[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

Bug#622833: linux-image-2.6.38-2-686: kernel panic in mac80211



Package: linux-2.6
Version: 2.6.38-3
Severity: critical
Justification: breaks the whole system

Booting panics when bringing interfaces up, including a Wi-Fi adm8211
from drivers/net/wireless.  The stack trace mentions
ieee80211_rx_handlers in mac80211, net_receive_skb, do_page_fault,
bad_area_nosemaphore, no_context (from the least to the most recently
called).

I will send screenshots of the trace.

-- Package-specific info:
** Kernel log: boot messages should be attached

** Model information
not available

** Network interface configuration:



auto tp
iface tp inet static
	address 192.168.3.1
	netmask 255.255.255.0
	network 192.168.3.0
	broadcast 192.168.3.255

auto wl
iface wl inet static
	address 192.168.2.172
	netmask 255.255.255.0
	network 192.168.2.0
	broadcast 192.168.2.255
	gateway 192.168.2.1
	dns-nameservers 192.168.2.1
	wpa-ssid D3
	wpa-bsssid 00:21:91:F8:36:6E
wpa-psk *************
	up sleep 5; /sbin/iwconfig "${IFACE}"
	up /sbin/ip route add 224.0.0.0/4 dev "${IFACE}"

iface tun6to4 inet6 v4tunnel
	address $(printf "2002:%02x%02x:%02x%02x::1" \
                  $(printf "%s\r\n%s\r\n\r\n" \
                    "GET / HTTP/1.1" \
                    "Host: checkip.dyndns.org" \
                  | /bin/nc checkip.dyndns.org 80 \
                  | /bin/sed -ne 's/.*Address: \([.0-9]*\).*/\1/p' \
		  | tr '.' ' ') \
		)
	netmask 16
	endpoint 192.88.99.1
	local any
	ttl 64
	up /sbin/ip -6 route add 2000::/3 dev tun6to4
	down /sbin/ip -6 route flush dev tun6to4

auto lo
iface lo inet loopback


** PCI devices:
00:00.0 Host bridge [0600]: ATI Technologies Inc Radeon Xpress 200 Host Bridge [1002:5a33] (rev 01)
	Subsystem: ASUSTeK Computer Inc. Device [1043:819a]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 64
	Region 3: Memory at e0000000 (64-bit, non-prefetchable) [size=512M]

00:01.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 0000c000-0000cfff
	Memory behind bridge: c0000000-dfdfffff
	Prefetchable memory behind bridge: a0000000-afffffff
	Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
	BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [b0] Subsystem: ATI Technologies Inc RS480 PCI Bridge [1002:5a3f]

00:05.0 PCI bridge [0604]: ATI Technologies Inc RS480 PCI Bridge [1002:5a37] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
	Latency: 0, Cache Line Size: 64 bytes
	Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
	I/O behind bridge: 0000d000-0000dfff
	Memory behind bridge: dfe00000-dfefffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [50] Power Management version 3
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Express (v1) Root Port (Slot-), MSI 00
		DevCap:	MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
			ExtTag+ RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 128 bytes
		DevSta:	CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
		LnkCap:	Port #2, Speed 2.5GT/s, Width x2, ASPM L0s L1, Latency L0 <64ns, L1 <1us
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
		RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
		RootCap: CRSVisible-
		RootSta: PME ReqID 0000, PMEStatus- PMEPending-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Capabilities: [b0] Subsystem: ATI Technologies Inc Device [1002:5a33]
	Capabilities: [b8] HyperTransport: MSI Mapping Enable+ Fixed+
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		AERCap:	First Error Pointer: 00, GenCap- CGenEn- ChkCap- ChkEn-
	Capabilities: [140 v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Kernel driver in use: pcieport

00:1a.0 PCI bridge [0604]: ALi Corporation M5249 HTT to PCI Bridge [10b9:5249] (prog-if 00 [Normal decode])
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
	Latency: 0
	Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: dff00000-dfffffff
	Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- <SERR- <PERR-
	BridgeCtl: Parity+ SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
		PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
	Capabilities: [c0] HyperTransport: MSI Mapping Enable- Fixed-
		Mapping Address Base: 00000000fee00000

00:1c.0 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:8056]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (20000ns max), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: Memory at bfffc000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:1c.1 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:8056]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (20000ns max), Cache Line Size: 64 bytes
	Interrupt: pin B routed to IRQ 18
	Region 0: Memory at bfffd000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:1c.2 USB Controller [0c03]: ALi Corporation USB 1.1 Controller [10b9:5237] (rev 03) (prog-if 10 [OHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:8056]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (20000ns max), Cache Line Size: 64 bytes
	Interrupt: pin C routed to IRQ 19
	Region 0: Memory at bfffe000 (32-bit, non-prefetchable) [size=4K]
	Kernel driver in use: ohci_hcd

00:1c.3 USB Controller [0c03]: ALi Corporation USB 2.0 Controller [10b9:5239] (rev 01) (prog-if 20 [EHCI])
	Subsystem: ASUSTeK Computer Inc. Device [1043:8056]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (4000ns min, 8000ns max)
	Interrupt: pin D routed to IRQ 23
	Region 0: Memory at bffffc00 (32-bit, non-prefetchable) [size=256]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [58] Debug port: BAR=1 offset=0090
	Capabilities: [78] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Kernel driver in use: ehci_hcd

00:1d.0 Audio device [0403]: ALi Corporation High Definition Audio/AC'97 Host Controller [10b9:5461] (rev 02)
	Subsystem: ASUSTeK Computer Inc. Device [1043:81b3]
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (4000ns min, 20000ns max)
	Interrupt: pin C routed to IRQ 22
	Region 0: Memory at bfff8000 (32-bit, non-prefetchable) [size=16K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=55mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [60] MSI: Enable- Count=1/1 Maskable+ 64bit-
		Address: 00000000  Data: 0000
		Masking: 00000000  Pending: 00000000
	Kernel driver in use: HDA Intel

00:1e.0 ISA bridge [0601]: ALi Corporation M1575 South Bridge [10b9:1575]
	Subsystem: ALi Corporation M1575 South Bridge [10b9:1575]
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (250ns min, 6000ns max)

00:1e.1 Bridge [0680]: ALi Corporation M7101 Power Management Controller [PMU] [10b9:7101]
	Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-

00:1f.0 IDE interface [0101]: ALi Corporation M5229 IDE [10b9:5229] (rev c8) (prog-if 8a [Master SecP PriP])
	Subsystem: ASUSTeK Computer Inc. Device [1043:8056]
	Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 32
	Interrupt: pin A routed to IRQ 21
	Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
	Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
	Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
	Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
	Region 4: I/O ports at ff00 [size=16]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000
	Kernel driver in use: pata_ali

00:1f.1 SATA controller [0106]: ALi Corporation ULi M5288 SATA [10b9:5288] (rev 10) (prog-if 01 [AHCI 1.0])
	Subsystem: ASUSTeK Computer Inc. A8R-MVP Mainboard [1043:8056]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 128, Cache Line Size: 512 bytes
	Interrupt: pin A routed to IRQ 21
	Region 0: I/O ports at bc00 [size=16]
	Region 1: I/O ports at b880 [size=8]
	Region 2: I/O ports at b800 [size=16]
	Region 3: I/O ports at b480 [size=8]
	Region 4: I/O ports at b400 [size=32]
	Region 5: Memory at bffff800 (32-bit, non-prefetchable) [size=1K]
	Capabilities: [60] Power Management version 2
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [70] MSI: Enable- Count=1/1 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Kernel driver in use: ahci

01:05.0 VGA compatible controller [0300]: ATI Technologies Inc RC410 [Radeon Xpress 200] [1002:5a61] (prog-if 00 [VGA controller])
	Subsystem: ASUSTeK Computer Inc. Device [1043:819a]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (2000ns min), Cache Line Size: 64 bytes
	Interrupt: pin A routed to IRQ 11
	Region 0: Memory at a0000000 (32-bit, prefetchable) [size=128M]
	Region 1: I/O ports at c000 [size=256]
	Region 2: Memory at c0000000 (32-bit, non-prefetchable) [size=64K]
	Expansion ROM at dfde0000 [disabled] [size=128K]
	Capabilities: [50] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
		Address: 00000000  Data: 0000

02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168B PCI Express Gigabit Ethernet controller [10ec:8168] (rev 01)
	Subsystem: ASUSTeK Computer Inc. Device [1043:8168]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR+ <PERR- INTx-
	Latency: 0, Cache Line Size: 128 bytes
	Interrupt: pin A routed to IRQ 17
	Region 0: I/O ports at d800 [size=256]
	Region 2: Memory at dfeff000 (64-bit, non-prefetchable) [size=4K]
	Expansion ROM at dfee0000 [disabled] [size=8K]
	Capabilities: [40] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Capabilities: [48] Vital Product Data
		Unknown small resource type 05, will not decode more.
	Capabilities: [50] MSI: Enable- Count=1/2 Maskable- 64bit+
		Address: 0000000000000000  Data: 0000
	Capabilities: [60] Express (v1) Endpoint, MSI 00
		DevCap:	MaxPayload 1024 bytes, PhantFunc 0, Latency L0s unlimited, L1 unlimited
			ExtTag+ AttnBtn+ AttnInd+ PwrInd+ RBE- FLReset-
		DevCtl:	Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
			RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
			MaxPayload 128 bytes, MaxReadReq 4096 bytes
		DevSta:	CorrErr- UncorrErr+ FatalErr- UnsuppReq+ AuxPwr+ TransPend-
		LnkCap:	Port #0, Speed 2.5GT/s, Width x4, ASPM L0s, Latency L0 unlimited, L1 unlimited
			ClockPM- Surprise- LLActRep- BwNot-
		LnkCtl:	ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
			ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
		LnkSta:	Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
	Capabilities: [84] Vendor Specific Information: Len=4c <?>
	Capabilities: [100 v1] Advanced Error Reporting
		UESta:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq+ ACSViol-
		UEMsk:	DLP- SDES- TLP- FCP- CmpltTO- CmpltAbrt- UnxCmplt- RxOF- MalfTLP- ECRC- UnsupReq- ACSViol-
		UESvrt:	DLP+ SDES- TLP- FCP+ CmpltTO- CmpltAbrt- UnxCmplt- RxOF+ MalfTLP+ ECRC- UnsupReq- ACSViol-
		CESta:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		CEMsk:	RxErr- BadTLP- BadDLLP- Rollover- Timeout- NonFatalErr-
		AERCap:	First Error Pointer: 14, GenCap- CGenEn- ChkCap- ChkEn-
	Capabilities: [12c v1] Virtual Channel
		Caps:	LPEVC=0 RefClk=100ns PATEntryBits=1
		Arb:	Fixed- WRR32- WRR64- WRR128-
		Ctrl:	ArbSelect=Fixed
		Status:	InProgress-
		VC0:	Caps:	PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
			Arb:	Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
			Ctrl:	Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
			Status:	NegoPending- InProgress-
	Capabilities: [148 v1] Device Serial Number 01-00-00-00-10-ec-81-68
	Capabilities: [154 v1] Power Budgeting <?>
	Kernel driver in use: r8169

03:11.0 Network controller [0280]: ADMtek ADM8211 802.11b Wireless Interface [1317:8201] (rev 11)
	Subsystem: Standard Microsystems Corp [SMC] Device [10b8:2602]
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
	Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
	Latency: 64 (16000ns min, 32000ns max), Cache Line Size: 128 bytes
	Interrupt: pin A routed to IRQ 18
	Region 0: I/O ports at e800 [size=256]
	Region 1: Memory at dffffc00 (32-bit, non-prefetchable) [size=1K]
	Expansion ROM at dffc0000 [disabled] [size=128K]
	Capabilities: [c0] Power Management version 2
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=100mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
		Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
	Kernel driver in use: adm8211


** USB devices:
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 003 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 004 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 003: ID 0fca:8004 Research In Motion, Ltd. Blackberry Handheld
Bus 003 Device 002: ID 046d:c018 Logitech, Inc. Optical Wheel Mouse
Bus 002 Device 002: ID 03f0:0517 Hewlett-Packard LaserJet 1000


-- System Information:
Debian Release: wheezy/sid
  APT prefers unstable
  APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)

Kernel: Linux 2.6.32-5-686 (SMP w/2 CPU cores)
Locale: LANG=C, LC_CTYPE=C (charmap=ANSI_X3.4-1968)
Shell: /bin/sh linked to /bin/bash

Versions of packages linux-image-2.6.38-2-686 depends on:
ii  debconf [debconf-2.0]         1.5.38     Debian configuration management sy
ii  initramfs-tools [linux-initra 0.98.8     tools for generating an initramfs
ii  linux-base                    3.2        Linux image base package
ii  module-init-tools             3.12-1     tools for managing Linux kernel mo

Versions of packages linux-image-2.6.38-2-686 recommends:
ii  firmware-linux-free           3          Binary firmware for various driver
ii  libc6-i686                    2.11.2-11  Embedded GNU C Library: Shared lib

Versions of packages linux-image-2.6.38-2-686 suggests:
ii  grub-pc                      1.99~rc1-12 GRand Unified Bootloader, version 
pn  linux-doc-2.6.38             <none>      (no description available)

Versions of packages linux-image-2.6.38-2-686 is related to:
pn  firmware-bnx2                 <none>     (no description available)
pn  firmware-bnx2x                <none>     (no description available)
pn  firmware-ipw2x00              <none>     (no description available)
pn  firmware-ivtv                 <none>     (no description available)
pn  firmware-iwlwifi              <none>     (no description available)
pn  firmware-linux                <none>     (no description available)
pn  firmware-linux-nonfree        <none>     (no description available)
pn  firmware-qlogic               <none>     (no description available)
pn  firmware-ralink               <none>     (no description available)
pn  xen-hypervisor                <none>     (no description available)

-- debconf information:
  linux-image-2.6.38-2-686/postinst/depmod-error-initrd-2.6.38-2-686: false
  linux-image-2.6.38-2-686/postinst/ignoring-do-bootloader-2.6.38-2-686:
* linux-image-2.6.38-2-686/postinst/missing-firmware-2.6.38-2-686:
  linux-image-2.6.38-2-686/prerm/removing-running-kernel-2.6.38-2-686: true



Reply to: