.
[ 13.290011] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 0 at offset 0xD2F9
[ 13.314046] [drm] nouveau 0000:01:00.0: 0xD2E4: i2c wr fail: -6
[ 13.354221] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 1 at offset 0xD93F
[ 13.381034] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 2 at offset 0xEAD4
[ 13.381040] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 3 at offset 0xEAD8
[ 13.381098] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table 4 at offset 0xEBC0
[ 13.381100] [drm] nouveau 0000:01:00.0: Parsing VBIOS init table at offset 0xEC25
[ 13.419826] [drm] nouveau 0000:01:00.0: 3 available performance level(s)
[ 13.419829] [drm] nouveau 0000:01:00.0: 0: core 50MHz shader 101MHz memory 135MHz timing 0 voltage 830mV
[ 13.419832] [drm] nouveau 0000:01:00.0: 1: core 202MHz shader 405MHz memory 324MHz timing 1 voltage 830mV
[ 13.419835] [drm] nouveau 0000:01:00.0: 3: core 560MHz shader 1120MHz memory 800MHz timing 2 voltage 900mV
[ 13.419925] [drm] nouveau 0000:01:00.0: c: core 202MHz shader 405MHz memory 324MHz voltage 950mV
[ 13.426280] [TTM] Zone kernel: Available graphics memory: 430362 kiB.
[ 13.426285] [TTM] Zone highmem: Available graphics memory: 1968542 kiB.
[ 13.426289] [TTM] Initializing pool allocator.
[ 13.426306] [drm] nouveau 0000:01:00.0: Detected 512MiB VRAM
[ 13.426317] mtrr: no more MTRRs available
[ 13.426337] [drm] nouveau 0000:01:00.0: 512 MiB GART (aperture)
[ 13.437848] [drm] nouveau 0000:01:00.0: ACPI backlight interface available, not registering our own
[ 13.486008] [drm] Supports vblank timestamp caching Rev 1 (10.10.2010).
[ 13.486010] [drm] No driver support for vblank timestamp query.
[ 13.535412] [drm] nouveau 0000:01:00.0: allocated 1024x768 fb: 0x1a0000, bo f7144600
[ 13.535523] fb1: nouveaufb frame buffer device
[ 13.535527] [drm] Initialized nouveau 0.0.16 20090420 for 0000:01:00.0 on minor 1
[ 13.772836] usb 2-1.3: new high-speed USB device number 5 using ehci_hcd
[ 13.865826] usb 2-1.3: New USB device found, idVendor=1076, idProduct=8001
[ 13.865833] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 13.865837] usb 2-1.3: Product: Modem Yota
[ 13.865841] usb 2-1.3: Manufacturer: GCT SEMICONDUCTOR Inc
[ 13.910892] usbcore: registered new interface driver uas
[ 13.922727] Initializing USB Mass Storage driver...
[ 13.922815] scsi6 : usb-storage 2-1.3:1.0
[ 13.922877] usbcore: registered new interface driver usb-storage
[ 13.922879] USB Mass Storage support registered.
[ 13.932297] intel ips 0000:00:1f.6: i915 driver attached, reenabling gpu turbo
[ 14.127987] Adding 3949564k swap on /dev/sda7. Priority:-1 extents:1 across:3949564k
[ 14.147657] EXT4-fs (sda5): re-mounted. Opts: (null)
[ 14.507404] EXT4-fs (sda5): re-mounted. Opts: errors=remount-ro
[ 14.690866] loop: module loaded
[ 14.918574] scsi 6:0:0:0: CD-ROM GDM Mass PQ: 0 ANSI: 0 CCS
[ 14.942975] sr1: scsi3-mmc drive: 0x/0x caddy
[ 14.943184] sr 6:0:0:0: Attached scsi CD-ROM sr1
[ 14.943935] sr 6:0:0:0: Attached scsi generic sg2 type 5
[ 15.755680] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 15.870513] usb 2-1.3: USB disconnect, device number 5
[ 16.833480] usb 2-1.3: new high-speed USB device number 6 using ehci_hcd
[ 16.930608] usb 2-1.3: New USB device found, idVendor=1076, idProduct=8002
[ 16.930614] usb 2-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 16.930618] usb 2-1.3: Product: Modem Yota
[ 16.930622] usb 2-1.3: Manufacturer: GCT SEMICONDUCTOR Inc
[ 17.062252] usbcore: registered new interface driver cdc_ether
[ 17.066533] rndis_host 2-1.3:1.0: dev can't take 1558 byte packets (max 1458), adjusting MTU to 1400
[ 17.068314] rndis_host 2-1.3:1.0: eth1: register 'rndis_host' at usb-0000:00:1d.0-1.3, RNDIS device, 00:09:3b:f0:1a:40
[ 17.068328] usbcore: registered new interface driver rndis_host
[ 19.043447] vboxdrv: Found 4 processor cores.
[ 19.043559] vboxdrv: fAsync=0 offMin=0x127 offMax=0xdff
[ 19.043606] vboxdrv: TSC mode is 'synchronous', kernel timer mode is 'normal'.
[ 19.043607] vboxdrv: Successfully loaded version 4.1.18_Debian (interface 0x00190000).
[ 19.784529] input: ACPI Virtual Keyboard Device as /devices/virtual/input/input15
[ 19.826118] vboxpci: IOMMU not found (not registered)
[ 23.256655] Bluetooth: Core ver 2.16
[ 23.256671] NET: Registered protocol family 31
[ 23.256672] Bluetooth: HCI device and connection manager initialized
[ 23.256674] Bluetooth: HCI socket layer initialized
[ 23.256675] Bluetooth: L2CAP socket layer initialized
[ 23.256679] Bluetooth: SCO socket layer initialized
[ 23.276458] Bluetooth: RFCOMM TTY layer initialized
[ 23.276470] Bluetooth: RFCOMM socket layer initialized
[ 23.276473] Bluetooth: RFCOMM ver 1.11
[ 23.348663] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 23.348666] Bluetooth: BNEP filters: protocol multicast
[ 24.257456] lp: driver loaded but no devices found
[ 24.453201] ppdev: user-space parallel port driver
[ 24.822871] atl1c 0000:03:00.0: irq 44 for MSI/MSI-X
[ 24.882667] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 35.863760] eth1: no IPv6 routers present
** Model information
not available
** Loaded modules:
parport_pc
ppdev
lp
parport
bnep
rfcomm
bluetooth
acpi_cpufreq
mperf
cpufreq_conservative
cpufreq_stats
cpufreq_userspace
cpufreq_powersave
pci_stub
vboxpci(O)
vboxnetadp(O)
vboxnetflt(O)
vboxdrv(O)
uinput
binfmt_misc
rndis_host
cdc_ether
usbnet
mii
loop
usb_storage
uas
rtl8192se
uvcvideo
rtlwifi
videodev
mac80211
nouveau
cfg80211
media
rfkill
iTCO_wdt
iTCO_vendor_support
i915
snd_hda_codec_hdmi
ttm
drm_kms_helper
snd_hda_codec_realtek
psmouse
drm
pcspkr
evdev
serio_raw
i2c_algo_bit
i2c_i801
intel_ips
i2c_core
mxm_wmi
battery
video
snd_hda_intel
snd_hda_codec
snd_hwdep
snd_pcm
snd_page_alloc
wmi
snd_seq
snd_seq_device
snd_timer
snd
soundcore
ac
power_supply
processor
button
ext4
crc16
jbd2
mbcache
usbhid
hid
sg
sd_mod
sr_mod
cdrom
crc_t10dif
ahci
libahci
libata
ehci_hcd
usbcore
scsi_mod
usb_common
atl1c
thermal
thermal_sys
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Core Processor DRAM Controller [8086:0044] (rev 02)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:01.0 PCI bridge [0604]: Intel Corporation Core Processor PCI Express x16 Root Port [8086:0045] (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00004000-00004fff
Memory behind bridge: d0000000-d10fffff
Prefetchable memory behind bridge: 00000000a0000000-00000000b1ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:02.0 VGA compatible controller [0300]: Intel Corporation Core Processor Integrated Graphics Controller [8086:0046] (rev 02) (prog-if 00 [VGA controller])
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 43
Region 0: Memory at d1400000 (64-bit, non-prefetchable) [size=4M]
Region 2: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 4: I/O ports at 5050 [size=8]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
Kernel driver in use: i915
00:16.0 Communication controller [0780]: Intel Corporation 5 Series/3400 Series Chipset HECI Controller [8086:3b64] (rev 06)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 10
Region 0: Memory at d7806100 (64-bit, non-prefetchable) [size=16]
Capabilities: <access denied>
00:1a.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b3c] (rev 05) (prog-if 20 [EHCI])
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d7805c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1b.0 Audio device [0403]: Intel Corporation 5 Series/3400 Series Chipset High Definition Audio [8086:3b56] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 42
Region 0: Memory at d7800000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: snd_hda_intel
00:1c.0 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 1 [8086:3b42] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: 00003000-00003fff
Memory behind bridge: d6800000-d77fffff
Prefetchable memory behind bridge: 00000000d1800000-00000000d27fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.1 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 2 [8086:3b44] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: 00002000-00002fff
Memory behind bridge: d5800000-d67fffff
Prefetchable memory behind bridge: 00000000d2800000-00000000d37fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1c.4 PCI bridge [0604]: Intel Corporation 5 Series/3400 Series Chipset PCI Express Root Port 5 [8086:3b4a] (rev 05) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=09, subordinate=0b, sec-latency=0
I/O behind bridge: 00001000-00001fff
Memory behind bridge: d4800000-d57fffff
Prefetchable memory behind bridge: 00000000d3800000-00000000d47fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport
00:1d.0 USB controller [0c03]: Intel Corporation 5 Series/3400 Series Chipset USB2 Enhanced Host Controller [8086:3b34] (rev 05) (prog-if 20 [EHCI])
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 21
Region 0: Memory at d7805800 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev a5) (prog-if 01 [Subtractive decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=04, subordinate=04, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation Mobile 5 Series Chipset LPC Interface Controller [8086:3b09] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
00:1f.2 SATA controller [0106]: Intel Corporation 5 Series/3400 Series Chipset 4 port SATA AHCI Controller [8086:3b29] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 41
Region 0: I/O ports at 5048 [size=8]
Region 1: I/O ports at 505c [size=4]
Region 2: I/O ports at 5040 [size=8]
Region 3: I/O ports at 5058 [size=4]
Region 4: I/O ports at 5020 [size=32]
Region 5: Memory at d7805000 (32-bit, non-prefetchable) [size=2K]
Capabilities: <access denied>
Kernel driver in use: ahci
00:1f.3 SMBus [0c05]: Intel Corporation 5 Series/3400 Series Chipset SMBus Controller [8086:3b30] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d7806000 (64-bit, non-prefetchable) [size=256]
Region 4: I/O ports at 5000 [size=32]
00:1f.6 Signal processing controller [1180]: Intel Corporation 5 Series/3400 Series Chipset Thermal Subsystem [8086:3b32] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: Memory at d7804000 (64-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: intel ips
01:00.0 VGA compatible controller [0300]: NVIDIA Corporation GF108 [GeForce GT 425M] [10de:0df0] (rev a1) (prog-if 00 [VGA controller])
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at d0000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at a0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at b0000000 (64-bit, prefetchable) [size=32M]
Region 5: I/O ports at 4000 [size=128]
Expansion ROM at d1000000 [disabled] [size=512K]
Capabilities: <access denied>
Kernel driver in use: nouveau
02:00.0 Network controller [0280]: Realtek Semiconductor Co., Ltd. RTL8191SEvB Wireless LAN Controller [10ec:8172] (rev 10)
Subsystem: Quanta Microsystems, Inc Device [1a32:0308]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
Region 0: I/O ports at 3000 [size=256]
Region 1: Memory at d6800000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
03:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR8131 Gigabit Ethernet [1969:1063] (rev c0)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Interrupt: pin A routed to IRQ 44
Region 0: Memory at d5800000 (64-bit, non-prefetchable) [size=256K]
Region 2: I/O ports at 2000 [size=128]
Capabilities: <access denied>
Kernel driver in use: atl1c
ff:00.0 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture Generic Non-core Registers [8086:2c62] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:00.1 Host bridge [0600]: Intel Corporation Core Processor QuickPath Architecture System Address Decoder [8086:2d01] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.0 Host bridge [0600]: Intel Corporation Core Processor QPI Link 0 [8086:2d10] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.1 Host bridge [0600]: Intel Corporation Core Processor QPI Physical 0 [8086:2d11] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.2 Host bridge [0600]: Intel Corporation Core Processor Reserved [8086:2d12] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
ff:02.3 Host bridge [0600]: Intel Corporation Core Processor Reserved [8086:2d13] (rev 05)
Subsystem: QUANTA Computer Inc Device [152d:0853]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 001 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 002: ID 8087:0020 Intel Corp. Integrated Rate Matching Hub
Bus 002 Device 003: ID 045e:00cb Microsoft Corp. Basic Optical Mouse v2.0
Bus 002 Device 004: ID 064e:c206 Suyin Corp.
Bus 002 Device 006: ID 1076:8002 GCT Semiconductor, Inc.
-- System Information:
Debian Release: wheezy/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 3.2.0-2-686-pae (SMP w/4 CPU cores)
Locale: LANG=ru_RU.UTF-8, LC_CTYPE=ru_RU.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.2.0-2-686-pae depends on:
ii debconf [debconf-2.0] 1.5.46
ii initramfs-tools [linux-initramfs-tool] 0.107
ii kmod 9-1
ii linux-base 3.5
ii module-init-tools 9-1
Versions of packages linux-image-3.2.0-2-686-pae recommends:
ii firmware-linux-free 3.1
ii libc6-i686 2.13-35
Versions of packages linux-image-3.2.0-2-686-pae suggests:
ii extlinux 2:4.05+dfsg-6
ii grub-pc 1.99-22.1
ii linux-doc-3.2 3.2.23-1
Versions of packages linux-image-3.2.0-2-686-pae is related to:
pn firmware-atheros <none>
pn firmware-bnx2 <none>
pn firmware-bnx2x <none>
pn firmware-brcm80211 <none>
pn firmware-intelwimax <none>
pn firmware-ipw2x00 <none>
pn firmware-ivtv <none>
pn firmware-iwlwifi <none>
pn firmware-libertas <none>
pn firmware-linux <none>
pn firmware-linux-nonfree <none>
pn firmware-myricom <none>
pn firmware-netxen <none>
pn firmware-qlogic <none>
pn firmware-ralink <none>
pn firmware-realtek <none>
pn xen-hypervisor <none>
-- debconf information:
* linux-image-3.2.0-2-686-pae/prerm/removing-running-kernel-3.2.0-2-686-pae: true
linux-image-3.2.0-2-686-pae/postinst/depmod-error-initrd-3.2.0-2-686-pae: false
linux-image-3.2.0-2-686-pae/postinst/ignoring-ramdisk:
linux-image-3.2.0-2-686-pae/postinst/missing-firmware-3.2.0-2-686-pae:
Reply to: