Bug#635840: TP-Link TL-WN821N v2 doesn't work with kernel 3.0
Package: linux-2.6
Version: 3.0.0-1
Severity: normal
Tags: sid
I cannot raise up my wireless interface using kernel 3.0:
# ifconfig wlan0 up
wla0n: ERROR while getting interface flags: No such device
With kernel 2.6.39 I'm able to run the same command and get a stable connection
(using wpa_supplicant).
I've used ar9170usb module but now it was removed and replaced by carl9170
(http://linuxwireless.org/en/users/Drivers/ar9170)
# lsusb
Bus 001 Device 003: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N
v2 [Atheros AR9001U-(2)NG]
dmesg doesn't give any useful information about how my device was registered.
Thank you and sorry about my english.
-- Package-specific info:
** Kernel log: boot messages should be attached
** Model information
sys_vendor: OEM
product_name:
product_version:
chassis_vendor: OEM
chassis_version:
bios_vendor: OEM
bios_version: 1.09
board_vendor: OEM
board_name: N/A
board_version: N/A
** Network interface configuration:
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface
auto lo
iface lo inet loopback
** PCI devices:
00:00.0 Host bridge [0600]: Silicon Integrated Systems [SiS] 671MX [1039:0671]
Subsystem: Elitegroup Computer Systems Device [1019:5050]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 32
Region 0: Memory at a0000000 (32-bit, non-prefetchable) [size=256M]
Capabilities: <access denied>
Kernel driver in use: agpgart-sis
00:01.0 PCI bridge [0604]: Silicon Integrated Systems [SiS] SiS AGP Port (virtual PCI-to-PCI bridge) [1039:0003] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 00009000-00009fff
Memory behind bridge: b0000000-b00fffff
Prefetchable memory behind bridge: c0000000-cfffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR- NoISA+ VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
00:02.0 ISA bridge [0601]: Silicon Integrated Systems [SiS] SiS968 [MuTIOL Media IO] [1039:0968] (rev 01)
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:02.5 IDE interface [0101]: Silicon Integrated Systems [SiS] 5513 [IDE] [1039:5513] (rev 01) (prog-if 80 [Master])
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 128
Interrupt: pin ? routed to IRQ 16
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at 1080 [size=16]
Capabilities: <access denied>
Kernel driver in use: pata_sis
00:03.0 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max)
Interrupt: pin A routed to IRQ 20
Region 0: Memory at b0104000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:03.1 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 1.1 Controller [1039:7001] (rev 0f) (prog-if 10 [OHCI])
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max)
Interrupt: pin B routed to IRQ 21
Region 0: Memory at b0105000 (32-bit, non-prefetchable) [size=4K]
Kernel driver in use: ohci_hcd
00:03.3 USB Controller [0c03]: Silicon Integrated Systems [SiS] USB 2.0 Controller [1039:7002] (prog-if 20 [EHCI])
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32 (20000ns max)
Interrupt: pin C routed to IRQ 22
Region 0: Memory at b0106000 (32-bit, non-prefetchable) [size=4K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:04.0 Ethernet controller [0200]: Silicon Integrated Systems [SiS] 191 Gigabit Ethernet Adapter [1039:0191] (rev 02)
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at b0307000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 1000 [size=128]
Capabilities: <access denied>
Kernel driver in use: sis190
00:05.0 IDE interface [0101]: Silicon Integrated Systems [SiS] SATA Controller / IDE mode [1039:1183] (rev 03) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Silicon Integrated Systems [SiS] SATA Controller / IDE mode [1039:1183]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 32
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at 10c8 [size=8]
Region 1: I/O ports at 10bc [size=4]
Region 2: I/O ports at 10c0 [size=8]
Region 3: I/O ports at 10b8 [size=4]
Region 4: I/O ports at 10a0 [size=16]
Capabilities: <access denied>
Kernel driver in use: sata_sis
00:0f.0 Audio device [0403]: Silicon Integrated Systems [SiS] Azalia Audio Controller [1039:7502]
Subsystem: Elitegroup Computer Systems Device [1019:5a00]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (13000ns min, 2750ns max)
Interrupt: pin A routed to IRQ 18
Region 0: Memory at b0100000 (32-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
01:00.0 VGA compatible controller [0300]: Silicon Integrated Systems [SiS] 771/671 PCIE VGA Display Adapter [1039:6351] (rev 10) (prog-if 00 [VGA controller])
Subsystem: Elitegroup Computer Systems Device [1019:5050]
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 16
BIST result: 00
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=256M]
Region 1: Memory at b0000000 (32-bit, non-prefetchable) [size=128K]
Region 2: I/O ports at 9000 [size=128]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0cf3:1002 Atheros Communications, Inc. TP-Link TL-WN821N v2 [Atheros AR9001U-(2)NG]
Bus 001 Device 004: ID 0bda:0158 Realtek Semiconductor Corp. USB 2.0 multicard reader
Bus 003 Device 002: ID 093a:2510 Pixart Imaging, Inc. Optical Mouse
Bus 003 Device 003: ID 0c10:0000
-- System Information:
Debian Release: wheezy/sid
APT prefers unstable
APT policy: (500, 'unstable')
Architecture: amd64 (x86_64)
Kernel: Linux 2.6.39-2-amd64 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-3.0.0-1-amd64 depends on:
ii debconf [debconf-2.0] 1.5.40 Debian configuration management sy
ii initramfs-tools [linux-initra 0.99 tools for generating an initramfs
ii linux-base 3.3 Linux image base package
ii module-init-tools 3.16-1 tools for managing Linux kernel mo
Versions of packages linux-image-3.0.0-1-amd64 recommends:
ii firmware-linux-free 3 Binary firmware for various driver
Versions of packages linux-image-3.0.0-1-amd64 suggests:
ii grub-pc 1.99-9 GRand Unified Bootloader, version
pn linux-doc-3.0.0 <none> (no description available)
Versions of packages linux-image-3.0.0-1-amd64 is related to:
pn firmware-bnx2 <none> (no description available)
pn firmware-bnx2x <none> (no description available)
pn firmware-ipw2x00 <none> (no description available)
pn firmware-ivtv <none> (no description available)
pn firmware-iwlwifi <none> (no description available)
pn firmware-linux <none> (no description available)
pn firmware-linux-nonfree <none> (no description available)
pn firmware-qlogic <none> (no description available)
pn firmware-ralink <none> (no description available)
pn xen-hypervisor <none> (no description available)
-- debconf information:
linux-image-3.0.0-1-amd64/postinst/ignoring-ramdisk:
linux-image-3.0.0-1-amd64/prerm/removing-running-kernel-3.0.0-1-amd64: true
linux-image-3.0.0-1-amd64/postinst/missing-firmware-3.0.0-1-amd64:
linux-image-3.0.0-1-amd64/postinst/depmod-error-initrd-3.0.0-1-amd64: false
Reply to: