Bug#523201: linux-image-2.6.29-1-686: ath5k - connection drops after 4-8 hours with NoProbeResp error
Package: linux-image-2.6.29-1-686
Version: 2.6.29-1
Severity: important
After initially connecting with WEP, my connection will drop with the error seen in dmesg (below, the NoProbeResp error; unsupported jumbo appears to be merely a warning) between 4 and 8 hours later. I can not reassociate with the AP until I toggle the wireless off and on (using the ACPI scripts). The connection dropping does not appear to be affected by network activity load.
-- Package-specific info:
** Version:
Linux version 2.6.29-1-686 (Debian 2.6.29-1) (waldi@debian.org) (gcc version 4.3.3 (Debian 4.3.3-5) ) #1 SMP Tue Mar 24 23:05:52 UTC 2009
** Command line:
root=/dev/sda2 ro quiet
** Not tainted
** Kernel log:
[307472.854331] wlan0: associated
[307477.512037] wlan0: no IPv6 routers present
[307892.139091] ath5k phy14: unsupported jumbo
[310665.794914] ath5k phy14: unsupported jumbo
[317968.425413] ath5k phy14: unsupported jumbo
[318781.422384] ath5k phy14: unsupported jumbo
[321276.333482] ath5k phy14: noise floor calibration timeout (2412MHz)
[321877.333465] ath5k phy14: noise floor calibration timeout (2412MHz)
[324288.333464] ath5k phy14: noise floor calibration timeout (2412MHz)
[324293.340087] wlan0: No ProbeResp from current AP 00:0f:66:ba:81:6e - assume out of range
[325709.333465] ath5k phy14: noise floor calibration timeout (2412MHz)
[336390.333416] ath5k phy14: noise floor calibration timeout (2412MHz)
[341969.464401] ath5k 0000:01:00.0: PCI INT A disabled
[341971.433355] pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x00ffff]
[341971.433670] ath5k 0000:01:00.0: enabling device (0000 -> 0002)
[341971.433689] ath5k 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[341971.433712] ath5k 0000:01:00.0: setting latency timer to 64
[341971.433888] ath5k 0000:01:00.0: registered as 'phy15'
[341971.526023] wmaster0 (ath5k): not using net_device_ops yet
[341971.527771] phy15: Selected rate control algorithm 'minstrel'
[341971.527814] wlan0 (ath5k): not using net_device_ops yet
[341971.529637] ath5k phy15: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[341971.744599] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[341972.776029] wlan0: authenticate with AP 00:0f:66:ba:81:6e
[341972.788255] wlan0: authenticated
[341972.788265] wlan0: associate with AP 00:0f:66:ba:81:6e
[341972.790053] wlan0: RX AssocResp from 00:0f:66:ba:81:6e (capab=0x411 status=0 aid=4)
[341972.790062] wlan0: associated
[341972.791695] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[341976.894743] wlan0: authenticate with AP 00:0f:66:ba:81:6e
[341976.896449] wlan0: authenticated
[341976.896460] wlan0: associate with AP 00:0f:66:ba:81:6e
[341976.898314] wlan0: RX ReassocResp from 00:0f:66:ba:81:6e (capab=0x411 status=0 aid=4)
[341976.898326] wlan0: associated
[341983.384074] wlan0: no IPv6 routers present
[343330.920551] ath5k phy15: unsupported jumbo
[347399.027849] ath5k phy15: unsupported jumbo
[357653.358820] ath5k phy15: unsupported jumbo
[364180.645523] ath5k phy15: unsupported jumbo
[366705.836075] usb 1-2: new high speed USB device using ehci_hcd and address 7
[366709.045626] ehci_hcd 0000:00:1d.7: port 2 reset error -110
[366709.045644] hub 1-0:1.0: hub_port_status failed (err = -32)
[366709.248078] hub 1-0:1.0: unable to enumerate USB device on port 2
[366709.504078] usb 2-2: new full speed USB device using uhci_hcd and address 4
[366709.649138] usb 2-2: not running at top speed; connect to a high speed hub
[366709.691142] usb 2-2: New USB device found, idVendor=0781, idProduct=7432
[366709.691154] usb 2-2: New USB device strings: Mfr=6, Product=7, SerialNumber=8
[366709.691162] usb 2-2: Product: SanDisk Sansa Clip
[366709.691168] usb 2-2: Manufacturer: SanDisk
[366709.691174] usb 2-2: SerialNumber: D90909055586B4870000000000000000
[366709.691409] usb 2-2: configuration #1 chosen from 1 choice
[366709.707144] scsi7 : SCSI emulation for USB Mass Storage devices
[366709.719156] usb-storage: device found at 4
[366709.719164] usb-storage: waiting for device to settle before scanning
[366714.717252] usb-storage: device scan complete
[366714.720602] scsi 7:0:0:0: Direct-Access SanDisk Sansa Clip 1GB v01. PQ: 0 ANSI: 0
[366714.729201] sd 7:0:0:0: [sde] 1986048 512-byte hardware sectors: (1.01 GB/969 MiB)
[366714.732467] sd 7:0:0:0: [sde] Write Protect is off
[366714.732477] sd 7:0:0:0: [sde] Mode Sense: 04 00 00 00
[366714.732485] sd 7:0:0:0: [sde] Assuming drive cache: write through
[366714.759364] sd 7:0:0:0: [sde] 1986048 512-byte hardware sectors: (1.01 GB/969 MiB)
[366714.762317] sd 7:0:0:0: [sde] Write Protect is off
[366714.762329] sd 7:0:0:0: [sde] Mode Sense: 04 00 00 00
[366714.762336] sd 7:0:0:0: [sde] Assuming drive cache: write through
[366714.762359] sde:
[366714.772647] sd 7:0:0:0: [sde] Attached SCSI removable disk
[367258.830922] ath5k phy15: unsupported jumbo
[370087.315346] ath5k phy15: unsupported jumbo
[377080.068623] ath5k phy15: unsupported jumbo
[382475.186146] ath5k phy15: unsupported jumbo
[386479.584521] ath5k phy15: unsupported jumbo
[389350.189673] ath5k phy15: unsupported jumbo
[391264.509669] ath5k phy15: unsupported jumbo
[394156.984097] usb 2-2: USB disconnect, address 4
[403252.333465] ath5k phy15: noise floor calibration timeout (2412MHz)
[422963.333467] ath5k phy15: noise floor calibration timeout (2412MHz)
[422964.008081] wlan0: No ProbeResp from current AP 00:0f:66:ba:81:6e - assume out of range
[430640.912446] ath5k 0000:01:00.0: PCI INT A disabled
[430642.800905] pci 0000:01:00.0: reg 10 64bit mmio: [0x000000-0x00ffff]
[430642.801217] ath5k 0000:01:00.0: enabling device (0000 -> 0002)
[430642.801236] ath5k 0000:01:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18
[430642.801259] ath5k 0000:01:00.0: setting latency timer to 64
[430642.801478] ath5k 0000:01:00.0: registered as 'phy16'
[430642.875032] wmaster0 (ath5k): not using net_device_ops yet
[430642.876809] phy16: Selected rate control algorithm 'minstrel'
[430642.876852] wlan0 (ath5k): not using net_device_ops yet
[430642.878682] ath5k phy16: Atheros AR2425 chip found (MAC: 0xe2, PHY: 0x70)
[430643.121014] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[430644.375837] wlan0: authenticate with AP 00:0f:66:ba:81:6e
[430644.378938] wlan0: authenticated
[430644.378947] wlan0: associate with AP 00:0f:66:ba:81:6e
[430644.380966] wlan0: RX AssocResp from 00:0f:66:ba:81:6e (capab=0x411 status=0 aid=4)
[430644.380977] wlan0: associated
[430644.382610] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[430652.459472] wlan0: authenticate with AP 00:0f:66:ba:81:6e
[430652.461684] wlan0: authenticated
[430652.461695] wlan0: associate with AP 00:0f:66:ba:81:6e
[430652.464958] wlan0: RX ReassocResp from 00:0f:66:ba:81:6e (capab=0x411 status=0 aid=4)
[430652.464969] wlan0: associated
[430655.192066] wlan0: no IPv6 routers present
** Loaded modules:
Module Size Used by
nls_utf8 1472 0
nls_cp437 5304 0
vfat 8672 0
fat 41688 1 vfat
nls_base 6508 4 nls_utf8,nls_cp437,vfat,fat
i915 129464 2
drm 133260 3 i915
i2c_algo_bit 4888 1 i915
rfkill_input 5252 0
ipv6 232468 12
nfsd 186396 17
exportfs 3900 1 nfsd
nfs 214976 0
lockd 57840 2 nfsd,nfs
nfs_acl 2624 2 nfsd,nfs
auth_rpcgss 31344 2 nfsd,nfs
sunrpc 161964 15 nfsd,nfs,lockd,nfs_acl,auth_rpcgss
raid0 6176 0
raid1 18248 0
md_mod 74108 2 raid0,raid1
joydev 8560 0
evdev 8160 13
serio_raw 4544 0
psmouse 36628 0
i2c_i801 8104 0
snd_pcsp 8476 0
i2c_core 20828 4 i915,drm,i2c_algo_bit,i2c_i801
rng_core 3644 0
iTCO_wdt 9880 0
arc4 1544 2
ecb 2352 2
snd_hda_codec_realtek 173504 1
ath5k 96796 0
snd_hda_intel 22092 0
mac80211 135592 1 ath5k
snd_hda_codec 58808 2 snd_hda_codec_realtek,snd_hda_intel
led_class 3668 1 ath5k
snd_hwdep 6000 1 snd_hda_codec
cfg80211 33000 2 ath5k,mac80211
snd_pcm 62704 3 snd_pcsp,snd_hda_intel,snd_hda_codec
snd_timer 17808 1 snd_pcm
atl2 23032 0
snd 48420 7 snd_pcsp,snd_hda_codec_realtek,snd_hda_intel,snd_hda_codec,snd_hwdep,snd_pcm,snd_timer
soundcore 6204 1 snd
intel_agp 22548 1
snd_page_alloc 8036 2 snd_hda_intel,snd_pcm
agpgart 30624 3 drm,intel_agp
video 16348 0
output 2504 1 video
battery 5832 0
eeepc_laptop 10120 0
ac 2872 0
rfkill 9576 3 rfkill_input,eeepc_laptop
button 5672 0
ext3 107180 3
jbd 42500 1 ext3
mbcache 7180 1 ext3
sd_mod 28252 6
crc_t10dif 1616 1 sd_mod
usb_storage 83468 2
ide_pci_generic 3408 0
ide_core 91820 1 ide_pci_generic
ata_generic 4316 0
ahci 27568 0
ata_piix 20092 1
libata 148892 3 ata_generic,ahci,ata_piix
uhci_hcd 19392 0
ehci_hcd 29836 0
scsi_mod 132076 3 sd_mod,usb_storage,libata
usbcore 124872 4 usb_storage,uhci_hcd,ehci_hcd
thermal 15092 0
processor 39540 2 thermal
fan 4104 0
thermal_sys 10272 4 video,thermal,processor,fan
** PCI devices:
00:00.0 Host bridge [0600]: Intel Corporation Mobile 915GM/PM/GMS/910GML Express Processor to DRAM Controller [8086:2590] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:82d9]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR- INTx-
Latency: 0
Capabilities: <access denied>
Kernel driver in use: agpgart-intel
00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2592] (rev 04) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7f00000 (32-bit, non-prefetchable) [size=512K]
Region 1: I/O ports at ec00 [size=8]
Region 2: Memory at d0000000 (32-bit, prefetchable) [size=256M]
Region 3: Memory at f7ec0000 (32-bit, non-prefetchable) [size=256K]
Expansion ROM at <unassigned> [disabled]
Capabilities: <access denied>
00:02.1 Display controller [0380]: Intel Corporation Mobile 915GM/GMS/910GML Express Graphics Controller [8086:2792] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:82d9]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: Memory at f7f80000 (32-bit, non-prefetchable) [size=512K]
Capabilities: <access denied>
00:1b.0 Audio device [0403]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) High Definition Audio Controller [8086:2668] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:82a1]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7eb8000 (64-bit, non-prefetchable) [size=16K]
Capabilities: <access denied>
Kernel driver in use: HDA Intel
00:1c.0 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 [8086:2660] (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.1 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 2 [8086:2662] (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
Memory behind bridge: fbf00000-fbffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1c.2 PCI bridge [0604]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 3 [8086:2664] (rev 04) (prog-if 00 [Normal decode])
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Bus: primary=00, secondary=01, subordinate=02, sec-latency=0
Memory behind bridge: f8000000-fbefffff
Prefetchable memory behind bridge: 00000000f0000000-00000000f6ffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
Kernel driver in use: pcieport-driver
00:1d.0 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 [8086:2658] (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 4: I/O ports at e400 [size=32]
Kernel driver in use: uhci_hcd
00:1d.1 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 [8086:2659] (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at e480 [size=32]
Kernel driver in use: uhci_hcd
00:1d.2 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 [8086:265a] (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin C routed to IRQ 18
Region 4: I/O ports at e800 [size=32]
Kernel driver in use: uhci_hcd
00:1d.3 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 [8086:265b] (rev 04) (prog-if 00 [UHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin D routed to IRQ 16
Region 4: I/O ports at e880 [size=32]
Kernel driver in use: uhci_hcd
00:1d.7 USB Controller [0c03]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller [8086:265c] (rev 04) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 23
Region 0: Memory at f7eb7c00 (32-bit, non-prefetchable) [size=1K]
Capabilities: <access denied>
Kernel driver in use: ehci_hcd
00:1e.0 PCI bridge [0604]: Intel Corporation 82801 Mobile PCI Bridge [8086:2448] (rev d4) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=05, subordinate=05, sec-latency=32
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: <access denied>
00:1f.0 ISA bridge [0601]: Intel Corporation 82801FBM (ICH6M) LPC Interface Bridge [8086:2641] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
00:1f.2 IDE interface [0101]: Intel Corporation 82801FBM (ICH6M) SATA Controller [8086:2653] (rev 04) (prog-if 80 [Master])
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin B routed to IRQ 19
Region 0: I/O ports at 01f0 [size=8]
Region 1: I/O ports at 03f4 [size=1]
Region 2: I/O ports at 0170 [size=8]
Region 3: I/O ports at 0374 [size=1]
Region 4: I/O ports at ffa0 [size=16]
Capabilities: <access denied>
Kernel driver in use: ata_piix
00:1f.3 SMBus [0c05]: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller [8086:266a] (rev 04)
Subsystem: ASUSTeK Computer Inc. Device [1043:82d8]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin B routed to IRQ 19
Region 4: I/O ports at 0400 [size=32]
Kernel driver in use: i801_smbus
01:00.0 Ethernet controller [0200]: Atheros Communications Inc. AR242x 802.11abg Wireless PCI Express Adapter [168c:001c] (rev 01)
Subsystem: Device [1a3b:1026]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 18
Region 0: Memory at f8000000 (64-bit, non-prefetchable) [size=64K]
Capabilities: <access denied>
Kernel driver in use: ath5k
03:00.0 Ethernet controller [0200]: Attansic Technology Corp. L2 100 Mbit Ethernet Adapter [1969:2048] (rev a0)
Subsystem: ASUSTeK Computer Inc. Device [1043:8233]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 16 bytes
Interrupt: pin A routed to IRQ 17
Region 0: Memory at fbfc0000 (64-bit, non-prefetchable) [size=256K]
Expansion ROM at fbfa0000 [disabled] [size=128K]
Capabilities: <access denied>
Kernel driver in use: atl2
-- System Information:
Debian Release: squeeze/sid
APT prefers unstable
APT policy: (500, 'unstable'), (1, 'experimental')
Architecture: i386 (i686)
Kernel: Linux 2.6.29-1-686 (SMP w/1 CPU core)
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/dash
Versions of packages linux-image-2.6.29-1-686 depends on:
ii debconf [debconf-2.0] 1.5.26 Debian configuration management sy
ii initramfs-tools [linux-initra 0.93.1 tools for generating an initramfs
ii module-init-tools 3.7-pre9-1 tools for managing Linux kernel mo
Versions of packages linux-image-2.6.29-1-686 recommends:
ii libc6-i686 2.9-6 GNU C Library: Shared libraries [i
Versions of packages linux-image-2.6.29-1-686 suggests:
ii grub 0.97-47lenny2 GRand Unified Bootloader (Legacy v
pn linux-doc-2.6.29 <none> (no description available)
-- debconf information:
linux-image-2.6.29-1-686/preinst/abort-overwrite-2.6.29-1-686:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.29-1-686/preinst/overwriting-modules-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/elilo-initrd-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/initrd-2.6.29-1-686:
linux-image-2.6.29-1-686/preinst/bootloader-initrd-2.6.29-1-686: true
linux-image-2.6.29-1-686/postinst/bootloader-test-error-2.6.29-1-686:
linux-image-2.6.29-1-686/postinst/depmod-error-initrd-2.6.29-1-686: false
linux-image-2.6.29-1-686/prerm/removing-running-kernel-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/lilo-has-ramdisk:
linux-image-2.6.29-1-686/postinst/old-system-map-link-2.6.29-1-686: true
linux-image-2.6.29-1-686/postinst/kimage-is-a-directory:
linux-image-2.6.29-1-686/postinst/old-dir-initrd-link-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/lilo-initrd-2.6.29-1-686: true
linux-image-2.6.29-1-686/postinst/depmod-error-2.6.29-1-686: false
linux-image-2.6.29-1-686/postinst/bootloader-error-2.6.29-1-686:
linux-image-2.6.29-1-686/preinst/failed-to-move-modules-2.6.29-1-686:
linux-image-2.6.29-1-686/postinst/create-kimage-link-2.6.29-1-686: true
linux-image-2.6.29-1-686/prerm/would-invalidate-boot-loader-2.6.29-1-686: true
linux-image-2.6.29-1-686/preinst/abort-install-2.6.29-1-686:
linux-image-2.6.29-1-686/postinst/old-initrd-link-2.6.29-1-686: true
Reply to: