RE: Oggetto: Kernel panic
Hai ragione scusa .....
la macchina ha una piastra asus p2b -DS bi-processore con controller scsi
integrato Adaptec serie 7800, scheda di rete 3com 3c 509 ... ecc ..ecc
Allego il dmsg del disco di boot.
grazie.
Calibrating delay loop.. ok - 450.56 BogoMIPS
Memory: 256380k/262080k available (1136k kernel code, 384k reserved, 4180k data)
Swansea University Computer Society NET3.035 for Linux 2.0
NET3: Unix domain sockets 0.13 for Linux NET3.035.
Swansea University Computer Society TCP/IP for NET3.034
IP Protocols: IGMP, ICMP, UDP, TCP
VFS: Diskquotas version dquot_5.6.0 initialized_
Checking 386/387 coupling... Ok, fpu using exception 16 error reporting.
Checking 'hlt' instruction... Ok.
Linux version 2.0.36 (root@gondor) (gcc version 2.7.2.3) #2 Sun Jan 17 19:38:45
EST 1999
Starting kswapd v 1.4.2.2
Real Time Clock Driver v1.09
tpqic02: Runtime config, $Revision: 0.4.1.5 $, $Date: 1994/10/29 02:46:13 $
tpqic02: DMA buffers: 20 blocks, at address 0x282800 (0x2826ec)
Ramdisk driver initialized : 16 ramdisks of 4096K size
loop: registered device at major 7
ide: i82371 PIIX (Triton) on PCI bus 0 function 33
ide0: BM-DMA at 0xd800-0xd807
ide1: BM-DMA at 0xd808-0xd80f
hda: CRD-8322B, ATAPI CDROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
md driver 0.36.3 MAX_MD_DEV=4, MAX_REAL=8
(scsi0) <Adaptec AIC-7890/1 Ultra2 SCSI host adapter> found at PCI 6/0
(scsi0) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi0) Downloading sequencer code... 407 instructions downloaded
Failed initialization of WD-7000 SCSI card!
scsi0 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.4/3.2.4
<Adaptec AIC-7890/1 Ultra2 SCSI host adapter>
scsi : 1 host.
Vendor: FUJITSU Model: MAC3091SP Rev: 0103
Type: Direct-Access ANSI SCSI revision: 02
Detected scsi disk sda at scsi0, channel 0, id 0, lun 0
(scsi0:0:0:0) Synchronous at 20.0 Mbyte/sec, offset 31.
scsi : detected 1 SCSI disk total.
SCSI device sda: hdwr sector= 512 bytes. Sectors= 17871600 [8726 MB] [8.7 GB]
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 >
VFS: Mounted root (ext2 filesystem) readonly.
Adding Swap: 104384k swap-space (priority -1)
3c59x.c:v0.99E 5/12/98 Donald Becker
http://cesdis.gsfc.nasa.gov/linux/drivers/vortex.html
eth0: 3Com 3c905B Cyclone 100baseTx at 0xb800, 00:10:5a:73:71:2a, IRQ 11
8K byte-wide RAM 5:3 Rx:Tx split, autoselect/NWay Autonegotiation interface.
Enabling bus-master transmits and whole-frame receives.
Serial driver version 4.13 with no serial options enabled
tty00 at 0x03f8 (irq = 4) is a 16550A
tty01 at 0x02f8 (irq = 3) is a 16550A
PS/2 auxiliary pointing device detected -- driver installed.
On 08-Jun-99 Aaddante@HSNET.IT wrote:
> Dacci qualche particolare in piu' :)
> Confronta l'hardware rilevato dal vecchio kernel (output del processo di
> boot - comando dmesg) con quello del nuovo. Manca qualcosa (es. controller
> scsi)?
>
Reply to: