[Date Prev][Date Next] [Thread Prev][Thread Next] [Date Index] [Thread Index]

potatoのインストール手順について



竹内@linuxです。
potatoをftpイメージをCDRに焼いてSS20にインストールしています。
ディスク構成は
sda	2.1G(外付)	ID:0	'/'
sdb	1.2G(内臓)	ID:1	'/boot','swap','/home'
sdc	2.1G(外付)	ID:2	'/usr'
sdd	1.2G(内臓)	ID:3	'/home1'
以下の手順で実行していますが
boot cdrom<CR>
boot: s
Release Nots
<Continue>
Debian GNU/Linux Installation Main Menu
Next : Configure the Keyboard<CR>
sun/sunkeymap:U.S. (Type 4/5)<CR>
Next : Initialize and Activate a Swap Partition
Select Swap Partition
/dev/sdb3: Linux swap<CR>
Should the bad-block scan be skipped on '/dev/sdb3'?<Yes>
Are You Sure?<Yes>
Next : Initialize a Linux Partition
Select Partition
/dev/sda1: Linux native<CR>
Pre-2.2 Linux Kernel Compatibility?<Yes>
Skip the Scan For Bad Blocks?<Yes>
Are You Sure?<Yes>
Mount as the Root Filesystem?<Yes>
Alternate : Initialize a Linux Partition<CR>
Select Partition
/dev/sdb1: Linux native<CR>
Pre-2.2 Linux Kernel Compatibility?<Yes>
Skp the Scan For Bad Blocks?<Yes>
Are You Sure?<Yes>
Select Mount Point
/boot: A small (5-10Mb) partition at the start of the disk.<CR>
Alternate : Initialize a Linux Partition<CR>
Select Partition
/dev/sdb5: Linux native<CR>
Pre-2.2 Linux Kernel Compatibility?<Yes>
Skp the Scan For Bad Blocks?<Yes>
Are You Sure?<Yes>
Select Mount Point
/home: User home directories.<CR>
Alternate : Initialize a Linux Partition<CR>
Select Partition
/dev/sdc1: Linux native<CR>
Pre-2.2 Linux Kernel Compatibility?<Yes>
Skp the Scan For Bad Blocks?<Yes>
Are You Sure?<Yes>
Select Mount Point
/usr: A large partition where most software resides.
Alternate : Initialize a Linux Partition<CR>
Select Partition
/dev/sdd1: Linux native<CR>
Pre-2.2 Linux Kernel Compatibility?<Yes>
Skp the Scan For Bad Blocks?<Yes>
Are You Sure?<Yes>
Select Mount Point
Other: Enter name of a different mount point.<CR>
/home1<Ok>
N3xt : Install Operation system Kernel and Modules<CR>
Please Wait
Next : Configure Deice Driver Modules<CR>
Question<Yes>
Select Category
ここで
block	Disks and disk-like devices.
fc4	.
fs	Drivers that allow many different filesystems to be accessed
ipv4	Internet Protocol drivers.
ipv6	Intenet Protocol version 6 drivers.
misc	drivers that don't fit in the other categories.
net	Drivers for network interface cards and network protocols.
scsi Drivers for SCSI controller cards and classes of SCSI device
と選択するメニューになるのですが、どれを選択したら良いのかをお教え願えな
いでしょうか。
ipv6は必要無いと思いますがそれ以外が分かりません。
また、それぞれの中にも選択するメニューが出てきます。それについてもお教え
願えないでしょうか。若しくはどこかに説明の文書が在りましたらよろしくお願
いします。
-- 
(o^o^o) Kiyomi Takeuchi
linux@wgy-jp.com
http://wgy-jp.com/



Reply to: