Bug#441847: linux-image-2.6.21-2-486: poor via sata performance
Package: linux-image-2.6.21-2-486
Version: 2.6.21-6
Severity: normal
I put several drives into a computer to zero them. With hdparm -t -T the
sata drives appear to be the fastest but when writing urandom to all
drives in parallel the order of speed observed is
1) USB2 fastest
2) IDE master (slightly slower than USB when the same drive connected)
3) IDE slave (slightly slower than master)
4) SATA ( *MUCH* slower than either IDE or USB although much faster
drive connected)
11438284+0 records in
11438283+0 records out
5856400896 bytes (5.9 GB) copied, 5634.55 seconds, 1.0 MB/s
3815947+0 records in
3815947+0 records out
1953764864 bytes (2.0 GB) copied, 5634.55 seconds, 347 kB/s
14239665+0 records in
14239665+0 records out
7290708480 bytes (7.3 GB) copied, 5634.55 seconds, 1.3 MB/s
The SATA drives below:
1032778+0 records in
1032777+0 records out
528781824 bytes (529 MB) copied, 5636.55 seconds, 93.8 kB/s
1030113+0 records in
1030113+0 records out
527417856 bytes (527 MB) copied, 5639.4 seconds, 93.5 kB/s
Note that the SATA drives appear much faster when used separately. But
when IO has to be scheduled to all drives they get the least throughput.
-- Package-specific info:
** Version: Linux version 2.6.21-2-486 (Debian 2.6.21-6) (waldi@debian.org) (gcc version 4.1.3 20070629 (prerelease) (Debian 4.1.2-13)) #1 Wed Jul 11 03:17:09 UTC 2007
** Not tainted
** Kernel log:
p() start: 0000000000100000 size: 000000001fef0000 end: 000000001fff0000 type: 1
copy_e820_map() type is E820_RAM
copy_e820_map() start: 000000001fff0000 size: 0000000000003000 end: 000000001fff3000 type: 4
copy_e820_map() start: 000000001fff3000 size: 000000000000d000 end: 0000000020000000 type: 3
copy_e820_map() start: 00000000fec00000 size: 0000000000001000 end: 00000000fec01000 type: 2
copy_e820_map() start: 00000000fee00000 size: 0000000000001000 end: 00000000fee01000 type: 2
copy_e820_map() start: 00000000ffff0000 size: 0000000000010000 end: 0000000100000000 type: 2
BIOS-e820: 0000000000000000 - 000000000009f800 (usable)
BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f4e10
Entering add_active_range(0, 0, 131056) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 131056
early_node_map[1] active PFN ranges
0: 0 -> 131056
On node 0 totalpages: 131056
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 991 pages used for memmap
Normal zone: 125969 pages, LIFO batch:31
DMI 2.3 present.
ACPI: RSDP 000F8C80, 0014 (r0 VIAK8M)
ACPI: RSDT 1FFF3040, 002C (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
ACPI: FACP 1FFF30C0, 0074 (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
ACPI: DSDT 1FFF3180, 4DD8 (r1 VIAK8M AWRDACPI 1000 MSFT 100000E)
ACPI: FACS 1FFF0000, 0040
ACPI: APIC 1FFF7FC0, 005A (r1 VIAK8M AWRDACPI 42302E31 AWRD 0)
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
Processor #0 15:12 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
Allocating PCI resources starting at 30000000 (gap: 20000000:dec00000)
Built 1 zonelists. Total pages: 130033
Kernel command line: initrd=initrd.img boot=live xdebconf usplash username=ghost hostname=debian-live fetch=ftp://195.113.15.10/filesystem.squashfs BOOT_IMAGE=vmlinuz
mapped APIC to ffffd000 (fee00000)
mapped IOAPIC to ffffc000 (fec00000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1599.989 MHz processor.
Console: colour VGA+ 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 511448k/524224k available (1629k kernel code, 12116k reserved, 645k data, 300k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xfffb6000 - 0xfffff000 ( 292 kB)
vmalloc : 0xe0800000 - 0xfffb4000 ( 503 MB)
lowmem : 0xc0000000 - 0xdfff0000 ( 511 MB)
.init : 0xc033c000 - 0xc0387000 ( 300 kB)
.data : 0xc0297565 - 0xc0338cf4 ( 645 kB)
.text : 0xc0100000 - 0xc0297565 (1629 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay using timer specific routine.. 3203.46 BogoMIPS (lpj=6406921)
Security Framework v1.0.0 initialized
SELinux: Disabled at boot.
Capability LSM initialized
Mount-cache hash table entries: 512
CPU: After generic identify, caps: 078bfbff e3d3fbff 00000000 00000000 00000001 00000000 00000001
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps: 078bfbff e3d3fbff 00000000 00000410 00000001 00000000 00000001
Compat vDSO mapped to ffffe000.
CPU: AMD Sempron(tm) Processor 2800+ stepping 02
Checking 'hlt' instruction... OK.
ACPI: Core revision 20070126
ENABLING IO-APIC IRQs
...TIMER: vector=0x31 apic1=0 pin1=2 apic2=0 pin2=0
Booting paravirtualized kernel on bare hardware
NET: Registered protocol family 16
EISA bus registered
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfb140, last bus=1
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: Interpreter enabled
ACPI: (supports S0 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: Probing PCI hardware (bus 00)
Boot video device is 0000:01:00.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 6 7 *10 11 12)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 6 7 10 *11 12)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 6 7 10 11 *12)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 6 7 10 11 12) *0, disabled.
ACPI: PCI Interrupt Link [ALKA] (IRQs *20)
ACPI: PCI Interrupt Link [ALKB] (IRQs *21)
ACPI: PCI Interrupt Link [ALKC] (IRQs *22)
ACPI: PCI Interrupt Link [ALKD] (IRQs *23)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 13 devices
PnPBIOS: Disabled by ACPI PNP
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NET: Registered protocol family 8
NET: Registered protocol family 20
pnp: 00:00: iomem range 0xd0000-0xd3fff has been reserved
pnp: 00:00: iomem range 0xda000-0xdbfff has been reserved
pnp: 00:00: iomem range 0xf0000-0xfbfff could not be reserved
pnp: 00:00: iomem range 0xfc000-0xfffff could not be reserved
pnp: 00:02: ioport range 0x4000-0x407f has been reserved
pnp: 00:02: ioport range 0x5000-0x500f has been reserved
Time: tsc clocksource has been installed.
PCI: Bridge: 0000:00:01.0
IO window: disabled.
MEM window: e2000000-e3ffffff
PREFETCH window: e0000000-e1ffffff
PCI: Setting latency timer of device 0000:00:01.0 to 64
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 5, 131072 bytes)
TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 4755k freed
audit: initializing netlink socket (disabled)
audit(1189515918.756:1): initialized
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:09: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0a: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
mice: PS/2 mouse device common for all mice
EISA: Probing bus 0 at eisa.0
Cannot allocate resource for EISA slot 4
Cannot allocate resource for EISA slot 5
EISA: Detected 0 cards.
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI Shortcut mode
Freeing unused kernel memory: 300k freed
input: AT Translated Set 2 keyboard as /class/input/input0
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:10.0[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.0: UHCI Host Controller
uhci_hcd 0000:00:10.0: new USB bus registered, assigned bus number 1
uhci_hcd 0000:00:10.0: irq 16, io base 0x0000e700
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
via-rhine.c:v1.10-LK1.4.3 2007-03-06 Written by Donald Becker
via-rhine: Broken BIOS detected, avoid_D3 enabled.
ACPI: PCI Interrupt 0000:00:10.1[A] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.1: UHCI Host Controller
uhci_hcd 0000:00:10.1: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:10.1: irq 16, io base 0x0000e800
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.2[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.2: UHCI Host Controller
uhci_hcd 0000:00:10.2: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:10.2: irq 16, io base 0x0000e900
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:10.3[B] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 16
uhci_hcd 0000:00:10.3: UHCI Host Controller
uhci_hcd 0000:00:10.3: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:10.3: irq 16, io base 0x0000ea00
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 23
ACPI: PCI Interrupt 0000:00:12.0[A] -> Link [ALKD] -> GSI 23 (level, low) -> IRQ 17
eth0: VIA Rhine II at 0x1ec00, 00:13:d3:a5:a3:77, IRQ 17.
eth0: MII PHY found at address 1, status 0x786d advertising 01e1 Link 45e1.
ACPI: PCI Interrupt 0000:00:10.4[C] -> Link [ALKB] -> GSI 21 (level, low) -> IRQ 16
ehci_hcd 0000:00:10.4: EHCI Host Controller
ehci_hcd 0000:00:10.4: new USB bus registered, assigned bus number 5
ehci_hcd 0000:00:10.4: irq 16, io mem 0xe4000000
ehci_hcd 0000:00:10.4: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 8 ports detected
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
Registering unionfs 1.4
unionfs: debugging is not enabled
loop: loaded (max 8 devices)
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
Linux agpgart interface v0.102 (c) Dave Jones
agpgart: Detected AGP bridge 0
agpgart: AGP aperture is 512M @ 0xc0000000
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
SCSI subsystem initialized
shpchp: Standard Hot Plug PCI Controller Driver version: 0.4
libata version 2.20 loaded.
sata_via 0000:00:0f.0: version 2.1
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 20
ACPI: PCI Interrupt 0000:00:0f.0[B] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 18
sata_via 0000:00:0f.0: routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0x0001e000 ctl 0x0001e102 bmdma 0x0001e400 irq 18
ata2: SATA max UDMA/133 cmd 0x0001e200 ctl 0x0001e302 bmdma 0x0001e408 irq 18
scsi0 : sata_via
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
ATA: abnormal status 0x7F on port 0x0001e007
ATA: abnormal status 0x7F on port 0x0001e007
ata1.00: ATA-6: ST380817AS, 3.42, max UDMA/133
ata1.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata1.00: configured for UDMA/133
scsi1 : sata_via
input: PC Speaker as /class/input/input1
ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
Real Time Clock Driver v1.12ac
ATA: abnormal status 0x7F on port 0x0001e207
ATA: abnormal status 0x7F on port 0x0001e207
ata2.00: ATA-6: ST380817AS, 3.42, max UDMA/133
ata2.00: 156301488 sectors, multi 1: LBA48 NCQ (depth 0/32)
ata2.00: configured for UDMA/133
scsi 0:0:0:0: Direct-Access ATA ST380817AS 3.42 PQ: 0 ANSI: 5
scsi 1:0:0:0: Direct-Access ATA ST380817AS 3.42 PQ: 0 ANSI: 5
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
ACPI: PCI Interrupt 0000:00:0f.1[A] -> Link [ALKA] -> GSI 20 (level, low) -> IRQ 18
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xe600-0xe607, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xe608-0xe60f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
hda: ST340016A, ATA DISK drive
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sda: 156301488 512-byte hdwr sectors (80026 MB)
sda: Write Protect is off
sda: Mode Sense: 00 3a 00 00
SCSI device sda: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: unknown partition table
sd 0:0:0:0: Attached scsi disk sda
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
SCSI device sdb: 156301488 512-byte hdwr sectors (80026 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sdb: sdb1
sd 1:0:0:0: Attached scsi disk sdb
hdb: WDC AC21200H, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: ST340810A, ATA DISK drive
hdd: ST36531A, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00:11.5[C] -> Link [ALKC] -> GSI 22 (level, low) -> IRQ 19
PCI: Setting latency timer of device 0000:00:11.5 to 64
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
hda: unknown partition table
hdb: max request size: 128KiB
hdb: 2503872 sectors (1281 MB) w/128KiB Cache, CHS=2484/16/63, DMA
hdb: unknown partition table
hdc: max request size: 128KiB
hdc: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(33)
hdc: cache flushes not supported
hdc: unknown partition table
hdd: max request size: 128KiB
hdd: 12706470 sectors (6505 MB) w/128KiB Cache, CHS=13446/15/63, UDMA(33)
hdd: cache flushes not supported
hdd: unknown partition table
Warning! dirs delete and imap options to remount are ignored
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@redhat.com
Ebtables v2.0 registered
Bridge firewalling registered
fuse init (API version 7.8)
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
** Loaded modules:
Module Size Used by
tsdev 7616 0
usbhid 23008 0
hid 22912 1 usbhid
xt_multiport 3072 1
iptable_filter 2944 1
ip_tables 11464 1 iptable_filter
x_tables 14084 2 xt_multiport,ip_tables
ipv6 223904 8
fuse 40468 1
ebtable_broute 2304 0
bridge 47000 1 ebtable_broute
ebtable_nat 2432 0
ebtable_filter 2432 0
ebtables 17024 3 ebtable_broute,ebtable_nat,ebtable_filter
dm_snapshot 16288 0
dm_mirror 19092 0
dm_mod 51532 2 dm_snapshot,dm_mirror
ide_disk 15488 3
sd_mod 19856 2
snd_via82xx 26392 0
gameport 14600 1 snd_via82xx
snd_ac97_codec 92196 1 snd_via82xx
ac97_bus 2304 1 snd_ac97_codec
snd_pcm_oss 38816 0
floppy 54180 0
snd_mixer_oss 15360 1 snd_pcm_oss
snd_pcm 69896 3 snd_via82xx,snd_ac97_codec,snd_pcm_oss
snd_page_alloc 9608 2 snd_via82xx,snd_pcm
snd_mpu401_uart 7936 1 snd_via82xx
snd_seq_dummy 3844 0
snd_seq_oss 28928 0
snd_seq_midi 8224 0
snd_seq_midi_event 6912 2 snd_seq_oss,snd_seq_midi
snd_seq 44624 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event
snd_timer 20484 2 snd_pcm,snd_seq
parport_pc 32292 0
parport 32840 1 parport_pc
via82cxxx 8708 0 [permanent]
snd_rawmidi 22432 2 snd_mpu401_uart,snd_seq_midi
rtc 12440 0
snd_seq_device 7692 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq,snd_rawmidi
snd 46948 11 snd_via82xx,snd_ac97_codec,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_mpu401_uart,snd_seq_oss,snd_seq,snd_timer,snd_rawmidi,snd_seq_device
pcspkr 2944 0
k8temp 5632 0
i2c_viapro 8724 0
soundcore 7264 1 snd
i2c_core 20368 1 i2c_viapro
generic 4868 0 [permanent]
ide_core 113316 3 ide_disk,via82cxxx,generic
sata_via 11780 2
ata_generic 8196 0
libata 109460 2 sata_via,ata_generic
shpchp 30996 0
scsi_mod 133644 2 sd_mod,libata
pci_hotplug 28728 1 shpchp
amd64_agp 12292 1
agpgart 31664 1 amd64_agp
evdev 9216 1
squashfs 42628 1
loop 15240 2
unionfs 67624 1
ehci_hcd 30220 0
via_rhine 23176 0
mii 5376 1 via_rhine
uhci_hcd 22160 0
usbcore 121368 4 usbhid,ehci_hcd,uhci_hcd
thermal 14088 0
processor 23852 1 thermal
fan 4868 0
** PCI devices:
00:00.0 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:0204]
Subsystem: VIA Technologies, Inc. K8M800 Host Bridge [1106:0204]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at c0000000 (32-bit, prefetchable) [size=512M]
Capabilities: <access denied>
00:00.1 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:1204]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.2 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:2204]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.3 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:3204]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.4 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:4204]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:00.7 Host bridge [0600]: VIA Technologies, Inc. K8M800 Host Bridge [1106:7204]
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
00:01.0 PCI bridge [0604]: VIA Technologies, Inc. VT8237 PCI bridge [K8T800/K8T890 South] [1106:b188] (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
Memory behind bridge: e2000000-e3ffffff
Prefetchable memory behind bridge: e0000000-e1ffffff
Secondary status: 66MHz+ FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: <access denied>
00:0f.0 IDE interface [0101]: VIA Technologies, Inc. VIA VT6420 SATA RAID Controller [1106:3149] (rev 80) (prog-if 8f [Master SecP SecO PriP PriO])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin B routed to IRQ 18
Region 0: I/O ports at e000 [size=8]
Region 1: I/O ports at e100 [size=4]
Region 2: I/O ports at e200 [size=8]
Region 3: I/O ports at e300 [size=4]
Region 4: I/O ports at e400 [size=16]
Region 5: I/O ports at e500 [size=256]
Capabilities: <access denied>
00:0f.1 IDE interface [0101]: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT823x/A/C PIPC Bus Master IDE [1106:0571] (rev 06) (prog-if 8a [Master SecP PriP])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32
Interrupt: pin A routed to IRQ 18
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable) [size=1]
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable) [size=1]
Region 4: I/O ports at e600 [size=16]
Capabilities: <access denied>
00:10.0 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e700 [size=32]
Capabilities: <access denied>
00:10.1 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 16
Region 4: I/O ports at e800 [size=32]
Capabilities: <access denied>
00:10.2 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 4: I/O ports at e900 [size=32]
Capabilities: <access denied>
00:10.3 USB Controller [0c03]: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller [1106:3038] (rev 81) (prog-if 00 [UHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 32 bytes
Interrupt: pin B routed to IRQ 16
Region 4: I/O ports at ea00 [size=32]
Capabilities: <access denied>
00:10.4 USB Controller [0c03]: VIA Technologies, Inc. USB 2.0 [1106:3104] (rev 86) (prog-if 20 [EHCI])
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 64 bytes
Interrupt: pin C routed to IRQ 16
Region 0: Memory at e4000000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:11.0 ISA bridge [0601]: VIA Technologies, Inc. VT8237 ISA bridge [KT600/K8T800/K8T890 South] [1106:3227]
Subsystem: VIA Technologies, Inc. DFI KT600-AL Motherboard [1106:3227]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: <access denied>
00:11.5 Multimedia audio controller [0401]: VIA Technologies, Inc. VT8233/A/8235/8237 AC97 Audio Controller [1106:3059] (rev 60)
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 19
Region 0: I/O ports at eb00 [size=256]
Capabilities: <access denied>
00:12.0 Ethernet controller [0200]: VIA Technologies, Inc. VT6102 [Rhine-II] [1106:3065] (rev 78)
Subsystem: Micro-Star International Co., Ltd. Unknown device [1462:7181]
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 32 bytes
Interrupt: pin A routed to IRQ 17
Region 0: I/O ports at ec00 [size=256]
Region 1: Memory at e4001000 (32-bit, non-prefetchable) [size=256]
Capabilities: <access denied>
00:18.0 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration [1022:1100]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Capabilities: <access denied>
00:18.1 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map [1022:1101]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.2 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller [1022:1102]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
00:18.3 Host bridge [0600]: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control [1022:1103]
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
01:00.0 VGA compatible controller [0300]: nVidia Corporation NV5M64 [RIVA TNT2 Model 64/Model 64 Pro] [10de:002d] (rev 15) (prog-if 00 [VGA])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e2000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at e0000000 (32-bit, prefetchable) [size=32M]
[virtual] Expansion ROM at e3000000 [disabled] [size=64K]
Capabilities: <access denied>
-- System Information:
Debian Release: lenny/sid
APT prefers testing
APT policy: (500, 'testing')
Architecture: i386 (i686)
Kernel: Linux 2.6.21-2-486
Locale: LANG=en_US.UTF-8, LC_CTYPE=en_US.UTF-8 (charmap=UTF-8)
Shell: /bin/sh linked to /bin/bash
Versions of packages linux-image-2.6.21-2-486 depends on:
ii initramfs-tools [linux-initr 0.90a tools for generating an initramfs
ii module-init-tools 3.3-pre11-4 tools for managing Linux kernel mo
linux-image-2.6.21-2-486 recommends no packages.
-- debconf information:
shared/kernel-image/really-run-bootloader: true
linux-image-2.6.21-2-486/preinst/abort-overwrite-2.6.21-2-486:
linux-image-2.6.21-2-486/preinst/already-running-this-2.6.21-2-486:
linux-image-2.6.21-2-486/postinst/kimage-is-a-directory:
linux-image-2.6.21-2-486/preinst/abort-install-2.6.21-2-486:
linux-image-2.6.21-2-486/preinst/overwriting-modules-2.6.21-2-486: true
linux-image-2.6.21-2-486/postinst/create-kimage-link-2.6.21-2-486: true
linux-image-2.6.21-2-486/postinst/bootloader-error-2.6.21-2-486:
linux-image-2.6.21-2-486/preinst/failed-to-move-modules-2.6.21-2-486:
linux-image-2.6.21-2-486/preinst/initrd-2.6.21-2-486:
linux-image-2.6.21-2-486/postinst/depmod-error-initrd-2.6.21-2-486: false
linux-image-2.6.21-2-486/postinst/bootloader-test-error-2.6.21-2-486:
linux-image-2.6.21-2-486/postinst/old-dir-initrd-link-2.6.21-2-486: true
linux-image-2.6.21-2-486/prerm/removing-running-kernel-2.6.21-2-486: true
linux-image-2.6.21-2-486/preinst/elilo-initrd-2.6.21-2-486: true
linux-image-2.6.21-2-486/postinst/old-system-map-link-2.6.21-2-486: true
linux-image-2.6.21-2-486/postinst/old-initrd-link-2.6.21-2-486: true
linux-image-2.6.21-2-486/preinst/lilo-has-ramdisk:
linux-image-2.6.21-2-486/preinst/lilo-initrd-2.6.21-2-486: true
linux-image-2.6.21-2-486/prerm/would-invalidate-boot-loader-2.6.21-2-486: true
linux-image-2.6.21-2-486/postinst/depmod-error-2.6.21-2-486: false
linux-image-2.6.21-2-486/preinst/bootloader-initrd-2.6.21-2-486: true
Reply to: